jonbearsmt

alternator is no substitute for reserve ( battery ) other then that i would say check all your connections again.. also where are you grounded in the rear..

lol so please share with us your "likes" of this sub... please. secondly buying a sub based on a Xmax figure is like buying a sports car because it has an ash tray

im NOT talking about the OP. nevermind.

same shit here, crows and there black purpluish shit.. and no lack of it.

yes i understand how, but alot of people dont, in fact i have seen the subsonic questions replied to countless times with, a simple response of 2-3 hz below tuning, with never reading the long way of how to that was my point.

far from Location:Down South

where are you located>?

I'm assuming you put the Micro SD Card, into a card converter to insert it to the PC. Does the card converter have a tiny switch on the side that says lock? sounds like you have your card locked. same shit both ways

i just got my 4gig micro Sd card in the mail, i put it in my gopro, and it recorded but when i put it in my computer it ask me to format the card... so i try to do so and it tells me it can not be formatted WTF!?

it was my fault i glued the top and sides of the spiders, but i did not lift it and glue the seat, .. i have done it this way 6 times before.. and never had a failure. but.. this time it failed.

thanks guys, ya know.. i do my fair share of recones, for my self and other people, but this goes to show, ya never know it all, i could avoided all this mess by taking an extra step and spending another 6 bucks, but hey ya live ya learn and my recones from here out will be better because of it... speaking of, i have a nightshade V1 to recone and a old school triple stacked BTL in line

the thing is that most time the SSf is set incorrectly becuse honestly they are hard to telll where you are... its a big circle, one is in 15 hz the other end is what 60hz (depending on the amp) and where you set it is pretty much a guess... you can only estimate where your setting the SSF, and thats where most failure lays IMO, my friend hugo (onebadmonte) has some kinda sweetish danish tool i donno what the hell it is. but its able to to sell you exactly where the SSf is while you adjust it, and also your roll off points a sweet tool when dialing in an active set up... he hooked me up years ago.. but of course my sub amp has changed, so i need it again !

re glued the spider landing today and repaired the leads then pushed it down and curved to it wont hit the cone, BOOM

and that was the last post before he asked for help about his unloaded subs. lol it will happen .

no need to ordered it you can find it local, most auto parts stores, any lowes home depot true value or mom and mom home repair shop,

the mixing nozel will look like this http://www.plumbersurplus.com/Prod/Devcon-20445-Flow-Mix-5-Minute-Epoxy-Clear/208853/Cat/1399 and today i am using the 5 min 1500 PSi one

if its not miss alighted then get some expoxy with the mixing nozzle and fix it for now. if it works it works.. if he dont it dont... cant mess it up any more!

nope

you guys are poop asses, the video is funny tho

from what im seeing your only checking one of the subs... the one thats moving a little im guessing, ...... well i would like to know what the readings are on the other sub... i think that one may be the issue, and im going with a single broken lead as well... and dont worry about a fluctuation of 1.0 and 1.2 your looking for 000000

in weight thats about right.. but finding someone to pay you that for it is something else.

the reason they use them is so that they can keep cost down, using the same parts, as apposed to tooling two different one for a very close size kits

ground to the frame in the rear and do the big three well and you will be set.

that was my thought bromo