CBFryman

Overkill mang.

Im just wondering what one of these runs for new. I found out that one of the local shops is a dealer. Before i go walking in there to fart on their knowledge like is my monthly ritual i'd like to know what these run for. Depending i may bite it and buy one assumeing it has the pause feature. I like the look of the CD3434 but i like the plain/almost stock look MUCH better.

Good Points besides the whole alblum: Soul Rebel Concreet Jungle Stand Up Jamrock One Love (people get ready) Exodus - The track on this CD is unmastered, or so it seems, so it isnt the best recording ive heard. Still a very excelent song.

everyone should have that bob-marley CD. Excelent alblum with excelent tracks.

medium rare FTW...steak and eggs for breakfast FTW... but im eating honey on wheat toast

oh and careless user + 2500w amp + clipped signal = death to most speakers

May be, when i see a 4HP place at world finals ill get that (if i even have the money)

Good Dinner = Crab Legs, Flakey Biscuts, and a good salad.

S P L

I'm not sure what basket you have, but the TC3000 soft parts require a 10" spider and the spacers are tall too, I know for a fact the 12 spoke and 4 spoke baskets that many companies like DD and RE use will not work.. they are too small. Its best you replace the entire top assembly to get the most out of the motor. I could give you smaller spiders with no spacing but then you're just back to a normal softparts. Whats your email address? Elias, the tc2k is a TC9 mot. <{POST_SNAPBACK}> [email protected] So there is no way to get a custom set of softparts made? Im not really up for spending $200 on softparts for a motor i paid 90 shipped for.

I sent TC an e-mail but ive yet to get a responce so ill ask here. I have a TC9 i am stealing off of an e12a to make a custom SPL driver. I was going to use Death Penulty soft parts but Incriminator is out and ive yet to receive word about new soft parts comming in. The intraweb bull about the Havoc using a modified TC9 is apparently bull so i cant use havoc soft parts. I assume i could use a TC3000 recone kit but i dont want to purchase the basket, just the soft parts. I was also wondering if it would be posible to have more SPL oriented soft parts made. I will be using a 15" 12spoke basket "hopefully"

efficency isnt bad at all. much better than the RL-S's 82.X also much better Q from the Rl-S which is almost 1.00 Qts.

das cool. People ask what is so good about john deere...well i'll tell you this, my uncle's john deere's would always beat the international's when we would get bored at the family reunions on his farm and start having tactor races. i sence a "you might just be a redneck" joke comming on.

i could get alot better milage if i had the 3.73 rearend instead of the 4.10 but then i couldnt pull a boat out as easily, espeically with thoes tires. It isnt the most powerful nor does it have the most torque, but it makes good torque down low and the curve is relatively flat, it pulls my parents 19' bayliner loaded with crap easily. Much easier than my moms 4cyl Nissan which makes around the same power (abotu 15 less) not quite as much torque (30lb/ft less) but the first 3,000 RPM or its 5,000 RPM range are worthless and the 3.XX rear end it has on thoes little tiny tires just about met their mach trying to pull the boat out of a boat ramp without much incline.

let me fill my truck bed with PA speakers... not

that picture makes me want to buy an MT and send it to you

mini john deere is because they only have 6acres, 3 of which arent used. Used to have one a lot bigger but they got rid of it when they got tired of taking care of it. i have some pictures of some big john deere's ive driven if you want to see big tractors. I dont know where his jointer is, i know he has one somewhere, a biscut cutter too, and the bandsaw is 12" 1hp motor...i dont know if that is good or bad...but it gets the job done Oh and i would be luckey...if he would let me use half of it. elderado, the shop shuns laws of physics...that is how he can turn out such nice stuff. like the bench for the chop saw, a "scrap" counter and cabinet.

I need to figure out how to get a grand or two for a project boat by mid winter then boat prices drop around here.

Wu Tang? *Throws up the W*

lol, welcome.

only thing i have is a BX1205D which i will sell in a few months probably but it isnt SQ oriented and it isnt new with warranty either

Audiobahn 10's to canada was $40. 24lb package. But the guy paid th extra (was offereing them for 70 shipped to the 48, he offered me 90 to canada so i made the same money)

We where going to build a ported box for my friends tiburon that mounted like the back deck that lifts when you open the hatch. You could do the same (except no lifting because its not a hatch). We where going to go with 3 Tang Band 8's, should be more than enough for a little car like yours or his

^x2 dont even have to unhook the positive if you remove the ground. If there is no potential for potential difference on the chassis so the (+) wont do jack didly.

The ginomous table saw didnt have the leaves one it so it was only like 3'x8' Fancy Router Table Fancy chop saw table (kust0m) Band Saw Small Drill Press (big one was put up) little plainer (big one up stairs) The kind of wood he has been working with recently Most of the pait and adheasives where gone from the last time i was out there. The John Deere 4100