CrazyKenKid

i will be doing that also! fuxk the harness lol!! killed my damn h/u hey is there is a way to replace that pico fuse? or does it HAVE to be sent in?

my next install will be kenwood flip out 7inch monitor excelon! should i ground this one to the chassis or to the harness?

did you ground the sony to the chassie or to the harness? b/c if it is recommenedi i will jsut ground to the chassis from now on.

so either no new info or i am one of those lucky guys who just get a surprize in the morning! loL!!

ground are normally suppose to be under 3ft. unless you have a direct run from the front battery if you connect it right to the battery how long can they be? (unlimited?)

Ya my deck does the same thing, when ever it moves it wines, and then i have to play with it and find just the right spot for it to stop wineing. i found out after that most of their decks you need to ground to the chasis and not this harness ... if u ground to the harness they will blow what no way? and i though grounding the rca's would fix it! turns out grounding to harness was wrong..sounds pretty wierd! your dad is a VP of fluke..MAN i need a fluke 75 (true rms one) dmm! can you get me a hook up? p/m me if you can or just send me an e-mail [email protected]

Get a sundown saz 3500!!!

is that why pioneer decks suck due to a blowing pico fuse blowing mysteriesly? that is why my h/u is giving me issues lol!! POS poineer junk

ya my alt also doesn't have a ground wire but it also mount with 2 screws and those 2 screws on mine are the gronding spots! so to complete the big 3 jsut run a wire from one of the 2 bolts to the chassis that way your alt and engine block will be grounded!! you might want to use 2 wires of 0/1 though!! wiat what are you asking? is it okay to ground your engine block to the chassis instaed...instead of what? Grounding your alt and engine to the chassis? but by grounding one your ground the other so...you may be okay!! sorry me vs reading and reading always wins!!

x2 how many batteries are you using for that 4000? that is 4krms at 1ohm right? also what is your voltage? do you have a volt meter to see what kind a voltage that amp is seeing?

well if you starve the amp for power it will work harder it might get hot but i am no expert and i could be dead wrong on that point.

i don't think that deck has one man! i believe you need to buy some thing like this to adjust those settings http://www.amazon.com/ALPINE-IMPRINT-AUDIO-PROCESSOR-ADD/dp/B001AQVTWQ/ref=pd_bxgy_e_img_b/179-9580204-6459944

screw you i seen the post first! i call first dibs lol!! jk!! first with cash wins! also he the for sale thread with prices is coming SOON he says!!

wow sounds like it was a pretty loud setup!!! make sure you post the link when you want to sell this stuff!! it should go ffast!! nice stuff you got there!! also which amps are you going to be selling?

lol funny story my wine in my speakers came back! so i jsut moved my deck in and out like 0.1 of an inch and the wine-ing went right away! so now i know there is a problem with my pioneer premier deck!

yep that is what Jacob is known for! the best customer service all around!!!

clipping is bad, it makes distortion which can blow speakers. When an amp is clipping it is being overdriven and it starts to cut off the tops of the soundwaves(so you get a square looking wave form). To fix this either listen to music within the limits of your amp. The only way to know that you are doing this is to listen for distortion, which of course is one of the reasons speakers blow. and for me distortion is hard to hear..maybe i jsut have bad hearing! Hope this helps also if you want to see the distortion you would have to buy a hand held o-scape!

what are you running the mono amp at? 0.5ohm? also to keep it cool have you tried some 120mm fans? to blow across the amp?

WOW I can't believe the amount of flex on your roof...that is CRAZY man!! I wonder if those 4 subs can handle more power? but ya very nice job!! you should get it metered looks like some high numbers!

oo ic! thank you!! i didn't know that!!

O i used a relay to wire the fans up! my amps and the fans are on a relay. i have the fans wired in parellel!! at night time they look pretty cool! I have to get a pic for you guys!!

lol the ns will love the 2000 but my car will not lol!! hey what do you guys think if i cover up the batteries with some mdf carpeted? like do the batcaps look like an eye sore?

good point! now that you point it out it is kind a an eye sore! now to hide it lol! thanks!!

Here is what i have noticed! when i turn on my car and the music starts to play the sub dones't kick in for a good 2-6seconds (i haven't done an official timing yet) as soon as i turn my car on though (turn the deck on i mean) the amps and fans all turn on, then the front stage first up right away and in a few seconds the sub will turn on. my question is why is this delay happening? did i do something wrong? i am currently using a relay for both my amps and fans so there shouldnt' be a problem. plus the amp is turning on right away so i dont' know what is up? maybe this is common i don't know so i thought i would ask! 1-15in NS 1- sae 1200d 4- fans 1- 100.4 2-batcap 2000s big 3 0/1 everywhere thanks for your time Kenneth

i don't have a camcorder but i guess i could do it with my camera lol!! that would be kind a cool! maybe i will do that when the saz2000 comes! or mabye i will jsut rent a camcorder!! (by rent i mean buy then return the next day!) lol