Crescendo Audio

I need experienced help ASAP Please!, 1- I would like to know how can i measure the total rms output of my amp using a multimeter and 2- How many volts could the BC3500 D amp do unloaded(with out the sub connected)? Thank you

Hi there, my name is Jim, and I'm new here. I can install but conceed I know very little about the science of what I'm doing, therefore I'm looking for a little help in optimizing my current project as it is different, and of course budget restricted. The project; I am currently refurbishing a boat, it's a '93, 21' Reinell Sunliner bowrider with Chev.305/Mercruiser I/o. I have a Rockford 15, and a sony xm-405eqx, a Alpine 9886 head unit I would like to use, also a pair of energy 4" coaxials. I am wondering about the Crescendo Super tweeter and 6.5's. Knowing I need more amp as well, at least another two channel. My goal is to fill this boat area with as full spectrum as p…

Im running 2 FI BL 18's with cooling and flatwind coils off an aq 2200d for now. I have 1 xs d3100 in the back now, with another being ordered soon, stock alt on 2012 scion xb now. I havent had any voltage issues now, but definitley getting another d3100. Will this be enough for a crescendo 3500d @ 1ohm? Thanks

Is there any direct way to contact Crescendo Audio? I have been dialing and leaving messages, emails and filling out that form for weeks and no answer, and I will really like to speaker to them, what can I do?

Navid's Expo demoing yesterday at a competition in South Florida. 10 15" Crossfire XS V2 on 4 Crescendo Audio BC5500D. Mids and Highs are the PWX on the Concerto Series amplifiers, it was loud and clean. The bass choked me out a little bit. Enjoy and let me know what you think.

Does anyone know the internal fuse rating for that amp? Im trying to calculate how much alt and batts i'll need to run four 3500's. Thanks

Are the cresendo mid range speakers decent?

Hi guys, I want to share with you my future setup and wanted to know if the stock electrical will be able to handle it: I am brand new at this car audio business I crescendo 3500D at 2 ohm -- 1900 W continuous power 1 FI BTL N2 12 running at 2 ohm 1 4 channel JBL 100 W rms each channel 4 jbl 6.5 1 Pioneer 9400 Box tuned to 32 Hz (got the cut sheets from BTL forums) I will be doing the Big 3 I have a 2004 Accord with stock alternator and yellow top optima Thanks guys

I finally got my bc2000d in and was so excited. I replaced my Rockford Fosgate T1500-1bdcp using all 0 guage wiring new XS Power in the back, stock alternator. Everything was gravy with the Fosgate. The new Crscendo diD NOT impress me at all.... Actually it was VERY lackluster, sounded like crap.... No bass , no power at all.... Sounded like a 300 watt amp compared to the Fosgate. First thing i noticed was the bass knob wasnt working. And the amp clipped every so often. The gain is barely at 1/4 and the bass boost, subsonic were off or at the lowest setting. Lpf set at around 80hz. Still sounded like garbage even without the remote knob Called crescendo and they shipped…

Ok I'm getting 2 12ssa zcons dual 1ohm. I got a BC3500 what would be the best way to wire the subs to it and the best wire to use. I think I'll have planty of power i got one xs power 5100R and going to put a second battery xs power 3100 with a mechman alt. all in a 1998 honda civic.

Ok I would like a new amp or a refund for my c1100.4 The day i received it all it did was protect..even with JUST rca's in. I changed rca's and everything checked all speakers (4 crescendo 8's and 2 cendo super tweets). It plays for a little and randomly protects. I call you guys and you tell me I need another battery JUST to run this SINGLE amp. So i got the battery STILL protect. I switch from high pass to low pass...guess what? Protect. I send the amp to you guys and you say it's fine and send it back to me , but I had the same problems when I received it again. I SEND THE AMP AGAIN. you guys say the 3rd channel went out due to low power and tell me i MUST have a secon…

What would be the best mid bass I could get for the ft1 "supertweeters"? I was thinking of going 8" but I dont think the ft1's would pair up with an 8" so maybe selenium 6"?

I ordered two FT1 4ohm tweeters and two PWX-8in mids 4ohm. Well the 8's that came are 8ohm.....Should I try and make this work or just send back for the 4 ohms? The amp is a Alpine PDX 4.150 and does rated at 4 or 2 ohms.

You can save $72.95 off of our C1100.4 4channel Amp from now until July 6th! $347.04 shipped in the USA! To order, visit C1100.4 - Crescendo Audio | Online Store and add to your cart with thei following coupon code: Happy early 4th of July, stay safe!

Hows it going. I'm looking to purchase the BC2000D to power my 2 12" GCONS @ 2 Ohms. What is the lead-time on this product? Thanks, SnapperKing

Hello, I was just wondering if there have been any posting of any of the amplifiers tested on a 16v setup. Clamped or not. Just interested what these would do, also, at what voltage will they go into protect. Really interested in the information abover for the 5500 series. Thanks

Ok, I bought a 2k last June-July and started buying the other stuff for my install. So long story short I got everything installed Monday. At first my amp was fine it protected one time the first day I had it, but I thought that was because I hit a big bump on the freeway. Tuesday I was heading back to the shop that did my install for them to finish my big 3 or 5 actually. So as I went to leave my amp protects. I restart the truck and start beating on it again and 30-40 sec later it protects. I call Navid and he says it might be my Bass Knob so I unplug it and beat on it with the car off and it plays fine. I played it for a min or two fine. Then I go for a drive with the …

Incase you missed it, Mark finished the website and it was launched around 3pm today on the 22nd. Check it out http://www.crescendoaudio.com/

Does anyone know how much power the bc2k amp puts out at .5 ohm?

I was just wondering if you guys could maybe list all products that are immediately available and pricing on each item as well in the meantime while the new site is being worked on. I always recommend the products but can never show locals the products without chasing down build logs which can be tedious while mobile and on the fly.

I bought a bc2k about 6 months ago and about 1 month ago my bass knob clipping light would work but the stop working till I tapped on it. Well a few days ago it finally stopped working all together. Is that part of the warranty? If not how much would it cost to buy a new one?