Test 1, 2, 3...

PM me about cosmetic defect Nightshades... I have a couple that don't meet my standards cosmetically. All listed items still for sale as of today -- 4/8/08.

Stop typing like that it is SUPER annoying. You think they are garbage, and I think you are an idiot. (note, equally fair statements) For a mainstream product, the Kicker is more than fine. I wouldn't say that it is the greatest deal I have seen and think you can get it cheaper but I might be biased. And yes, that box is way too small for that driver.

716

hello everyone i just got a quick question. i need some advice, I have a 2006 cadillac escalade with 26"s on it and i got 1 12inch jl audio w7 with a 2000 watt amp. it pounds really hard, its hits 135 on the decimal reading. i want to know what kind of door speakers to get so that I have amazing hi's in my doors. i want to be super loud and screaming over my base . what should i get? give me some insight. i got money so the cost dnt matter. hit me up

The loudspeaker circuit includes the connecting wire between the amplifier terminals and the speaker terminals, the amplifier internal impedance and the impedance of the speaker system. The wire could be copper or silver and perhaps coated with solder containing tin. wilson signal booster

The madness is about to begin.....again, well not to much. Remember i am not looking for a all out SPL setup, just a daily driver that is light on weight and still bangs...a solid 12 BL in a 2.0 cu ft enclosure~35Hz equipment: 12 BL dual 1 Alpine MRP M1000 (yes i know, no subsonic filter blah....it was stuffed away in my closet so i wanna give it some use) Knu Konceptz 4awg Kolossus cable Sundown 100.4 (JL 6.5s, tweets) Still need another set of components for the rear. Also my enclosure is temporary due to the fact i dont know if my new car rear seats fold down......if they dont i know there is a armrest that connects to trunk. Maybe aeroport straight forward. Previous…

Hi, i received the tracking number etc from FedEx on 1st of June, and has not been sent yet. Anticipated ship date Jun 1, 2011 Estimated delivery Jun 10, 2011 by 6:00 PM And I'm bit worried, since my city is not in the destination, only country, and county "NORWAY, FINNMARK NO" Never had things shipped with FedEx before.

Oh, I'm close as well. I'm thinkin what it is is alpine units bass control is not a crossover but a center frequency and you can adjust freq and bandwidth. What I have set is +2 on both bass and treble with highest bandwidth possible. So... I believe is slowly sloping the frequency range. I had to have it set like that with the last amps I had or it wouldn't get full clean power without a little help. If my next amps are like that, I'll just get a line driver and 3way x-over since I need that anyway

Do you mean 1.5 ft of port length?

694

Sorry i must have stated it wrong what i was trying to say is should i run two 1/0 POWER wires or will 1 be sufficient enough.

spam

If i have a 1.75 ft cubed box for the sa 12, what would be a good port width,length, and area? Any help would be much appreciated.

cadillac escalade

"Right Now AudioWrap is giving away a FREE license plate vibration damping kit for a limited time. Just send [email protected] an email with your address and we’ll send you a free sample. You have all heard that car at the stop light that sounds like it’s going to fall apart with all the rattles and vibrations you can’t enjoy the music. Act now there are a limited number of free samples. We stick where the competition falls down." Directly from Tim at Audio Wrap, Tell him Coleman sent you

THATS WHAT IN TALKIN BOUT! yeahhhhhhhhhh

/\ TOP

I think a 15" version of a SD-1 that could handle a 1000D would do exceptionally well. The 1000D is one of my overall favorites of the sundown amps for daily setups due to the size and power that it puts out. Have you thought about a 15" version?

Or simply respond on here either way works.

Double post fail..

Yes

Do you still have this? What makes it a B-stock? What would be some "actual" numbers at 4-ohm? atleast the 100x4? Thanks, Paul 100 x 4 watts @ 4 ohms 160 x 4 watts @ 2 ohms 320 x 2 watts @ 4 ohms bridged Damping Factor > 200 @ 4 Ohms 0.2v - 6v adjustable input sensitivity 10 Hz - 40,000 Hz Frequency Response Channel Separations: 75 dB > 90 dB S/N Ratio 4-Way Protection Circuit (Thermal, Overload, Speaker Short, and Over Current) Selectable HP / LP / FULL crossover CH 1 & 2 Variable HP crossover 50 - 5000 Hz @ 12 dB CH 1 & 2 Variable LP crossover 50 - 500 Hz @ 12 dB CH 3 & 4 Variable HP crossover 50 - 500 Hz @ 12 dB CH 3 & 4 Variable LP…

Danrnit I paid 150 for it a few weeks ago At $150 they did include a warranty. They now only have a non-DOA guarantee at the lower rate.

i havent measured it yet but i know that the box will [code]I AM AN IDIOT AND I CANNOT SPELL PROBABLY come alittle bit like 4 inches above the rear firewall..i dont mind that it does..ill get back to you guys with the measurement...and what amp would you guys think i should get..i herd good things about the HK4000D. wow so the admin on this sight change things that i say in my posts and then call me a idiot because i don't want to fully spell out the word probably? how childish. now that i know im back in high school and im in english class again ill try harder to impress you guys with spelling because that is more important than giving advice. ANYWAYS thank everyone i a…

ill be buying two more in by the 19th... would 4 12s in 7 cubes after all disp. @ 35 ideal with a 1500 on each one... the goal is 150 in a trunk car but will mostly be used as a daily system.