SPL & SQ / Fabrication

There used to be a few threads about things people were doing for SQ competition and some of the things each organization makes you have for max points in each category. I have a few questions about some of those things. I will be building based off of Usaci rules mainly because besides SBN (which offers Iasca as well) they have the most SQ comps in logical distances from me. My first question is about Processors, crossovers and EQ's. Do I need any of those three for max points or if I buy a HU that has all of those things built in will that count? If need be I will buy a cheaper HU and add something like the PPI-DCX730 as opposed to something like the Pioneer 880 or the…

My uncle had all the tools to help with the build but then a lady drove into his garage and in the process ran over the main gas line. His whole garage was torched, including the tools and his brand new Honda Pilot. Since the last time I've posted, I haven't had time to build it but a coworker of mine wants to help out with the build so I just wanted to go over some options. TIA My max outside dimensions: W=35" L=8.5" H=15". This is going in an '06 Suby wagon. The sealed box should work fine but I'm wondering if ported could work also. I listen to some rap, but mostly alternative and stuff like Blue October, Silversun Pickups, etc. I think I have the room for ported…

Just wanted to share this incredible build with you guys. 83 pages and still not finished. Attention to every detail. BERYLLIUM BMW 323ci. - CARSOUND.COM Forum Some pics so you know what you are going to find in the thread: And many many more beautiful stuff. Enjoy.

i will be purchasing either an IA DP 15D1 or an IA judge 15D1 and i would like to know a box recommendation for it and what tune would be good since there are no specs on here and their website. the other question is i want to fill the whole trunk with the box amp and second battery/ultracap i notice i will have a very tiny gap with the port facing the back(the trunk lid not the inside) for the ports to push air so i was going to do port and sub face up, just curious to know how much db i will lose from doing that instead of port back sub back or sub up

heya... i would like to know how close can a sub(magnet) come the back side .... ..(if the sub is 10" ... can the depth of the box be 16 > or if the sub is 18" ... can the width be 19" ) ...can it effect the sound ..?

I have my 3/4 thick mdf cut. Took me about 3 hours just to cut it. The only thing im confused about is putting 2 pieces of wood together. Would i have to apply wood glue to the 2 pieces, attach them together, and wait till it dries, then predrill, then screw? Im really confused. This is my first box. I dont want the edges to crack.

i want to thank those of you who pointed out the error of the batterys as projectiles. there in a safe place under the amp rack now... back seat has been removed / replaced with a flipp up amp rack boxx placed for fitt

See attached pdf for design & WinISO charts. This is the first time I've attempted this so I'm sure there's plenty wrong - looking to learn! Powered by a memphis 16-st1000d pushing 600w rms at 2 ohm. Box 2 design.pdf

I will be building 2 of these boxes sometime in the next week. There are matched to fit my tiny trunk (00 Mustang Vert)Each is 0.86896 cubic feet, tuned to 32 or 33hz. Each will house a CompVR 10 inch sub, Seeing around 400rms each. The boxes are from a friend so they will be free. There replacing prefab sealed boxes about .8 cubes I would like to know if theres anything wrong with my design. The port is 12.5 inches wide, by half an inch tall. It extends all the way until it is half an inch from the back wall.

I suck at google sketch. Can someone help me? I know the dimensions but I would like to see it in 3D. Width, 38 inches Height, 18 inches Top Depth, 10 inches Bottom Depth, 18 inches This is for a 15 inch sub. The sub will be mounted on the angled panel. I am using two 4 inch aero ports that will be mounted on the top 10x38 panel.

This is what happens when you get wood cut at home depot. I got all my cuts at home depot and some are 1/16 to short. they wasnt using the regular saw. i was wondering can i use some sealer tape for the cracks?

What size enclosure would best suit a 15 L7 for spl and tuned to what frequency

Vehicle : 2007 chrysler sebring Location in the vehicle: trunk Space available (Length x Width x Height): 37 wide x 32 length x 13 height i can get larger just would have to build inside trunk. Subwoofer make and model: Zcon D1 Subwoofer Size: 12 Number of Subwoofers:1 Type of Port (Kerfed, Slot, Aero, etc.): slot or aero What type of music do you like?: dubstep and decaf Is your goal SPL or Everyday Music?: most of my listening is everyday music decaf and dubstep. Tuning Freq (Hz): not sure Volume : currectly around 7 gross Questions: I have 2 zcons and am thinking of going to 1 due to rebuild thoughts. I need to give these subs more space and not sure i can do that w…

Crown Victorias have some pretty big trunks, i drive one. Heres a pictures Is there a way that i can place ONE piece of MDF and mount it somehow onto my trunk so i don't have to make a whole box. Its my car so i can use up that space however i want, place it anywhere in the trunk.( dont' have to worry about groceries etc.) I want to use 1 board, and the trunk itself to act as the rest of the box. Is that possible or will it be bad for my sub? Any help in this area will help, just bought a SSD 15. Or if you know any other simple ways to not have to go threw the trouble of making a box.

I'm currently building an enclosure for 1 Fi BL, (15") and I was wondering, which box will better suit the sub, (both will be tuned to 32Hz). 4cuft 4.9cuft See signature for car and current setup info. Thanks

I have been searching around now for a good 30 minutes on how to figure out the bass in a song. I know you use some program and play the song through it. You then select a little bit of the audio stream and analyze it somehow and it will show how low the bass gets... (I am trying to figure out the bass line in song. When it drops to the second lowest, I have never heard my car rattle so much nor my woofer get so loud. The first bass "hit" is at 34.5 seconds. And the bass hit at 37.5 seconds I need to filter out. I see the speaker move for it but cant hear anything)

I want to do IB in my 1995 Acrua Integra hatchback. I am aware that I need to seal off the front wave from the rear wave but how much so? If you have seen the rear hatch area do you have any ideas how I can acomplish this. I was gonna remove the faux rear deck and put up a wood deck to mount the woofers and then seal off the seat area. But there is the issue of plastic paneling...do I need to remove it all? and then there is the issue of where the deck will touch the hatch. I cannot seal it together because I need to be able to access my trunk. Any ideas?

i've got a sealed box for my rl-p's. its built into the well of my car and is a major, major pain in the ass to take out of the car, or i would just pull it out and feel for air moving at the joints. when i push one of the speakers in, the other will push out, and very, very slowly settle back. is this normal or does that mean there is a leak somewhere?

I'm just curious what are the advantages and disadvantages between TL enclosures, 4th order bandpass, and 6th order bandpass enclosures. These are all very new to me!

Got bored looking at the new sub in the cardboard box from Fi and then i though duck tape and all hell broke loose!!!!

So, my daughters MECA Power Wheel got a broken port... So I decided to rebuild... The small sealed enclosure was practically free airing so I was looking at making a loading wall, but I don't know how to tune for just a loading wall which got confusing because it started coming out at a 6th order... So I started looking into 4th order, sealed one half, ported other. plenty of loading surface, as well as the output for the port to under the dash for the kick score. I have it as .35ft^3 sealed side (its a single 8 sealed enclosure is .25-.5ft^3) and ported side .68ft^3 with 2 2" aeros 10" long at 45hz. still fits on the back of the power wheels, and tuning a little higher f…

Alright, so I'm planning a build for my S10 reg cab, and need help designing the box. It's going to be 2 SA-10's in a 2 cu. ft box net, ported, tuned to 33-35 Hz. Also powered by a SAZ-1500. My max dimensions are 50"L, 22"H, 9"D bottom, 5"D top. I made up a box using the torres box calculator, but I was having problems with the port. I'm planning on using aeroports, but they were needing to be too long for that tuning in a small box. Not sure what diameter, and how many I would need. If anyone can help me out I'd appreciate it!

I picked up a btl d2 for 250 tonight, and have it in 4 cubes at 32 hz. I need a box to really let it shine. I was thinking 8cubes @ 30hz. I am unsure of how much port to have though. Most likely a slot. My question is what is a good rule of thumb to go by for port area? I've heard mixed things about the 12-16in/cube rule.

edit denim: temp. removed due to non members leaching, not cool but huge props to shane for being nice enough to post it up for us

For those of you that have pondered about getting a sponsorship and dont know how, or some of you that think you deserve one, here are a few helpful hints. #1 Accomplish something. Are you a nobody? Have they heard of you? Do you get noticed? #2 Sell yourself. If you cant sell yourself to them, how are you gonna sell their product? #3 Hold your tongue. I can guarantee you that there isnt one company out there that will sponsor a loudmouth s.o.b. that just makes negative scenes in public or on public forums. As a sposored competitor, you are representing the company. #4 Make a game plan. What comps are you going to? Do you show off your ride or just put a blanket…