SPL & SQ / Fabrication

im lookin to start a new build and try doing a wall. i know i shouldnt be doing this myself but the only way to learn it to ask a ton of questions and do it yourself. im not sure on the best/proper way to safely secure a wall. the walls gonna be for 2 psi platform 3s which arent too light. i just dont want the wall crushing me if i ever get into an accident. thanks.

I was wondering if i could run two rl-p 18's in only 7.6 cubes sealed after the sub displacement. Sounsplinter suggests 4 cubes for each 18, so would running them in a smaller box not be a good idea?

What would be considered too small for a round port (in terms of diameter)? I'm trying to design a ported box (0.7 ft^3 ~ 24hz) w/ round ports for an RL-I 8" and the only diameter port I can use w/ a reasonable length is less than 1.5"...won't this create noise? I just can't imagine using a 1" port for that monster... What's the rule of thumb y'all?

i got a box that is 40x32x17 and trying to tune it to 32hz can someone help me find how big i need the port hole

Alright, i was suggested to use the recommended xcon enclosure (7.65 tuned to 30) but sub up and port back apparently is better in the jeep grand cherokees. All i did was move the sub to the top, will this work? Will it load strangely with the port? Or should i just design a new box lol. like so

I've thought about doing this and recently seen someone actually use this method but never commented on how good it was. In instances where all-thread cannot be used.. how about running those flat steel bars that Lowes sells on the inside of the box? Those are humanly unbendable.... it's steel. I was thinking about running those, gluing them to the box, drill out contact points, maybe 1 every 12", run bolt through to the outside, threadlock it and use a large washer on the outside of the box with a nut of course. Seal around the steel bar. These bars, if i am not mistaken, are only like 1\8th" thick. Shouldnt' that make the wall it is attached to hella strong? I see n…

can you do a 2 or 3 way active set up with this equipment? (Alpine CDA-9884, PXA-H100, KTX-H100) im doing a 2way and will try a 3 way down the road so id like to get something that will have the processing for the 3way when im ready crutchfield has that trade in (exchange) system were i can get a gift card for there site. (im going to sell them my sony hu and old ipod for a like $100). the alpine hu is currently $170. im trying to find a better deal on the PXA-H100, $150 is alittle expensive and i think i can do better. the h/u will be new w/ warranty. so im going either this route or that clarion h/u. with the mic and everything on this combo it would seem that my firs…

Hey guys, Currently in the works of trying to figure out a box that will work with my Zv4. Here's some info: - Going in a 2000 f150 ext cab in place of the smaller rear seat.- Using my Saz-2000D amp- Sundown Zv4 12, suggested 2.25-2.75 cu ft- Wanting tuning around 30hz-32hz- Max Dem: W: 17 | D: 18 | H: 26 or so |- Would prefer sub to fire upwards.- I love rap music and bass heavy electronic similar to white clouds from decaf or lights from bassnectar. Here's my original box and design: http://imgur.com/a/WqOOl No sure how well it'll work and if there's enough port area. So here's another very similar box with a couple small changes that move me from 14.85 sq inch…

hey, im going to be buying a VW rabbit in a couple months cause i got accepted to my #1 choice university!!!! i got a scholarship so now i have about 10 grand saved up plus i'll take out a student loan and im gettin paid to go to school (1600 bucks a month). I currently have a Fi Q18 tuned to 28-30 hz, and i hit 145.2 on my first try with some music. Im looking for some help on deciding what the best setup would be for a hatchback. Im thinking 2 12" BTLs with about 5000 watts. im really excited to get this project goin. my goal is to break the 150 mark but music is what the stereo will play, no farting. any help is appreciated!!!! thanks

I just got a 12" Mag from Low-Hz, and currently have it in my old sealed box that housed a JL 12w6(v1). That box has about 0.8 cubic ft. after driver displacement. Anyway, I was planning on building a ported box and got this off the net: http://www.subwoofertools.com/forum/ported...=&Vas=&Fs=&CE=0 I was all set on building it, but decided to read more, and the more I read, the more I get confused and hesitant. So I decided to ask the official SI site for input. I want the best ported box with a maximum width of 30" and max height of 13". It's going into a 95 Ford Mustang, and I would like the box to fit perfectly into the hole when you fold down the seats. …

I need a box for two AA Mayhem 12s, and Ive got the external dimensions, trunk dimensions, port lengths and everything. I just need someone to build it because I am in the Army Active duty living in the barracks and I cannot build a box, I need to order one. Please post if you know if a website, or if you know of someone that can build me one. Greatly appreciated guys!

So my brother keeps telling me that even if i port my box that it will have no effect on how loud it will be, because it is in a trunk and that the only way i will tell teh diffrence is if i have a suv or fold down seats I know this is not true, but to an extent it kinda makes since

Ok I owed a freind of mine some money so he asked for a box and retarded me i said ya lol so here we go. It will be a bit different decieded for free i might as well do something different try something new. 1 cvr 10 1.8cubes tunned to 36hrz with an external port 28sqin.. design will be up in a bit and box will be bedlined

hey so is there any one here that can desgin for me a ported box. If you can design it, tell me and ill send message you the information for for demnsioins

Live in Texas and the temp can range from 95 to 105 from May to middle of September. Just want know how to keep my amps cool from running and the temp being so high?

Hi folks. I just picked up a pair of L7 10's to go in my single cab 06 Sierra. I would like to go ported if I can make it play loud and hard enough over a sealed setup to be worth while, however I am not sure as to what my best bet would be in terms of porting for this. The enclosure dimentions will be18"Hx57"Wx7D which is good for 2.91 cubes if my math is right. I've been running 1 12" powerbass L12 in a 2 cubic ft ported enclosure with the sub behind the pasenger seat and one 4" port firing up from the top on the oposite end and it has sounded pretty decent, but I want to run more power and get louder and due to mounting depth issues a more substantial higher power ha…

I'm designing a box with the help of the torres box calc and sketchup and was wondering if anyone had any suggestions or if this looks right. I believe I included all necessary dimensions, but if I forgot any let me know. The subs will be mounted on double baffle up top, with rear facing port. Any help/suggestions/comments are appreciated!

Hello, im building a box for a loaded 12 btl. i have an odd shaped box i made to fit under my silverado back seat. my question is how should i run my port/s. the box is wedge shaped with 3.6 cubes gross. the box dimentions are 11.25 high in front 8.5h in back 53.5 long and 16 deep. any idea on port location? trying to get 14 sq/in of port per cube seems hard. thanks steve height1 11.25" height 2 8.5" length 53.5" depth 16" the sub will be facing up on the drivers side

Ok, so i have the planned dimensions and i need help calculating the port and seeing if this box is ok? Two Alpine type r 12's will go into it facing towards the roof of the vehicle. Length (Depth) = 26" Width = 37" Height = 13" So what should the port calculate to? According to the re box calc. they say the port length is 34.75". Is this correct? I'm usin .75" MDF of course.

Who's Going,? im not, ill be in Key West, but if there is enough interst in the people who are we can have an SSA meet prior to SBN. Kickin', i know you are going, stop by my house on your way so i can hear 150 Certified on TL.

Would it be a good idea to cool your coils down to less than 0*C before your SPL run. One of the ways i have thought about would be to spraythe duster cans upside down int the pole vent. Only problem i can think of is if you got alot on the spider. Lower temperature means lower resistance which means more power.

Hey there! I need serious help building a ported box. Ive never had, nor built a ported box and i want to see for myself what the difference is. Ive tried every different box calculator i can find, but im sad to say there a little too complicated for me to understand. Im a rookie when it comes to car audio specs. Im a pro at listening tho lol. I want to learn more, a lot more, but everyone close to me dont want to teach, they want to charge. i could easily build a sealed box, but i really want to port my subs. I have 2 lethal injection 12's. I need 4 cubes, 60 square inches of port and i want it tuned at about 32hz. Space is not an issue. I took the back seat out of my ra…

okay, so I drive a 1995 honda prelude. I just got my nightshade 12 about two weeks ago =], I am running it with the saz 1500, I have also done my big three. I feel my nightshade isn't at the full potential but, it could just be my box. Off the top of my head I can not tell you my demension, all I can tell you is that its 2cuft at 33hz. I am planning on building another box very soon. I would like to know what input anyone has on they're 12" nightshade and there boxes and how they sound, also anyone with a prelude and where the have there sub mounted and the port faceing. Thanks, Jordan

So I drive a f150 ext cab with a kicker cvx 15" with a 6 cube box tuned at 32hz. Right now it is powered by this POS sony 1200 2 channel. The first time I metered I did a 139.5 door open. I metered yesterday and the best I could do is a 137.2 The testing was done on a term lab. Now the things that changed: 4 ft shorter power wire than before - better bigger ground - better new rcas - better new bigger remote - I know this wont change anything just thought I'll throw it out there The only difference than before would be the temperature. It is roughly 35-45 degrees hotter outside now. Can the ambient temperature effect db?? Also my buddy metered too and he had a decrea…

Hello everyone, This is my first post.I currently have 2 dd9518g dual 4 ohm subs,1 hifonics sampsom amp driving these subs in a 12 cft box ported to 35 hz with 140 sq in port. this system is in a 2007 chevy avalanche with the midgate removed.I currently hit a 149.5 db @ 47hz. I have 24 cft avaliable for a new enclosure for the new season and would like to try a bandpass box.This is a daily driver so i cant make any major mods to the truck.The truck have 2 layers of dynamat on the doors,roof floors and bed of the truck.I currently have a dual alternator setup with 6 kinetik hc1800 batteries for a electrical system.Believe it or not i also use this vehicle for sq also.I am …