SPL & SQ / Fabrication

I am designing my wall in my 95 Lumina, It is a four door Sedan. The wall will go up to the front seats. I was planning on making the port on the drivers side Vertically with two 18's like so On the other hand my father said it would be better to do the port on the top or the bottom with the woofers above the port. Is this true?

I'm planning on building a wall in my Lumina, I'm in need of a design. My set up will consist of 1 DC power engineering 270 amp alternator,~3 deka intemidators, 2 Audioque HDC3 18's in a 12 Cuft wall with a removable port tuned to 38 for daily and higher for comp. Lastly to power the subs a Sundown Audio 3000d. here are some specs with pictures included. Pictures w/ measurements Height: 37 in Width: 29 in and at the curve 38 in from the hump to the roof is 38 in 33 in from rear deck to seats 46 in from bottom of the floor to the ceiling 55 inch from door to door More pictures (P.S. I know my carpet is dirty. M5 already made it apparent)

I was wondering if anyone new of any good enclosure design programs, the only one i know of is term pro. I was just wondering if there were any out there that were better. I am trying to do some experement ing with some bandpass enclosures.

I am wanting to try building a enclosure with a flared port and was wondering exactly how to do it if anyone can help with this i would really appreciate it.

I decided to do my blazer in the dark knight them the sub box is going to be the batman symbol the amp racks are going to be the joker playing cards. I need some help in deciding what to do the door panels and battery and distribution like to go with the theme using to svr batteries and and 2 sets of kenwood excelon 6.5 componets in each door.

Alright so my box is 5.38 cubes internally after the displacements besides the port. Im using a tube port thats 8'' diameter and I want to tune to 32Hz. My box only has about 20 inches of height to work with inside, so some of the port will be sticking out the top. I want at least 4 inches between the port and the bottom of the box. If anyone can help me calculate it out that'd be appreciated.

Which enclosure do you prefer and give your reasons for sayin so. Just trying to see who likes what type of enclosure the best. Me i am kinda in between you can get a good all around sound with sealed, given enough power to run push it. I used to use a lot of sealed boxes because I really didnt have the room for ported boxes given the subs i was usin. Now I have switched to ported since subs now work in ported enclosures the size of what the old sealed subs used to work in. Also which one do you think handles ungodly amounts of power better.

I just had me a crazy Idea just wanted to get some feedback on what you guys think. I have a 95 eclipse that i have been contemplating on how to build this thing. Then it hit me, why not fiberglass a 10 in each door panel and flush mount the amp there as well. Tell me what you think.

hey so is there any one here that can desgin for me a ported box. If you can design it, tell me and ill send message you the information for for demnsioins

I need help building a wall in my 95 lumina, i don't want to pay 1 grand for a wall that i could build myself. Does anyone near Kansas city missouri know how to build walls? and willing to help a fellow SSA member?

I want to tune low for my nightshade 18. How big should the box be after displacements? Port area? Tuning? Thanks!

should i face my subs and port into the car or both to the rear. these are not the only two options but im looking for the best way to get the best sq for a daily driver.

I build ported boxes on a pretty regular basis using the re enclosure calculator and they are always slot ports but i want to build a different box that uses a square port that isnt a slot port but I dont know the formulat to calulate the port area or convert the round port to a square port can anyone please give me some insite on how to do this please thanks alot .

Do you guys take this into account (from the JL box building page): I take this as meaning I subtract half of the port width from the length. For example, my calculations calls for a 16.5 x 6.15 x 26.25" long port in order to tune to 33Hz. Does the physical port in the box then become 26.25 - 3.07= 23.18 inches long?

Hey quick question: if im looking for say 33hz from an areo port in a box 3 cubes how do i calculate it if i need two ports? heres the situation, i have box 3 cubes, want to run 4 inch ports. if i make one port its 7.4 inches long but i need more area than that.

I am looking to build another box but want something unique yet efficent. I'll pay for the design. Some specs on the trunk: Cannot be over 14" tall x 20"wide x doesnt matter too much over 40" deep. The box will be for a 12" btl loaded off 2 aq2200s. I would prefer tuning no higher than 32hz. Lets see what someone can do.

im converting 4 3" round ports to 1 square port. i made a 4x7 square this just seems smaller then 4 3" round port... please help.

Hey guys I have all of my equipment just wantin to see if anyone here has experience with ext cab trucks. I have 2 Kicker CVX 15's goin in a Dodge Ram ext cab and I'm going to port them just can't decide where I need to face the subs and port. Can anyone help?

So after taking a bed apart a few days ago i discovered the mass use of MDF used in the bed's structure. Now if i wanna build a box for my 18" btl, people always say use 1/2" MDF. How important is that 1/2" ? Why does it need to be that thick? For structural/support reasons? the MDF from the bed is 3/8" and i'm going to go buy the 1/2" just because everyone on here says to do it and i trust them, i was just curious. I have like...50 square feet of the stuff.

I have a ski port with a latch/door that folds down into the trunk to allow air to flow through. If its ported through the hatch, and otherwise sealed off from the cabin, would that yield higher spl would it be a waste of time/money? Im not looking for pure spl, I just thought this might let me keep my sq but make it a little louder. My current setup is a regular 2.5 cube box with a bunch of room around the top/side to get around to the back of the box and through the ski port. Here's my idea(s)..... And sorry that it looks like a third grader made these sketches.. its all i could do with ms paint.... side view of trunk shape with ski port door open/folded down loo…

first off i am not mister know it all so please bare with i do know a lot but will see . but any ways what is it with resonant tuning frequency? would it be better to tune low as possible for like a t line and get a higher score? unless your talking frequency length. the lower in the octave you got the hard the bass hits right ??? with in reason of course like the sub dropping off and just can't play well at 18 hz were it plays better at 47 Hz etc etc ... because the music energy is reaching the mic at it full potential of 47Hz if you tune to high the spl drops off again so you lose power in the spl right??? so why would you look for a resonant frequency like 18 hert…

Hello, im building a box for a loaded 12 btl. i have an odd shaped box i made to fit under my silverado back seat. my question is how should i run my port/s. the box is wedge shaped with 3.6 cubes gross. the box dimentions are 11.25 high in front 8.5h in back 53.5 long and 16 deep. any idea on port location? trying to get 14 sq/in of port per cube seems hard. thanks steve height1 11.25" height 2 8.5" length 53.5" depth 16" the sub will be facing up on the drivers side

So i have decided to build a custom box for my 2 10in type-s alpine subs. I found an equation on JL audio's website to tune a box and have been playing with numbers for about an hour now. Everything looks good to me i just want to have someone double-check to make sure im not screwing things up. The outside dimensions of the box are 11.5X31.5X20.5in. Using 3/4in mdf that would leave me with 5700 cub inches inside to work with. there will be a single vent, 10in tall and 1in wide, going in 5.5 inches. after subtracting the volume of the 2 boards used to create the vent and the 2 subs( 86.4cu in each), ill be left with roughly 5444cu in of internal volume. with the equatio…

Im looking to make a box for 2 12inch kicker l7s. I want the subs to have individual chambers and to face up. I want to use aero ports and have the ports facing back. I want to use 3/4 inch birtch plywood. I am having trouble to come up with a design. I want to tune it to 32hz. I am looking for help with this design and I am looking for opinions on what I want for this box. I want it to be loud with little distortion. the width of the over all box cannot exceed 40inchs and the depth of the box cannot exceed 24inchs.

Hey everyone, So ive desided to build my first sub box and am pretty much lost. I have 2 10" Alpine type-s subs being powered by a MRP-M500 alpine mono-block. At the moment i have them in a pre-fabbed folded horn box and just want an upgrade. On the Alpine site, they list the"optimum" vented box's stats which are tuned to about 36hz, which sounds good to me. So..... Would it work if i built 2 seperate boxes that share a single wall seperating the two? If i did that would I run one vent for each side and keep all the stats for each box to alpine's site? Ok, this question is confusing me just thinking about it so if it doesnt mak…