SPL & SQ / Fabrication

I want to try out a transmission line box or quarter wave, whatever its technically called, and want to know if im off to a good start... I want to use a 10" Fi BL Dual 1 so 41.5fs with an sd of 310cm^2 = 48in^2 1130/41.5/4*12 = 81.7 inches... so my design looks something like this... I dont know much about these kind of boxes it just sounds like a fun project, If it turns out horrible I only lose a few hours and a little off my wood stockpile...What do you guys think about this design and these measurements?

Im about to start building a tube out of MDF for a sub box, but before I needed to test things out to see if I could. I also decided to take pics of it for a little tutorial if other people are wondering how to do this. I started of by finding the inner diameter I need. Im going to use this for an 8" sub with a 7" cut out. so my inner diameter is 7" Now outer diameter: I'm using 3/4 MDF so my outer diameter is 1.5 + the inner diameter' 7+ 1.5=8.5" Now I can find out how long I need to cut my board: take the outer diameter multiply times pi to get the circumference, which will equal the board length: 8.5 * 3.14 = 26.7" Board length is 26.7" Now I need the inner circumfere…

so within this next week i plan on getting an Fi Q 18 with the BP. Itll be powered by my elemental design nine.1 (and from reading through these forums, noone seems to like ED, but this is the amp im sticking to) and im guna be wiring the sub down to 1ohm. my enclosure is going to be in the ballpark of 4.5 cubes in my '01 extended cab ranger...but this time i want to go ported, and this WILL be my first ported box (and my 4th setup period) i want to do aero ports, but im still having a hard time trying to figure out how to get port dimensions and etc. and idk what to really tune it to either....i guess around 30hz or so and if it helps, i listen to rap (and country, but t…

What is the minimum number of yellowtops needed to run a Sundown 3000d? I've still got the stock alternator in the Frontier and want to see what I can do. BTW the Opti 50C is up for sale.

So last time I entered an spl I tied a guy with two 10" solo x's and a rockford fosgate t3000, and there's another in 2 weeks and im sure he will be there. I dont want to risk damaging my sub by upping the gains or voltage any more than i did last time, but perhaps i can adjust the box/ place it in my car differently? The box is a little over 4^3 at 31, and it is about a foot back in my trunk facing into the car. Only ideas i have now are putting 45's in my corners to help flow and raise tuning, and face the sub towards the trunk. Are there any little tricks anyone knows about to give me just a .1 or .2 db gain?

so ive never really found a concrete answer to this, but for sq is a smaller or larger box better? my 15 fi q is in a 4^3 box it is very peaky down low, with kind of weak higher bass(by higher i mean 40-55 not like midbass), and fi says 2.8-4.0 is good. my brothers 12 fi q is in a 1.8/1.9 ^3 box and it says from 1.8-2.5 and it sounds amazing and even from LOWWWW to pretty high. im assuming the smallest recommended box is good for sq/evenness, and the largest is good for spl/peakiness? (I think i just made up words!) oh btw we are both tuned about the same(31 for me 32 for him)

think this is a good stasrt for a moderate sq set up i have a kenwood 6019 indash focal 165 6.5 v2 pollyglass componants focal 6.5 pollyglass 2 way coax. kicker zx1000.1 kicker 350.4 an 2 re se 12's subs. im thinking of swaping amps out to something more powerful but is this a good start?

I was wondering if the port calculater on the carstereo.com page was worth a poo? I used it to build my explorer (8 kicker comp 12"s and a 2500.1) as that worked out perfect......but i used it to build my 4runner (2 hk802sx amps, and 4 SSD 15''s loaded) and it doesnt impress me at all....so i think i figured out why.....here is the link to the page http://www.carstereo.com/help/Articles.cfm?id=31 But here is my real question...when you are calculating your port.....and you punch in all your factors and the end result tells you how long your port should be.....Does this program already remove the port displacement? Im assuming it does since you have to figure in your tota…

Are there any pros and cons of having ports firing: the same directions as the subs, 90 deg off the subs, 180 deg off the subs?

Hello This is my first post here, I made a quick look ,it's interesting forum. However I want to ask about the specs of the SQ system and components? I have Car PC controlling my sound system which is: Car PC with Turtle beach and Creative Xmod USB sound cards. Rear - Infinity Reference 9613i 6"x9" 3-way car speakers Front - Infinity Kappa 63.7i 6-1/2" 3-way car speakers Amp - JBL CS60.4 4 Ch 240 Watt Full Range Amplifier what do I need to add/change to have SQ system? thanks

What is the best way to determine the frreq of a box? How do you calculate the Hz it will be tuned to?

what is the best battery for street A. 650cubic in or less. from what ive found the nsb75 kinetik hc2000 and powermaster d2700 seem to be at the top. what bettery is the best and how much better is it than the others. if anyone knows of another incredible battery im missing let me know.

I've got an 15" Audiopulse Axis running on a Sundown 3000, Ive got another Axis that should be here tomorrow. I was thinking about making a sealed box for both of them, but I dont know whether to do a common chamber or separate chambers. What are the pros and cons of each?

New high for music out of the GP 148.3 30 sec avg pr of 10's! :clap: 150+ playin music comin to a lane near you! I workn on becoming the only Trunk vehicle in the states runnin n the 149.9 class with a tiny pr. of 10's!

I finished my fiberglass box yesterday for 1 15" icon yesterday, kinda anyway. Its a little on the small side at 1.8 cubes. I plan on adding some polyfill to bring it up to ssa's specs for 2-2.5 cubes. I just dont know how much to add, I have a 20 oz bag of polyfill at the house. Any advice?

i have 1K on two Fi BL 12 rear firing in the trunk. would putting a hole in the rear deck improve SPL?that in the cabin will it cause problem for my 6x9 on the rear deck??? what the best way to do it?? Thanks Inadvance!!!!!

Okay, it's about time to put my Sundown SAZ 3000D to good use, I've finally settled on subs, they are Crossfire XP 15's that I will get for super cheap and they are high quality subwoofers: http://crossfirecaraudio.com/htdoc/cf_m01_product_05_xs.asp#. I have some dimensions worked out, I used the SSA Box Calculator and I believe it's all worked out, I just need help bringing the calculator measurements to life! http://www.soundsolutionsaudio.com/home/in...int=1&page= Can someone give me a hand on how to put that on paper so I can build it?

does anyone know the t/s parameters for an oz matrix elite 12.2(dual 2 ohm voice coils) since i can't find the bl or sd measurements anywhere? and from your past experiences what enclosure size,port and tuning is best recommended for maximum street bass?

i have a box with 4.4 cubes after sub. it has 2 4"x12" ports can some one tell me what it is tuned to please

I need help mainly with the port calculations for a 10 cubic ft box and a 20cubic ft box This will not be a chambered Box I'm "not sure what size cubic ft box I'm gona build yet" So if you have a formula that can figure port sizes that will help allot this is for two BL 18'' subs. I can build a box just need some help with this. Thanks

I know some of you would prefer to put a JL w6v2 in a sealed box... (I'd like to go that rout if I had two subs and a powerful enough amp to push them both), but since I just have a single sub and amp I want to build a ported box. I want to make the box wedge shape so I can get the most out of my trunk. I did design a box using a 4in round port, specs: Sub is a single 12" JL audio w6v2 3/4" mdf box external lengths: height= 14.75in width= 26.0in bottom depth= 13.5in Top depth= 8.25 in 4in port, tuned to 32hz Net volume, 1.5 cu. ft. Final internal volume after adding in sub and port displacement ~1.76 cuft. I've been hearing from alot of people that I should make…

so i still havent gotten around to doing a new box for my bro's L7. but im thinking about trying something alittle different. he basicly only wants spl so im thinking about trying a wall... i have to build the box in the trunk anyways so might aswell try something new. its a mercury sable by the way. im thinking 6 cubes net design from the manual or do a tuning around 34hz...? we are prepared to deaden the rear deck, etc. will there be more output from a wall in this car or would it be a waist of time? if we did the 6 without the wall there wont be much of a trunk left anyways... and im sure we can seal the trunk off from the rest of the car effectively.

I have loved my 18's since I got them, but due to a baby being on the way, I have to get rid of the 150 pound 12 cu.ft monster in the back of my little XUV. I'm replacing them with......(drum roll please)...... A pair of Critical Mass UL 12's! I hope to god that they fit the bill for me output and soundwise.

Hi, I have been using fiberglass resin in my boxes for years Does resin help spl because the box is harder or does the resin help with the sound wave, maybe the speed of the wave.I just want to no if I need to resin or not .My spl numbers or the same with or without.Thanks for any help.

Current setup is Mach 5 MLI and Seas H1396 amplified by an Eclipse EA4000 and all the processing is done by my Alpine 9813. I'm very satisfied with the midbass output and the top end, it's just that midrange isn't cutting it After seeing Ryan2's idea with the Fostex FF85k's I thought trying a pair and ditching the tweeters. I don't want to invest in the H701 at this time and try 3-way (would require some sort of controller too and another 2 channel amp, not to mention the extra room ) The problem is placement. I have no room in the dash to mount them. Pics of the "locations" : One idea is to use the kicks. Passenger side is ok, driver's side could work but there's v…