SoundSplinter

Going to be building my enclosure soon for my babys and was wondering should I use 3/4 MDF wood or 1" MDF? They will be sealed 1.5 cubes each powered by a US Amps MD2...

I'm itching for more SPL, I already have 1 12" rlp in a ported box. I want MORE! I was thinking of either getting another RLP or 2 Alpine Type Rs (I've heard they're good for their money). The hard thing is my 1 12" is D2 and my amp is only a JBL600.1 arrrrggggggggg!!!!!Sorry I just wanted to vent!

Well, I have removed all my car stereo stuff to make room for family in my ride...BUT, I cannot part with my RL-p 12..I just love it too much. I was wondering if box sizes/styles would be the same for use in the house? It is looking like I will be starting with around a 200w home audio amp. I know that is way under the RL-p, but I aint selling muh speaker... any ideas/opinions welcome

Not for sure if i will be getting the new amp yet, but its an Elevation audio DX2000.1. I was told it would do 1200-1300 at 2ohm. I am planning on getting a 15" RL-p. So, what do you guys think about 1300rms going to it?? I know it will be fine. So the next question, what type of box should i make sinch i am throwing so much power at them?? Should I go sealed just to be on the safe side??

Just got some time to take some pics of the Rl-p's in the wall.....Just got last amp back from repair so i still have to break subs in......No numbers as of yet hopefully soon with a video to throw up here..... Amp Amps Signed Rl-p from Mike Wall Wall2 Front Side Side2 Back Front1

I am still up in the air as to how I am going to install the little monster. I have wanted one for a long time, now that I have one, I almost want a second one to pair up with it. So I want to start thinking about a very good SQ box with enough output for the bass to make it out of my trunk and into the cabin, which by the way the RL-p 12D2 is having some trouble with an Orion 8002 on it (just to give you and idea as to how much bass is trapped in the trunk). Anway, I looked around a decent amount and listening to Mike, I am thinking I will go ported. Even though I would love sealed but know it will not have the output I need. So according to Mikes measurements, the …

i recently put 2 x rl-p in a 'housewrecker' go too, www.decware.com , look for the speaker page, and then the housewrecker.its a ported design intended for large rooms, i built the 12" version and its in the back of my mini van. the sound is absolutely amazing. if you have a van / large vehicle, and you want incredible sq with lots and lots and lots of effortless output. build it.

lookeyrl-p

how much air does the rl-i 10 displace? i don't mean how much air it can move, but how much volume do the basket and magnet displace...

my first run rl-p ( painted logoless cone) has started to die. it's not dead, but it's on it's way. so i'm retireing it. i guess too many 2500wrms runs in 2.5ft^3 tuned to 28hz. but boy did it sound good down that low and that loud..lol... i'm going to miss it.. but it's replaced, albeit for a short while, but a LA audio x2...at least it's another tcsounds product.. so, do i send it in..or make it a really pretty and heavy paperweight?? wheeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee

due to a recent trade i now have 2 x rl-ps im way more into sq ....L then spl. my favorite box desighn for 2 drivers would be the 'wicked one' www.decware.com, but its desighned for 10s? and im not getting much help with the question, if i scale up a dual folded horn desighn by approximately 1.2 will it effect performace (sq) badly? anyone know a great sq desighn that will get loud and remain true to sq performance? straight sealed in my experience is not as good as a desighn that controls the air movement in fron t of the driver (bandpass, horn etc) help! off 2500 wrms

i have 2 soundsplinter prototype 8s, but i want another rl-p 12, anyone wanna trade?

i'm thinking of building a ported box for my rl-i 10. 0.32cf tuned @ 27hz. it's one of the boxes mentioned on the site. i plan on using a 4" port. flared at both ends. any possibility of port noise ?

I'm running 2 rl-p 12's off of a 1200 watt infinity amp (im never getting an infinity amp again) in about 1.25 cubes each sub. My brother is running a 13W7 off of the JL 1000 monoblock i think its in a 2 cube box. His W7 beats me in the higher and lower frequency bass notes but i do keep up in the lower notes. But overall he kills me. I was really hoping i could just bash up his w7 with these 2 12's. Any tips on how i can kill my compitition with this beast. Yeah I am pretty sure going ported will do it but im not sure if i want to go that rout. THanx. I think a better amp might help because this infinity amp is clipping like crazy.

Hi all, I am in the market for a system and have decided on Soundsplinter...Here's is my dilemma: Car will be 2002 Honda Accord Coupe, and here is what I have planned: HU: Pioneer DEHP9600 $400 Front: Rainbow SLC Kickbass 6.5" Comp 280 Rear Fill: some decent 6x9 100 4-ch amp: PG Xenon 100x4 (100wx4 @ 4 ohm) 300 Sub amp: Kicker zx750.1 300 Sub: Soundsplinter I was gonna go with 1 12" Rl-p w~ 750W after reading many positive reviews from caraudio forum. I want clean, tight, distortion free bass with decent output (used to have a…

Two questions: I was wondering if it is ok to slightly overpower this pair of DVC subs in a small sealed box. I have an MB Quart RAA2400 amp that feeds 400w RMS x2 @ 2 ohms (maybe underrated also..) Also, since my amp feeds 400w x 2 @ 2 ohms, I can wire these DVC 4ohm subs so that my amp sees a load of 2 ohms in each channel... right? Thanks in advance!

Power Acoustik A2400DB or Lanzar Opti 2000D...

Im "considering" getting my front doors redone via fiberglass and setting up a strong front stage. Comps up top, with some RLi 8s in a sealed atleast 0.4cu ft enclosure per door. Depending on the amp still havnt decided if im going to go with SVC of DVC as of yet. Going to give them atleast 150rms per to work with, maybe even upward 300+ should my elec system support it. Upto what freq range would the 8s be able to go upto? I was thinking upto atleast 200hz, still open to debat on what to cross them at. As for the comps, im leaning heavliy towards a set of rainbows...undecided which ones atm. From the looks of things is going to be atleas a 600+ rms front stage should thi…

I'm looking to blow some minds of the ghetto people around here who think bigger is better. I was thinking about running 4 RL-i 8's tuned to around 30hz off of a Hifonics 2006d. I'm hitting 142db currently with a single 9500 12, and would like to at least be just as loud, if not louder. What do you guys think?

with 3000 watts how maany rl-i 10 or 8 would u use ive got about 22 cubes to work with

I got my 12" RLP in a 2.0 cu ft ported box, tuned to 29hz and powered by a RF t5002. This setup replaced my 2 12" JLw4 in a 2.5 cu ft sealed box that was powered by an old kicker ZR240 amp. On certain songs, it has the same "tight" bass I got in my sealed box and on other songs it just seems like the bass grew some balls. This setup is louder and has more visceral impact than my old JL setup. I'm really enjoying it. Only thing better is perhaps a 15" RLP in my trunk, but if went that route, I wouldn't have any space left in my trunk. A great product with even better customer service. Edit: James, a local box builder made this enclosure for me.

Does anyone know when the RL-i8s with DVC will back in stock. I went to buy 1 and it says not avaliable. Thanks, MJ Why an 8 I just have to have one of those bad boys.

My sister wants something louder in her car. Right now she has two JL 10w1v2's in the JL ported box with about 500 watts going to the pair. I don't really know much about SoundSplinter products but I was wondering if a 15" RL-p in a 3 ft^3 box @ ~ 30hz (already have) would be noticeably louder than what she has now. The RL-p would probably be run off a Nine.1 @ 1 ohm. She listens to mostly rap and R&B. The only other sub that has been in that car was a 15" RF P3 in the same ported box so if a RL-p would be louder than both of these setups it looks like that is what I will buy (I know they are backordered but it will probably be about a month before I buy them). A…

I got my RL-p12 to day. Going to put it in this weekend. All I have to say right now is that is one heavy sub. I am going to put it in the same box my 12 SE is in 2feet @ 32hz and see how she sounds. I will build a new box in the future. I have a PG X600.1 to push it. Thats it for now I will tell every one how I like it and I will compare it to the SE12. Same amp same box so all will be equal. Mike J.

How does the SQ of the Rl-i 10 compare to the RL-p12. I know the 12 should go lower. But do the subs have the same sound. I like how my RL-p 12 sounds. I have been thinking about running 2 but with the space I have it would have to be sealed and was thinking about the 10s. the amp I have would be great for 2 10s but for 2 12 I would need more power in a sealed box. I dont think 800w to 2 12 would be enough ported yes but sealed I dont think so. If the 10s sound the same as the 12s I think its a good option. Then use the 12 for HT.I am not letting the 12 go I am keeping. Well thanks for your help Mike J