SoundSplinter

I CUT PASTE THIS FROM ANOTHER FORUM, is1pimp is the reviewer? look like he got what he wanted? Amp is a Nine.1 and the box is a 1.0 cubic ft sealed enclosure. I had the RL-P in it for about a week, and the XXX just got put in today, and here are my findings. These two subwoofers are completely not in the same league as eachother, maybe in SQ they are, but thats about it. The guy that wrote the other writeup comparing the RL-P to the XXX and saying the RL-P almost got as loud, and was the better choice has to be completely insane (no offense to whoever wrote that review ). Or the only explanation is he used 750 watt, and i am using 1200 watts, so i guess before 750 watts,…

i'm coming up with a lot more airspace than i thought i would out of my ta. basically i can make the box anywhere from 2.5 to 3, possibly 3.2 cubic feet, net. (this is sealed) i like deep, low bass as opposed to tight punchy. amp is an elemental designs nine.1. mike told me the sweet spot would be 1.25 to 1.35 net feet, per sub, but i asked the question thinking that i would barely be able to manage 1.25 per sub. so now that i have more options, what do you all think?

NOT!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! well what did you expect?

NOT!

when wireing my voice coils together,i couldnt get 2 sets of 10 guage in the one side? so i went with 12 throughout? any one got any good ideas about how to wire a rl-p 12 dvc with 10 guage? -me

Hey guys, glad I found this place. I'm finishing up an install in my Nissan Titan and I've run into a wall. I've got all the comps, amps, HU, changer, everything except for my subs installed. Problem is my mounting depth restrictions. I have already gone through two RF 8"s (didn't like the sound), a cheap Infinity 10" (not enough) and now I have two Infinity 10VQ's sitting in my living room because their 6.5" mounting depth is going to be nearly impossible to squeeze under the rear seat and still manage enough air space. So I was recommended the SS RL-i 10" by a friend. Its mounting depth should work fine, but I wanted to ask you guys if it will suit my needs. I'm…

first impressions of the sound are sumptuous! will post more as i get more listening time with it!

About how much airspace will an RL-p take up if inverted? Is it basically ZERO (less than .05) or is something measurable? Thinking of inverting these babies, box design pends this question.

i took my box out of the car for a while... can i put just 100 watts to the rlp 15 and will that be ok? or will i under power it and distort it and blow it up? its tuned to 28htz by the way in a 3.5 cube box

Well, the 15s will be here yesterday and I haven't built a box yet. I've got a 4.8 cube NET @ 31hz box that was for my atlas 15...I was thinking of using it w/ one of the rl-p and running it at 500 rms since that is all I have available at the time. How do the RL-ps react to a too big box? Will it be alright sounding or should I not even go through the trouble of rigging it up?? (Rigging it up consists of switching some amps around b/c I don't have an amp for the subs, I'd have to use my SoundStream which on the highs right now, then take my xtant 1.1i and bridge the fronts into 1 channel) Max fudge around time of 2 hours, but j/w if it'll wang at all.

2.03 cubic feet BEFORE sub displacement, tuned to 34 hz, 30 inches of port area. Is that gonna be sufficient to get me the output i want, as well as still retain a good amount of SQ?

okay i was messing around with the info yall gave me for tube ports and i came up with this: now is it okay to have the 2 ports on the opposite ends of the enclosure?

hello all, i figured i'd join this forum since it's the official SS one . my previous setup consisted of a 12" brahma in a 2.5 cu ft box tuned to 28 hz, power by a bridged fosgate power 451s amp. next setup will be this 15, in a 3.2 cubes box tuned to 28, powered by a arc audio 1500-xxk on to the pics! thanks again mike! the sub drawfs the ruler

Would a viper 1200.1 wired to 1 ohm be better than a pg tantrum 1200.1 wired to 4 ohms? Which one rates there power at a lower volt? I would probaly get the pg used and the viper new.

well I had my heart set on the new LMT soundsplinter subs and I wanted to get them as soon as they came out SOO BAD!!! but another offer came up and I wanted to take advantage of it. as many of you have seen on the realm of excursion site the sub that I recieved. sorry mike . mabey in the future I'll get some SS subs because my love for audio wont die. anyways since i made this post i thought what the heck why not take some pics of my LMT sub and the vid heh http://www.realmofexcursion.com/videos/TC%...nds/lmt15.1.wmv but im not takin the soundsplinter.com off my sig i wanna represent a good company

apparently there isnt enough room for a ported enclosure for my 2 rl-p 12's in my 87 trans am. i'm putting them in the well facing straight up, i THINK this will sound the best. thing is i havent built a box in years, and i only helped with a simple sealed box for a trunk, this one will be a lot more complex getting it to fit snug. i've got an elemental designs nine.1 amp, and i think the 12s should be right in their sweet spot with it turned up all the way at 1 ohm, right? they're d4s. i want as much space as possible right, and separate chambers for each 12? http://thirdgen.org/techbb2/showthread.php...threadid=306257 here is a design for a generic sealed box that was …

Ok, here is my rl-p that I got a month+ ago from the group buy.. just kinda never took pics and was busy for the last month so thats why it is STILL sitting around a well I masturbate to it, better than porn. the sub and my djembe blurry my ride

Okay, so my friend just got his ava 18 installed and its purdy loud, I've liked what I've listened to so far. Its on about 1000/1200 RMS. My question is, to get louder should I.... Get an MT 15 ported on 3krms or Get two Rl-p 15s ported on 2krms Also, its pretty much a given that either of those would be louder than his 18...wouldn't ya say? Propsed box for the Rl-P 15s is a true CRX style box, two chambers, subs up, ports back, 2 4" aeros per chamber, 3 cubes net each tuned to 34hz I dunno, when I think Dual 15s CRX style in a hatch...I think LOUD. Thoughts/opinion/ramblings. Just respond...I'm tired...intoxicated, and about to pass out. Yet I still post...YOUR TURN

*sorry for another amp question in a row i just got my RL-p15 in yesterday, biult a 2cu. ft. sealed box and ran it temporarily off an Alpine MRP-M350 amp. i had to drive the amp close to clipping for the lows to come out, but i know i was badly underpowering it. im planning to go ported once mike gets back to me on my ideas. i had these amps in mind: Alpine MRD-M1005/M605 maybe Rockford T10001BD MTX 801D PG Octane R 8.0.1 I really want to spend less than $350 though i know some that i listed are over that. any help would be appreciated. thanks

i swore to myself yesterday that i would 'leave the system alone' for a month,to fully appreciate and give it a chance. but less than 12 hours go by and im wonderin,if i threw a box on that baffle ???? new speakers in the doors? deadening material/hood/firewall liner?........i will not touch it for a month...i will not,no no no!!!!.........must sleep..... stop thinking bout the sounds......notice wife........perhaps just the door speakers?....

this is what i got in a g35, i believe stock alt is 90 amps: xenon 100x2 zed deuce 800x1 rl-p d2 in 1.35 sealed box. finally installed my rl-p d2. and i just love the way it sounds. problem is... when i turn the volume halfway to where i want, my lights starts dimming already. i'm like wtf! my '91 mazda minivan had a better charging system! i may have overshot a little by buying the zed deuce, but i didn't think it would be this bad. i'm so pissed i bought all this chit and can't even use it to its potential. i've read that replacing the big 3 will help...but how much really? i'm thinking of maybe porting...or worse, having to go with another brand that's mor…

LINK

just wondering, but i always used to fill the box with pillow stuffing because (from what i was told) helps out the sound. is this true? and if it is, i'm getting the rl-p's in a ported box. it's gunna be one chamber with two ports. would the pillow stuffing do any good in a ported box? thanks

would it be silly to put some clear nail polish on it to protect it do it does not fade or protect it from scratches? just a silly thought

check out my plans: i decided to go round port cuz one, its soo much easier to calculate and make, and 2 its easier to fire it into my cabin (the port will be positioned right underneath my first aid kit space). the reason why the sub cutout is so high, is cuz i wanna make a false floor for the amps, and this way my sub box wont tip over ~2.0 tuned to 31 will be okay rite? i need opinions