SoundSplinter

does any one got a 15 sitting around (or any TC9 for that matter)they could measure for me. i'm trying to draw up a new box and its gonna be a tight fit :up2somet: so what i need is how far down does the basket come? you know the spoke that comes strait down. how wide is the motor? and mounting depth? i think i can get this one, but just in case.

i got a good one today i sealed the port from the inside...so i now have 5 cubes sealed http://www.realmofexcursion.com/vid...ter/rlp15.6.wmv

Hi everyone finally ordered my sub... see this thread http://www.soundsolutionsaudio.com/forum/i...?showtopic=2502 my amp is a 350Watt Rythmik audio plate amp the sub will be used for both HT and music 50/50. I wld like a ported box tuned low. BTW, 4" ports are quite hard to come by in my country....is there likely to be chuffing if i use an ordinary piece of PVC piping regards

i have one Rl-i12 sub and i'm designing a vented box for it in program called 'Bassbox'. i know vented enclosure is not recommended for this sub but it won't be run with more than 300-400watts anyway. oh and this box won't be used in a car but at home. so now i'm not sure about the size, volume of the box. the same is with diameter and length of the vent. well i want to know what would u recommend for each one of this exemples individually: 1. what would u recommend for BEST PERFORMANCE of the driver? 2. ....for low tuning. ap. 22hz oh please tell me also what do u recommend for car box (i will probably build one later on...). that's it... size, volume etc... thanks, Pek…

Hey everybody, since I haven't had time to completely revamp our product pages as I am planning on doing soon, I figured I'd post some images of our new cosmetics since we have started shipping our fully black annodized aluminum coned woofers. We will henceforth be producing our entire inventory with these entirely black annodized aluminum cones, with the exception of the new RL-i8's, which will continue using painted aluminum cones (black on the front, silver on the back). Enjoy!

which box (in your opinion) would be better suited for my 2 RL-p's? a 5ft sealed or 5ft net ported @ 36Hz? listening to my setup for a while (ported@36) i noticed that it peaks alot more than my boxes tuned @ 30 and i'm kinda missing my LOW notes. if i tune the ported box lower, it will drop the net lower than 5, with recommended at 2.5/per i dont want to go lower than that. so what do you think?

would this amp over power 2 of these

i got my 860 installed yesterday...man this thing is incredible. i sat in my car today for 3 hours just adjusting all the different settings. it is amazing the notes that i never heard before. the subs and the front stage blend so well together! anyway, here you go mike...... i knew that logo-ed sub would come in handy

Yes, after an ENTIRE day of waiting it arrived Don't you jsut hate those long waits. I can't wait to get it installed and finally hear what it sounds like. All I know so far is that it is sexy as hell and soundsplinter has the best customer service ever.

Hey. I just ordered an rl-p 15 and now I need a little help designing a ported box for it. After talking with Mike, I have decided to go with 2.5 cu ft net tuned to 28 hz. I would like the box to be about 30x17 1/2x??? Also, mike recommended somewhere between 35 and 40 sq inches of port area. Thanks. Eric

Ok well ive pretty much decided on getting a single 12" RL-p i will most likely go for the dual 4ohm coil config, but what im having problems deciding on is what amp to buy and the best size box to build for it and weather to go sealed or to port it. im pretty much open to anything but have roughly a $200 to $250 budget on the amp. Thanks in advance, Matt

http://www.soundsplinter.com/images/videos...-RLi10-porn.WMV The above video was taken in low light with a camera I'm unfamiliar with. Hopefully in the future I will master that damn camera and get some clearer pictures up here. The woofer in the picture is running in a sealed enclosure with another RL-i10, off of a bridged Pioneer amplifier feeding each woofer approximately 190 wrms. The volume on the Pioneer head unit during the video is at approximately 50% - I'll get something more impressive up here sometime soon Well now that we've been up and running solid for a few months, I know there's others out there with these bad boys. So.. Where the hell are the pic's?…

I was just wondering how low a pair of 12" rli's will go? In the right box how good is thier low extension? Are they able to play clean in the 20hz range? If do get a pair I'd be feeding each one around 400watts.

HellO all . I need a little help just got my Rl-i 12's A few days ago. still dont know what zmp to get. I got the dual 4 ohm . Im kinda loking at the octane-R 8.0:1 but dont kno the full specs of this amp. dose it run 1 ohm stable and if it does what wattage .Is it 800 rms at 2 ohms or is that just peak power? nsorry new to the whole sounds thing . planing on making one box for each sub about one cbf 2 one & a 1/4 cbf. if I could get some help or sugestions on amps for these sub it wuld be great .

whats the best size for this? i was thinkin like 3 cubes, 30 sq inches of port, 3x10 slot, and tuned around 30-34, i will have anywhere from 6-1000 watts to mess with.

ok folks...i just got my rlp 15 in today...daym, daym, daym she's so good looking...without a logo by the way, the cone, the basket, the rear end, sssso sexy!!! anyways, for now i'm gonna break her in and pop the cherry with my 311d in a sealed box which will give her about 350 rms at 2 ohm mono... i'm gonna be building my ported box over spring break next week...can't wait... just wanted to say she's so sexy!!!

okay, im lookin at gettin 2 RL-i's for my truck (87 mazda b2200) i want it to wang like hell. problem is ive got only enuff for the tens right now. and im tryna build something over time. ive always wanted tens, and saw the site cuz of reccomendations at CA.com. would this be a good setup to fiberglass? or would it be happier in MDF? ill probably stick to sealed, i wont get metered but i want it to hit pretty good. my ears ring on 2 w3's and 500/1 and thats sorta what i base everything off of, being its the only quality system around my area. everything else is audioblown

I am about to pay for my RP-i 12 " sub so it can be shipped. I want to build a ported box and tune it to 25hz. I will be pushing 600wRMS to it. What size box would be best? Also feel free to offer any other suggestions. Thanks

i didn't want to go by myself so i took one of my friend with me...had a little comp he has 2 12" xplod and a LA 600w amp vs. 2 15" RL-p and EGA1400d any way. it went like this... him, on the dash ...135.2@55Hz me on dadh...148.7@50Hz him in the kick panel...138.4@54Hz me in the kick paner...151.1@48Hz him on the headrest...124.5@54Hz me on the headrest...144.3@48Hz http://www.realmofexcursion.com/videos/Sou...ter/rlp15.4.wmv http://www.realmofexcursion.com/videos/Sou...ter/rlp15.3.wmv

Hey guys, new to the forum. The rl-p 12 looks like a good product and i m interested in running one sub sealed. i have a brutus 1500d, can run it at (1500@1ohm, 1000@2ohms). Any reccomendations on box sizes and what ohm i should run my amp at?

alright, i ordered my rlp 15, dvc 4 ohm...def looking forward to it...its going to powered by a MTX 801D...800 rms, in a 5th gen civic coupe...i've build about a dozen boxes before but only done sealed...only lately i've been aquainted with winisd and other port determining programs...so i want to build my first ported box... max outter lenght = 34.5" - pretty much written in stone max outter height = 15.5" - pretty much written in stone max outter width = up to 23 inches on bottom, 19 on top, this is a wedge box... - can be (shorter) smaller, not written in blood max outside cube = 6.49 cubes ********|-----------\ sub is***|*********\ facing***|**********\ this side*…

Hi I am thinking of getting this sub for HT use. I intend to use it with a 350w plate amp, so I require the DVC 2 ohm version. Will the amp power the sub sufficientlly in a ported box? Also, will SS ship to overseas. thanks

im getting a t3000bd would this be to much for 4 rl-p's

I have 550-600 RMS to deliver to one of the two subs lsted in the title (RL-p or RL-i). Will the RL-i be over powered at this? I would prefer to get the RL-i. Let the opinions begin...