US AMPS

was wondering if someone could comfirm that the warrenty on an ax2000 is only 90 day over the counter and 1 year from factory.I read that the xtermentor line has 1 year over the counter and 3 year factory.Just wondering being that i just spent a few dollars on the ax2000 and the 4360 tube.

ok...got all ready to turn on the 600x I just got...did....nothing...then looked at it again....no remote turn on terminal...where does the wire go to turn it on.... the manual online doesnt show anything on the amp connected to the remote wire off the deck...or else I am not getting the obvious...haha.. cant believe I have to ask this...

Why the price increase again this year on the Usamps and RE products? I was looking at bringing in USAMPS Xterminator series but they have gone up.

Whats a good street price for a like new AX2000 and tu4360 tube amp they might be 2 months old.Never abused.

how does a Fi BL 12" fully loaded with a Md1d amp sound? sounds nice to me... but do you think i can go bigger?! md2d?! or probably too much power? any suggestions?

I got my 2 US AMPS in today...thought I might get a 3rd for sub duty although I can get by with the 2 amps I have...wondered if a USA50 would be enough to power a sub...a 10 inch...

Since there isnt a distributor in Canada anymore I'm wondering if there are going to be any dealers in Canada. Maybe US Amps/RE is looking for someone to take over for their Canadian distributions Might be better if they were to answer emails. Does anyone know anything about any of this?

Hi there, just wondering if anyone has info and/or specs on a b100. I have seen it described as a "powered crossover" was this to sneak it into competitions? Any info is appreciated. Thanks in advance.

ok guys here is the deal i have 4 us amps i am going to be installing in my jeep and i need to know what size fuse to put on them i have (1) 4300X (1) 4260 (2) PT-800 what i would like is the fuse ratings for all of them and a suggestion of what size fuse i should use on my power wire to all 4 amps. i am pretty sure the fuse rating on the 4300X is 60Amps I plan on just adding all the fuse ratings up and getting a fuse about that size. thanks -=ScottY=-

How good is the build quality on the xterminator series of amps? Thanks

I have been looking around for information on this sub, but come up with nothing. Not specifications on it, but whether or not I can run this in a daily setup. I know there are a few people who do run these daily, but those are the larger sizes, 12"s, 15"s, 18"s. I have never heard of anyone running a 10. Would it be fine for daily use, or is it similar to the old BTL 10" to where it was solely for burping purposes? Any help would be great appreciated

I had a AX5600 in my car being ran active off a 9835, powering ID OEM mids, Hybrid L1 tweeters and 1 12" RL-p. I've pulled that system out to use the 9835 and amp in my dad's F150, but I'm probably going to stick with some passive TypeX comps in there and 2 E8s under the seat. My question is, are the AX5600 speaker channels bridgable? I'm going to run some old Type-R coaxs off the HU for the rear, but want to send the comps more power than just the front channels. Thoughts? Next, I'm picking up an XT800.2 and two XT800.4s for my car. I'll be running the same L1s, but pairing them with new 2ohm versions of the OEMs. The RL-p is going to be ran IB. I plan to bridge one of t…

I am thinking about getting one or two of them. What is the lowest imp. they can be run at for both daily and burps. Also are they strapable? Some one told me they are .5 ohm stable for daily, and i was wondering what kind of power i could expect at that load. Thanks in advance Rob

OK heres the deal I have the SAT software but now I need to find the Black box interface that goes from the amp to the old 232 Serial port. Does anyone have one of these SAT Interface boxes that can tell me whats in the box and what I would have to do to make one or have one they might want to get ride off?

I'm getting sort of a loud bass note when the amplifier turns on and I was wondering what could be the problem. It was a drop in install since I had an amp installed before this already and there was no loud turn ons with the other amplifier. Also, since I put the MD2 in, I'm getting a lot of noise through my speakers at low volumes. The noises go along with how my engine works (i speed up, noise pitch gets higher). The grounds are the same as I had before and I never had this problem, so does anyone know how to fix this or the loud turn on?

I've got an older USA-2000x which is the 2 ohm stable model. Say if I ran this at 2 ohms bridged, would I be good with a 200 amp alt, Kinetic HC2400 and HC800? Thanks

I just checked the specs on this amp and it is not very high only 200 if I am correct.The JL amp is something like 400 on damping factor.Can somebody correct me if I am wrong.The higer the better if I am right.

So just how much are the ax-600 underrated? The site has them at 190rms/channel but they are underated from what i understand. So the 2006 stuff what will be different between the old and new. OH come give a dog a bone. I think this what i'll be running my cdt ES-7.1 braxials off of. Good idea or not?

i was told straight from mr kim himself to take them down temporarily. all discussion will be continued at a later time topic was not deleted, it was hidden.

i got a buddy who has 3 vlx400 neding repair.i thought i read a post about some of u some of u guys saying only use the old school guys that handbuild the old school us amps? can any of u guys help him out?by giving me some info on him getting these fixed?thanks for the help

alright so the amp i originaly wanted has been discontinued, i found it but i think i will go with a good company instead. i am now torn between US, and Sundown. it basically comes down to the price and where i can find it. since this is the US Amp section i thought i would ask you guys. whats the price on the US MD-2D? and what are some internet dealers?

I've never seen this one before. not mine by the way just thought it was saaweet http://www.caraudio.com/forum/showthread.p...070#post4214070

do they sell shirts if so were???

the screws on my amp are all rusted, some of them are warn down. i've been looking around for some philslot screws the ones with the square to grab on to the wire, but i've only found some overpriced ebay ones. anyone know an online store that has them cheap?

Well i dont know how but i found flakko and then i found this site and here I am. I've never owned a us amps but have dreamed of it back in the days of highschool and college...LOL! I currently have kicker sx line of amps but am trying to unload them right now. So anyways just thought i'd chime in and say hello.