US AMPS

Does anybody how much power this amp will put out with a healthy 14.4V at 1ohm??

Is there any way I can get schematics for an old USA 2000X, USA1000 and USA-150? they all need repairs and being the other side of the pond in blighty I'd rather repair them myself. The USA 150 has smoked some FETs and PSU diodes. The USA 1000 cuts out intermittantly (could just be a dry joint) both those have been abused a bit in the past (not by me, I'm trying to bring them back to their former glory and give them a good home) The USA 2000X was reverse polaritied by a moron (along with the rest of my car when he tried to jump start it) and now has PSU/system noise appearing on the audio, probably jsut a diode gone somewhere but schematic would make it somewhat easier t…

can someone(flakko) get a pic of the crossover section along with the specs for frequency and slopes? thanks in advance

I have an i/s 4065 and am debating whether or not to run this for my Z6 comps. It would have to be bridged and that would be at 3ohms...is this possible for the 4ohm stable amp or a definite no-go? Thanks

i just bought some new subs and im looking for something thats about 2000rms or alitte above and someone told me that 2000x would work really good but i thought i heard those were hard to find.Any info on this??

Hi guys, last weekend I picked up 2 of the US Amps AX1000 (for now), and I'm using them to run (3) 2 ohm Cadence Wild Beast subs (for now). How do you strap the amps together without using the magic "MLT" box? Under the plexiglass, I can see the "master/slave" switches for both channels, but I'm a little leary doing anything to the circuit board without some instruction. Down the road, I'm planning on adding at least 2 more AX1000's and one more sub, but this current set up will get me thru the week. Thanks, in advance

some quick thoughts.... 1) this is a great looking amp! the problem would be how to install it, lol. i mean, rightside up and you can't see the internals. upside down and you can't see the nicely done case/heatsink. talk about a dilemma. 2)the set screws are entirely way too close to the case. it would be nice to see them just a bit further away, not much, but you can already see rubmarks on the case from previous installs. 3) a subsonic filter on a stereo amplifier? nice touch! it would be even sweeter if it was adjustable instead of just on or off. 4) the bridging is reversed. instead of L+ and R-, it's R+ and L-, which meant i had it hooked up wrong and had to refer t…

i could get an older usa-5600x for a good price, should i get htat, or save up for an ax5600?

Just wondering what the current draw is at 4ohm.

I have a question i bought this amp not 3 weeks ago and the rear channels have already stopped working i can tap the top of the amp and they come on but will not come on alone??????Is this something i am going to have to worry about??Should i go with another amp??I had my other amps for 3 years with no problems and the guy that bought them from me is still using them?????

what i've read on a local forum : USamps bought RE audio ...so i have to ask : is it true ? try not to gather the torches to burn me, because i didn't believe, so i had to ask here..

Isnt gonna be strappable???????????? What the hell. Any other news about them. Are they gonna make more power? Are they gonna run lower ohms?

Where would be the best place to get these? About how much will each of these run me? Does the MD.41 do 50W x 4 or 60W x4? Thanks!

hehe this site needs more exposure... after slaving by his computer for hours maybe days, Ravo has released a working database www.12vdb.com www.12voltdb.com add equipment you own or feel that you have a deep connection to, write reviews, etc etc!! 12vdb is now open!! thanks to all who have helped (especially Ravo and Megahurtz)

Hey guys... I have the U.S.Amps 4360 tube amp, and have had nothing but problems with it. The channels keep distorting, and cutting out. This may be because of my custom mount, not just the amp. I have it mounted next to 2 Memphis LVS 15's and mounted sideways I would like to try something else, maybe the 4300X. What would you recommend I try? If I went for something like the IS line would that be moving WAY down? or would something like the 4300X suit me better? I have never had another amp other than the 4360, so the tube is ll I have heard. Flakko can you contact me in some way for prices? thanks~!

http://www.ikesound.com/category-category_id/858 I thought they couldnt sell ax line on the internet. is this a scam or am i missing something i noticed that they had re subs also. Very expensive too.

I have a couple quick questions: 1.) What is the difference between the 05 AX2000 and the 06 AX2000? 2.) Will the AX2000 run at 2 ohms mono? thanks

Was just wondering for a future reference if someone around here asked me...

was wondering if someone could comfirm that the warrenty on an ax2000 is only 90 day over the counter and 1 year from factory.I read that the xtermentor line has 1 year over the counter and 3 year factory.Just wondering being that i just spent a few dollars on the ax2000 and the 4360 tube.

I read in another forum that it should be out in JUNE.Do you Know any details? Any specs? Dimensions?

Hello All, I recently acquired a blown XXX 18" and am going to get it re-coned. I have not talked to their tech yet, but I believe I can do either 1 ohm or 2 ohm DVC. I am running a MD2 (thanks Flakko, I love it) and was wondering what configuration you would choose, .5 ohms or 1 ohm? Thanks for the input. -Rich

Hi I am very happy with all my Chrome US Amps USA series. However I am changing my system, and now need a better Midbass amp. I am looking at the Us Amps Merlin MD23 but I do not see anything other then specs written about it anywhere! Has anyone used it, and can give me your thoughts? I need a amp that does 300 Watts @ 4 ohm X2 and has a high pass crossover that can cross at 60-65Hz. The MD23 fits that perfectly. Thanks.

I have a USA-200 pushing a 12" RLP on a single channel at 2 ohms at the moment. From my understanding the 200 is bridgeable at 2 ohms. This is one of the first usamps I have owned, and I am unsure of which terminals to use for bridgeing. Anyone know if it is the right + and the left - or vice versa, or if I am completely wrong and the amp is not bridgeable @ 2 ohms?

Hey, Need your advice on whether this amp is a good match for this sub. Rated power for sub: 350RMS/700Peak Rated power for amp: 200RMS x 2 @ 4 ohms 350RMS x 2 @ 2 ohms 700RMS x 2 @ 4 ohms Bridged Also, does anyone have experience buying US Amps from Ike Sound. thanks in advance.

So what are the thoughts on the exterminator amps so far. Anyone with experience could u please chime in here. Thanks.