Build Logs

i need to start a builtin log but 1st i need to know if this box will work am lookin for loudness/"""SQL""" and alot of good lo bass playin reggae and hiphop i found this site and was playin around with it an this is what i came up with (sub up port back) need to get advice before i start to built thanks box width 34 box hight 15 both box depth 17 wood .75 square port width 3 squaer port lenght 1: 13.5 square port length 2: 8 total port lenght 26.5 tuned at 32 hz and about 3.306 cube RE Enclosure Calculator

Car - 2000 Mustang Amp - Audiopipe AP1500D sub - 10" Mach5 iXL box - .9 cubes net tuned to 34hz I was going to try for a T-line but theres no room to get a bigger size box really into the trunk and the girlfriend wanted a fairly small sized box so yeah. I just cut out the speaker hole. The port still needs to be glued in. more to come.

ookay thanks to mr James bang again for his fabulous cuts, i can now put this box together.... again sorry bout the bad pix... camera fone waiting for card reader. Equipment Sub: RE SR10 Amp: MD22 (you all know what it looks like) Wires: navone 2 ch LOC and some 4 gauge wire kit im picking up tomorrow Box: .76 cubes sealed little bigger than reccomended but should do good. if its too boomy, i can always add mdf slugs and stuff to cut down the enclosure size/ -------------------------------------------- getting ready to build tomorrow 2 boxes actually SCREW THE SCREWS! clamps + glue and caulk FTW. something looks a little funny here.... mr bang left too much off the …

Ok this build is up on most of the forums but I figured I'd put it up over here as well. There are a lot of pictures so I'll try and only put the important ones in here... Here are the first 2 peices... Working around the stupid hump in the back wall. Here is a picture of the back, this is at a slight angle which is causing all sorts of hell with trying to line everything up. Another shot Once again, those are all test pieces. The only "good" pieces I have are in the first 2 pictures. Pretty much the bottom, back, and the small hump. Another close up of the internal driver side. Shot of the drivers side. All those pieces are finished. Internal of the driver…

Here are some final pictures for a build I did for a customer. Box is 8.4 cubes @ 35hz for 2 HDC3 15's. Box is not being covered with anything. customer will do what he pleases. Gonna be fun to ship... Enjoy

Got another box underway being built for an older for escort, 2 Sundown SD2-8 going in a ported box powered by a planet audio 3k. Stay tuned for pics

Vehicle is 1992 volvo 240 wagon The goal of this build was to get loud on the mids and highs and get as loud and low as possible on two 12's!!!!!!!!!First box for this system was really nice but not enough port area so the bl's werent liking it very muddy sounding wasnt happy so i pulled out my old box and trimed it up to fit the vehicle and it was a perfect match up. Moves some air like it should! electrical consist of 275amp Ohio generator Alternator a 17ft run of welding supply 1/0guage all connections crimped with hydraulic crimper thanks to "Sirlancelot" Yellow top optima g34 upfront with one kinetic 2400 in the rear atm have one more to add in just ran out of 1/0gua…

Well, i crashed my BMW in december and yesterday i bought a new car "Honda Civic" 91. Engine is running great and body is good, but i will get it painted as soon as possible. Also need some new wheels, and window tint. There is no stereo in car, no HU, even front speakers. Pictures.

lets get started shall we? no words no bullshit straight pics, any questions just ask hmmmmmmmmmmmmmmmmmmmm

BIG install coming soon!.... This is my first build out....the only experience i have with glass are with the 2 kick pods i have in there now and it was a learning one! They turned out great but i made the mistake of drilling a big hole through the back to port them...oooops! They made $800 dollar comps sound like a gramaphone....so I'm making new ones. Along with, 2 pods on rear of the headliner, 2 amp racks on the rear panels and 2 enclosures above the wheel well. The equipment... Current System: Kenwood KDC-X890 Head unit Phoenix Gold ZX475 Amp Phoenix Gold XO Elite TI6 Comps Made by Morel 12" Fosgate Punch HE2 Dual 4ohm in a HUGE bandbass box Adding: 2 DLS 8'' Coax S…

Do you have a blazer or s10 pick-up? Post your pics! Here are some of mine. Any questions go ahead and ask.

no text just pics.. 1:1 6th, 2 Ct Sounds EXO 15"s... 6.4 net in the rear, 4" aeros, tuned to 47, front chamber is 7ish net, tuned to 54. here we go.. window bracing

After much deliberation, I have finally laid down the plan for my project build. I planned to do a trunk build, but decided I was trying to stuff to much crap in a very limited space. Deciding to put the enclosure inside the passenger area led me to consider a wall build, but this is my daily driver. So, a below the window line, Super Stock class build this will be. Talk about jumping into the deep end. After torturous deliberations, I decided to go for SB2 and stopped flirting with the idea of ETHOS 15's and committed to an EVIL 18 . Yes, the wait is long and is killing me, but I still have much to do before it gets here. This was the first arrival: This is my Mech…

I think its a Chevy... Anyway, Joel has done a fair bit of customizing on this unit and will continue to do so through this winter. As the first pic shows he has removed the door handles, replacing them with an electronic system that ties into his Viper car alarm. He also did some front and back end frame work. This picture does the truck paint job no justice whatsoever - you would have to see it live to appreciate it The next shot shows the interior with the back seat ripped out. He will also be ripping out his single 12" Diamond Audio sub, replacing it with two SPL-15's. The cap will also go, but the nice Audison 1kw amp stays to power the front stage The next s…

Runing the Knukoncept 1/0 tool of mass destruction joe, playing with the subs more goodies.... getting started looking good, side plate last thing. time for electrical upgrades....LoadBoss 230A Old and busted vs. new hotness I gotta fit that in there...? view from below and above finishing up on box #1, final sanding.... almost done... sand up the putty spots. good enough for me.... time to wire them up... getting thirsty. I'll post some more "finished" pics in a bit.

What's up guys so I started construction and completed my box for 2 12's. Gonna be used for dss ethos 12. Port is 4x20 and box net was 5.99. I used 12volt to see how long I need it for 32hz. It said 27.75 but I rounded up to 28. But I wasn't too sure on how to go about it since it's gonna have 2 bends. I researched it and it sounds super confusing, some saying gotta have the correction part at the end. But I found some that said just measure up the middle so that's what I did to achieve 28" Could you guys she'd some info on if it's correct. If not, could you tell me what frequency I'm at. Alright thanks guys

Ok, so I've never put a build log on here so please bear with me if I mess this up. This started as me wanting to get louder and ended up like nothing I could have imagined. Its a 2006 Chevy Silverado EXT cab 71 pickup with the 5.3L. Equipment installed is: 2 Singer 350A Alternators (stock running as master) MLA Module American Bass 1100.1 5 C&D Batts 1 XS Power up front 2 sets Boston Pro 60SE Components (Running as coaxial) Boston 2 channel 6 SSA Zcon 15s (4th order enclosure) Some tire/suspension mods to hide the almost 2000lbs of equipment. First the walkaround now into the build pics: (I didnt take very many) ^^^^Crossovers in place of factory bose a…

I'm going to be posting random pictures of my installation progress here, and keeping notes of what I have\still need. Excuse the brevity! What I have installed currently: Optima yellow top 4awg from the hood to the rear directed 1200/6 amplifier 2x orion p10d4 (old model subs\amp) stock speakers stock hu - using a line out converter What I have but not installed: mbquart pvi216 component set - most likely will be replaced later 1x sae-1200d 1x sax-125.2 What I still need to purchase: some pioneer HU with, steering wheel controls, onstar, dashkit another sae-1200d some good subs (4xsa-10s? not sure yet.) another battery HO alt (200amp+) 0awg wire, big 3 Ok so that's most …

Pretty straight forward. Has completed just posting for a reference. Also this is my first wall build so its far from perfect

Hey guys as promised started the center console build for two Fi Q 10s. Box specs changed quite a bit because of a too tall center console cushion, but it actually worked out better, I can now make it look a little more one off custom. Box Specs: H:14 W:15 L:30 Net Volume: 4 Inch Dimpled Precision Port Tuned at a hair under 28 Hz Box material was 23/32 Auracco Baffle was doubled for 1.5 inches Here are some pics, the box will be braced with some 1 inch dowels and polyfill will get wrapped around the body of the port along with the exterior being stained to match trucks woodgrain and hand rubbed to a mirror finish. Call me crazy but i cannot figure out how to post p…

In one of my intro threads I remarked it was like an old addiction. Seems as of late well for over 13 years I've mended my ways and laid down my desires for my family. What started as just a small system has resurrected the monster. I have a few goals intended for this system they are: 1. Create a clean install which is removable with minimum effort. After all this is our family car. 2. Target db level 145 3. Modular design to accept several boxes and yet remain SANITARY in installation. 4. Kid proof Covers to prevent kids from dropping stuff in ports (one reason the passive radiator is one of the designs) 5. Design for double the electrical draw. On hand purchased …

Here's my system. Not much exciting going on. 2008 Saturn Vue Stock HU Stock door speakers MTX RFL600D 12" Adire Audio Shiva in 1.21 cubic feet sealed The factory speakers sound pretty good, but are little harsh. I do plan on replacing them in the future, but they will hold me over for now. The HU will probably stay. Onto the pics. Like I said, not much, but it will hold me over for a while. The bass knob is way under the dash and is kind of hard/dangerous to adjust while driving (most of my driving is done at 65 mph). I'd like to move it to the center console somewhere so it's right there within arms reach, but I'm not sure exactly how to go about doing it.…

First off, I'm going to tell you now this is going to be a super long build. I work a minimum wage job and have a child to take care of and bills to pay so they come first, Also bare with me this is my first actual build myself. So if I mess up somewhere along the lines, Feel free to give me some ideas and pointers i'm always up for learning new things. So to start this off, The stuff I plan to run. 2 dc audio level 4 15's 2 dc audio 2k's 2 xs power 3400's PPI S2 Components Mechman 270amp Alt The Jeep SKY HIGH FTW

Well i finally got my truck and got my SAZ-1000D in and my 10" SSA icon. Man it sounds good. I have never heard a sub with such accuracy and overall sound quality. It has a lot of output for a little 10 and i am very happy with it. Anyways this set up is temporary until i build a new box and find somewhere to stick the amp. Box is 1.35^3@32hz. Its pretty good for my 3rd box i would say and i designed it myself. Just got to figure out if im gunna carpet it or paint. Edit - Also my first install that i did everything myself and its still not done. On to the pics - The truck - 01' GMC Sierra with 47k miles. So far all i have done is get the windows tinted and the sub in. …