Build Logs

Well, i had subs up, port back in 2 different boxes, then walled and now got design done by robin for 4th order bandpass for 2 bl 18's. Took couple pics when building, will take some pics of all in truck tomorrow. Still got to put other front on, make trim panels and repaint inside of box. But i can do all that while its in the truck. I am using matt and fiberglass on all seams inside, has 1" rods inside, and adding all thread from side to side for extra bracing. Hopefully will be finished by tuesday. Still got lot left to do, but had to put in truck while i had the extra help to move it. So far, just from playing around a little it sounds alot louder, has a total di…

Facebook for Triple R Performance I hate photobucket now, so i am just going to use FB!

the ol' beater pioneer deh-p680mp got it for $50 bucks today i used some jensen 5" pods that were under my dash and a pair of memphis 15-PRC5 Power Reference 5"(free) and i piece of mdf and came up with this also for some highs i found these in the garage and supprisingly the jam pretty good now electrical wise i have 4ga big 3 temporary....cheap new batt, and new stock alt that was free amp i got now is wack but in a week im finally gonna send my saz1500 to db-r.....that voltage is w/ the car off sub is a rockford POWER hx2 15 d2 - box is around 4.5 cuft ported and tuned @ 40 hz volts at idle 1. 2. sub is in backseat.. ill go ahead and say it now b4 u ask 1. i…

I'm not sure if this is the right section I hope it is. I hope you guys enjoy the pics http://i883.photobucket.com/albums/ac40/gadgeteer123/Xcon/100_0381.jpg

Here are pics of "Moms Soccer Van" before it goes in for custom vinyl graphics. Rear windows have been blacked out and urethane sealed To prevent flexing. Passive crossovers flushed into the passenger side under seat drawer. Refer all questions to 02skidoo as I only assisted on the dampening and tweeter install and brainstorming. Brian did all the rest himself. All dampening is Rockford Fosgate Deadskin (1 layer roof and sidewalls) Alt is from Ohio Generator and 3 Kinetik's. Could use a couple more. Now all I need to do is talk the Owner into Sundown and others!

Deezy Dee's Chevy Impala Build Log Inspired and made come true by Hove's suggestions 06 Chevy Impala LT (Slight Modifications, Rims coming soon) One Fi BL 15" Sub woofer (Daily, Coil, ect) 1000W Sundown Audio AMP Shuriken High Performance Battery (80Hrs) 31 Feet of O/1 Gage Wire, RCA's, all accessories ect Stinger Volt Meter Pioneer 6100BT In-Dash Box Built by Argent Audio (Andrew) Double Baffle, Flush Mount, tuned to 33hz - - - - - - - - - - - - - - - - - - - - - - - - - - More pictures after the Install is finished, and my face to hear my new system (first system) Stay Tuned

Been a while but I am finally back at it... the DIY'er in me got the best of me once again. This is the current system: Stock Head Unit Front Stage: JL C5s Front Stage Amplifier: Sundown 100.2 Rear Stage: Stock. Has been about a year and sounds awesome to me, but we can always get better (plus I miss subs). It will be a while before it is all finished but this is what I am planning for the new set up. HU: Alpine W505 Processing: Alpine H701 Active Front Stage: Cd1 Pro Minis for the tweeters and X69s for the midbass Rear Stage: JL C5s Substage: (2) FI Q 15s sealed Amps: (2) 1.000 Alpine PDXs, 4.150 Alpine PDX, 4.100 Alpine PDX. Pics coming up...

Well i havent created a build log in a long time on here. I recently decided to pull out ALL of my high end stereo equipment to make room for my new baby girl thats on the way. I settled for (1) Kicker Comp 12" on a no brand name Amp that i dug out of the trash and fixed................ I cant take it ANYMORE!!!!! I gotta have something that will do a little damaged when i need it to soooooo say tuned. Today i will be attempting to build a new box for one of my SSD 15's tuned somewhere around 28-35 Hz....havent decided yet........but i may need some design help!!!!!!! STAY TUNED. (1) Fi SSD 15" D1 loaded (1) Kicker ZX2500.1 (1)Kinetic KHC1800 Battery under the hood (…

Have been planning this for a lil while now. Being busy with school and what not, it has been a long time coming. I finally started the other day though. Just a heads up: Being in college full time, with a ton of papers coming up soon, this will not be a fast build. Just gonna work on it when I can between class, gf, and other things until its done. What's going in: 4 DP21"s 4 SAZ-3000d's (new heat sinks) Maxx-Link 200+ ft. Tsunami Competition 1/0 (5+ 5- runs back) 9 Deka 9a31's (1 up front, 8 in back) 1 DC Power 270 amp alt (for now) 4th order designed by iamamp3pimp Other misc. things All in an '03 Expedition XLT Big thanks to …

Ok, so for the people who know. I posted a buildlog a LONG time ago with the old T1's in the trailblazer on the AQ2200D. Well The box for those was not optimum for the Havocs, so i designed him a new one and got it all done. Lemme know what yall think. Didnt take many pictures, but heres what i got. Il get more shots and vids sometime and post em on here.

1.39 cubes net tuned to 39hz Double baffle top for flush mount with carpet. I am very impressed with the SDC2.5. It sounded great and got low and loud. I'll try to get the owner to get me some in vehicle pictures as I forgot to when we installed it because we were busy listening to it.

Red paint to cover the outside of the box to match a 05 mustang gt and the port will get another coat of black.

My first build was not posted here since it was before I found this awsome site but I will post a few pics of it. I recieved my Sundown SAE 1200 amp today and awaiting the 2 SSA Icon 12d1 subs. The box will be ported instead of sealed this time with subs firing up, still poundering on port location. Should I go out the side on bottom or up also? The box will be approx. 4.1 cubs tuned to 30hz. Picking up wood tomorrow after work and hopefully start cutting sat mornin. I know its alot of trial and error but if anyone has experience with extra cab trucks and port locations feel free to add. Here is the current set up in my 95 Mazda B3000 Kenwood KDC-X790 head unit JL Audio e…

One reason for the rebuild: Cone Area This rebuild has been in planning for awhile but it's just starting to come together now First off I wanna thank the people who made this possible; Thanks to Jacob at Sundown for having such great equipment, customer service, and for answering all my n00b questions. You are the man! Thanks to Zach (Nightshade) for helping with the box design and answering even more of my n00b questions; you've been so helpful and generous with your time, I owe you man. Thanks to Derrick (Derrick824) for helping me with the initial planning for the box, it was great working with you! Thanks to Torres, for helping me with wiring when I had no idea WTF …

First and foremost big thanks to TMH for designing and building the wall(I helped but he did most) lol Tested at 150.4DB @ 31hz sealed legal on TL. Truck now peaks at 30-31hz. Also did a 151.8 outlaw... Set up; Head unit(s) Alpine 9886 in front -------- Front stage 2 DD 6.5 components in each door Crunch GP 1600.4 amp -------- Rear stage 1 DD 6.5 component set Crunch GP 700.2 amp -------- Sub stage 2 18" AA mayhems D1ohm ~16.5C.F wall tuned to 28-29hz 4 6" Aeroports 2 Hifonics XXV volossus amps 12 Panasonic AS00815-1 28ah batteries in the back DC power 315a alternator 2 runs 3/0 welding cable Now onto the pics.... …

Cut the hole for the speaker. i wanted it as small as possible so it barely cleared the magnet.... i ended up having to make a slot for the wires thou I didn't get any pictures of the speaker ring but it had a roundover instead of being flat and had a kurff cut so it would bend with the dash. Nothing major just a slight bend BUT it made a huge difference in the end result. These pics are in mid sanding thou, the ring was fiberglassed to the dash popped off and i snapped some pics after the first stage of sanding After looking at it on the dash half way ready i realized the orange wasn't going to work... So i painted the speaker while the final sanding and stuff was bei…

I will get straight to it. I have a 2006 Dodge Ram 1500 ST. Inside will be a combination of items. For head unit I am using a Pioneer DEH-P6000ub, For proccessors I am using Audio Control Four.1, Epic-150, and a 24xs Crossover. Amplifiers are Soundstream PCX1500d and Rubicon 2.250. For subs I am Soundstream PW15s subs and door speakers are Eclipse 8062 6.5" Components with Soundstream TSW.3 tweets. For power I am running 2 Shuriken SK-BT60 batts. and a Power Acoustic 10 farad capacitor. For power and ground I am running 2/0 main scaled down to 4ga from the dirsto to the amps. New box dimensions are as follows: External dimensions: 58.5"w x 16"t x 9"d. Internal space is 3…

Im still new to the forum, but I decided I would post a build log of my truck. The Truck: 2006 Schevy Silverado 1500 Extended Cab, 5.3 2wd. As it sits the truck is stock, when things start coming in I will start the install. Hopefully I will start with the deadening and running all the wires. Almost current pic, before clearing the headlights and tinting the windows They components being used: Head Unit: Kenwood DDX 812 Mid Amp: Sundown SAX50.4 Sub Amp: Sundown SAZ1500D Subs: Sundown SA-8 (2) Mids: Hertz HSK165 Deadner: Raamat and Ensolit…

In one of my intro threads I remarked it was like an old addiction. Seems as of late well for over 13 years I've mended my ways and laid down my desires for my family. What started as just a small system has resurrected the monster. I have a few goals intended for this system they are: 1. Create a clean install which is removable with minimum effort. After all this is our family car. 2. Target db level 145 3. Modular design to accept several boxes and yet remain SANITARY in installation. 4. Kid proof Covers to prevent kids from dropping stuff in ports (one reason the passive radiator is one of the designs) 5. Design for double the electrical draw. On hand purchased …

Does anybody got a build log on a caliber...if so post it...might post a picture of my setup but all i got is some piece of shit 12" kicker cvrs in a 4.4 cubic feet box...only upgrade so far still even have the stock piece of shit radio plan to upgrade to a touch screen double-din....and plan to upgrade to an 18" fi bl or btl...

This is about 2-3 weeks pre build. But I finally got pics so there gettin posted. when the build begins ill just add to this thread. here is what ive got my hands on so far... all Knukonceptz wire.. 8gauge,4 gauge and 1/0, rca's, fuses, remote, all connectors 220A Alternator This is the only thing i bought used in the entire build so far. has a small scratch on the front, but powers up and sounds good, price was un beatable so i had to get it one more kinetik and some deadener and this all gets put into the vehicle..i would have a picture of the tahoe but it looks like shit right now, maybe another day

Here is a teaser pic for my new console that's going in my truck. Hopefully the picture will show up since I'm new to posting pics. Looking forward to documenting the process for you guys.

So I don't have a ton of pictures I was putting everything together and was on a roll so I didn't stop to take a lot. I have a couple videos I will post too. So enough of me talking....On with the pictures. When I received my Sub Enclosure. OLD VS NEW Now on to the sub. Wire from KnuKonceptz. 6 Feet of Red 8 Feet of Black 10 Feet of Karma Speaker. Need to take some pictures of the trunk still and what not but next post will be videos.

I've been here long enough. Time to nut up or shut up, as the saying goes. Here are some pics of what I built. The goal: Loud. How loud? 140+ on the Term lab. The challenge: To do it with low power and a sTock electrical system. Journey with me as I go for the moon. First some info of my build. The car: 1994 Oldsmobile Cutlass Cierra A.K.A The Cream Puff Head Unit: JVC KD-HDW10 A basic CD player with a built in HD tuner and RCA outputs Amps: 2 US Acoustics USB-4085 1 at 85 watts x 4 @ 4ohms (mids and highs) 1 at 240 watts x 2 @ 4 ohms (subs) Fronts: Powerbass 3.5" coax in stock location Rear: MTX Thunder Axe 5-1/4" components Subs: 2 Ascendant Audio Atlas 15" Electical: S…

not really a build log but here is the box i made 0.90 @ 35hz with 400 watts in the pimp wagon trying to do hair trick the box had some leaks so im fixing those now