Build Logs

Have my son for the day while the wife is out, so I figured I'd post some pics:

My latest project. It's actually a very big one, but it's extremely unusual. Alot of these posts are cross posted from my 'other' sound forum, but they should make sense My new install comprises of the following.. Sony HU (high end one, tho I dont like it very much) NESA DVD player, 10" overhead screen Fusion FX 45 multi function unit, parametric EQ, 8v line driver and active XO. Phoenix Gold MPS2220 to run entire stage Phoenix Gold ZX200 bridged into 2ohm mono into sub. Front stage. pair of 3.5" 2 way Clif designs. Pair of 6.5" 2 way clif designs. Pair of alpine tweeters. Rear stage. Fujitsu Ten Eclipse 6x9 point reference series component mid/tweets. Subwoofer. JBL G…

i promise, this is the final plan. i was talking with Little Jon (white van, 16 12" ssd's) and hes like just wall it, and that gave me some ideas, so i just got home, measured in the back, and this is what i came up with. of course im not sure on the port yet, or what subs, deff not gonna be like the truck though. its going to be built outside the car, and slide right in and bolt to the floor. it will be completely removeable, and the seats will be able to be put right back in, if i ever decide to take the wall out. all the side trim, etc is staying in, and nothing is getting screwd thru it, or cut, or anything like that to mess it up. it will be right up to the front sea…

This is my second build for the BTL 15 i have. IT is wired at 1.2 ohms power by my Mean Machine 3000.1, with an NSB90 in the trunk hooked directly to the alternator. Hope you enjoy. box is 3.5 cu ft tuned to 35 hz

Pics were upside down, new links with correct pics edited!

so just came in the mail.... 2 15's soon to come is a saz1500d. so here are some pictures or random chit as it happens i guess.... thats all i got.

selling the Pro60's (someone buy them, check my FS thread) putting in B&C 6PEV13 mids (front doors) and Selenium 6W4P 6.5s in the rear. i still am looking for 4 tweets to go with these 4 mids. amps will be a RF Punch P550.2(mids) and a P200.2(tweets) it will be active, but not a "true" active setup if you wanna call it that...i will be using FMOD "crossovers" from partsexpress...2500hz high pass for tweets, 2500hz low pass for the mids: http://www.partsexpress.com/pe/showdetl.cf...tnumber=266-288 heres a better layout of it, minus whatever tweets i choose: heres pics of the MDF "rings" i made today LOL....had to make them like this becuase the lower corner barely cle…

Got around to building the box today for my BL15. Anywho on with the good stuff... Overall I'm really impressed with this thing. I like it alot. I will carpet it later I just wanted to get it in and start breaking it in. It wangs . --edit-- The 6" Aero is in the box as well. It's not sealed

Going to start on my semi-SQ build today. Can't really call it a true SQ build as of now because of a few things that I'm sure will be pointed out by the SQ guys on here. Headunit: Pioneer deh-7800mp EQ: Rockford Fosgate Symmetry Amp: Sundown SAX-100.4 Mids and Highs: 2 sets of CDT EF-61CF's CDT Imaging mid-tweeters in the A pillars Subs: Sundown SD-1 12's Enclosure: Chambered Transmission line tuned to provide a nearly flat curve from 20-65hz. Gonna get started on the build this evening, and on Tuesday my Termlab should be here, and I'll get some base numbers, even though, as you can tell, this isn't going to be a ground shaker. My RTA should be here soon, and th…

my new install will be up this weekend. I've been debating on how to upgrade my monoblock power and my electical system and i came to some costly decisions but I think I'll be happy with them. I will still be using my BTL 15 dual 0.7 fully loaded but in a different enclosure. which is currently complete but I'm waiting to put pics up till saturday because my new toys all come in this week via fedex. New setup::: 15 btl fully loaded wired at 0.5 ohm ( due to impedance rise ) 3.5 cuft enclosure tuned to 35 hz. Mint Autotek Mean Machine 3000.1 wired @ .5 ohm brand new NSB 90 battery in the trunk.

Well, its vacation time for me again. That can only mean one thing. I've had most of the equipment for some time now so there is nothing too new. My CDA-9835, freshly repaired and ready to rock. RE 6.5 components, need to redo some aspects of these kicks. View straight back from the passenger kick through the trunk, all passenger seats removed, the only one going back in will be the front passenger. My fully loaded 18'' BTL. Refurbished KX100.2 without its end caps on. New wiring, all Knukonceptz. Still awaiting my excessive amperage alternator, figured I've got most everything I need to get jumping on this.

Well here is what I have installed in my 07 ram quad cab. 1. panasonic 8805 HU 2. phoenix gold tantrum 400.4 (door speakers) 3. blaupunkt 6.5" components (front doors) 4. blaupunkt 6.5" coax (rear doors) 5. phoenix glod tantrum 1200.1 (sub) 6. TC 3000 15" dvc-2 What do you think?

Well figured I had better make a build log for this. I have 40ft^2 of Second Skin Damplifier coming tomorrow and I'm buying another 40ft^2 and 18ft^2 of SS Luxury Liner. I also got my comps in the day before. Rainbow Profi line 5.25" set. I went with the 5.25's b/c I want to keep the truck looking as stock as possible. I'm still debating on were to put my tweeters and the crossovers though. I'm open to any suggestions... I'll have lots of pictures through out the whole process. It will probably take me a good week plus to do it all b/c its my only vehicle and I need it for work so I will have to work small area's at a time. I'm hoping to deaden the crap out of the…

Box build is happening today, it is raining right now, waiting for it to let off to get the first layer of resin in the box... Four more cuts today, and than its just assembly and glass work. I am probably gonna order 80 sq feet of second skin soon and throw some of that in. I have already removed all of my factory speakers. All of the equipment for this build is in my signature. Will be updating throughout the day. Box is 3.68 cubic feet (before port displacement) with 69 sq inches of port. Double front baffle, countersunk screws, and completely resin'ed. Will be holding two 10" TC sounds oem's and tuned to 42 hz. So here are some pics:

So this is what i've been up to for the past week, 2 gallons of spectrum firewall on the inside of the fiero, i figure i'll buy another gallon and a roll of raammat just for the roof/doors. The quarter windows were broken so i made some of those too, the driver's side is still hardening and i haven't even trimmed out the other yet, but they look god so far. considering replacements are $200+ i'd rather try using my leftover fiberglass first.

This is my build including a BTL 15 d 0.7 fully loaded in my 01 Grand Am. Powered by my SoundStream PCA 2000d. The sub actually reads 1.2 ohm so thats pretty cool. Internal lengths heigth = 16 depth = 17.5 width = 30 4.86 cu ft total PORT LENGTHS height 16 width 5 depth 18 displacement of port is .78 cu ft port go down 12.5 , then go right 5.5 tuned @ 45 hz with alot of HELP from ZEUSILICIOUS ON ca.com Thanks Man ya the last photo had the light on it because it was actually DARK out...i was workin on it all day... Hope ill do good at the comp on sunday July 29th!!!

I Work at Audio Adrenaline 2517 Great Western Suite P Prescott Valley,Az (928)772-7785 Here are some of the projects we have had or are working on.. I will keep you all posted on my new projects..

I'll be updating this thread as I finish. I hope to be done by this weekend if not before then Out with the old: JL 10w3v2 in a sealed ProBox powered by a JL 250/1 In with the new: 12" ICON D2 in a ported box built by mrray13 and powered by a Sundown Audio SAE-1000D Here's some pics of my truck: I'll keep updating as I work. Right now the gorilla glue is drying on the MDF that I'll mount the amps with on the back wall -John

I picked up the Sundowns and the Eclipse 8443 back in December and threw in a temporary set up. Now that I'm not having my life sucked away by a manipulative bitch, I'm finally getting the install completed. I'm rebuilding the RL-i boxes to be slightly larger and not have airleaks and be more attractive. Side panels will be build into which the amps will be flush mounted. Hopefully, I'll also get a chance to build a cover panel for my rear deck this week. On to teh pics! Eclipse 8443: Some boxes: Sundown Audio SAZ-1500D: Sundown Audio SAX-100.4: Temp. Install: New boxes for the 8s coming together: That's all I have done so far. More to be posted as I complet…

starting a new build in my bravada.. current set up- 2 MTX 9500 d4 12"s 9 cubes total, tuned to 32hz 1 yellow top RF 100 amp circuit breaker 1 run of 0/1 RF RCAs Jensen 7inch flip out hifonics xx-zues stock alt... stock bose interiors new setup 300 amp alt 4 runs of 1/0 hifonics xx-cyclops 300 amp fuses 4 kinetik hc 800s or 600s (see what i can fit after the box is built) 2 loaded Fi BTL 18s 16 cube box tuned to 33hz eclipse EA4100 4channel for highs eclipse EA2000 2channel for mids midrange & high range drives TBA wire new amp in on the MTX's.. thats all for a few days one question to everyone.. can bass cancel out it sef if the driver i…

Me and my brother have been working on a little project, thought you guys might like it... First off, the equipment. Four FI 15 inch BL subs, fully loaded. Powered by four Ma Audio HK802SX amps Fi BL on the left, MTX RFL in the middle and his MA 12s from last season This is where it all goes Little sound deadner, Dynamat and elemental mental design stuff Rebuilt the door panels to look a little better and hold two 6 1/2 distinct audios My favorite thing...custom ANL fuse holder Got a little more done today but didn't take any pics yet. I will keep ya all updated the best I can and we are open to any suggestions. Lee

a pair of these a pair of these (Atomic APX12s) powered by 2 Atomic AT 5000.1(lol forgot to take a picture of them) in one of these switching the Focus to a diffrent class and running the Crx in street b

procrastination is my worst enemy....jeez. anyways i started glassing my left door some time ago and just started up again. back then.... all taped up: ready to go!: first few layers: and it stayed like that for a couple months.... today: some guides so i can raise the back for more airspace (no releasing agent) : they fell off while cutting it. oh well ill glass them back on: and i finish the nite by closing the back area: more to come...

well me and one of my friends decided to start up a build on a wall for 3 15" BTLs... come to find out only 2 will fit but its all goot 2 BTLs it is front stage is yet to be figured out along with the sub amp.. 2 runs of 1/0 for power 1 run of 1/0 for ground phase linear touch screen ps2 8" lcd in airbag lots of fiberglass work bla bla bla heres the pics the car.. 3% tint all around, 3 rear windows are spraypainted black inside no longer transparent stripping the car