Amplifiers / Head Units / Processors / Electrical

Ok I hope I set this up correctly. Got another question for everyone. Decided to make it a poll. Years ago in the area I grew up in everyone used bass blockers to remove lower frequencies from the smaller speakers 4x6, 5x7, 6.5 and 6x9's. Keeping all the lower bass to the larger speakers. The smaller the speaker the higher the bass blocker frequency. The larger the speaker the lower the blocker frequency. Till you got to the subs. Then they were controlled by the amp so none were used. I have never used them myself. But I am now finding myself looking into purchacing some for my non amped, non component speakers ( the ones listed in the poll ). What are your op…

so, im borrowing her mustang for a week, and shes using mine but shes got a few problems i wanna check to make sure before i do anything. 1. after about 2 hours, it all cuts off... im thinking cuz her amp gets too hot. its a dual 600w amp i think, and its powering the inside speakers, and her 10" xplod. should i rewire the inside speakers to her head unit? only bad thing is its a 4 channel amp i think. so, how would i get that working with just 1 10" sub? or should i leave that alone? 2. hermusic lately has just been cutting off for now reason. i THINK the fuse on the power wire from the amp is loose cuz when you wiggle it around the fuse, it works again. mabe i should r…

i was just wondering if anyone has had any experience with the AQ1200D, its cheap and i'm debating if i should save my money and get it.

okay so i have done a search on this all over, and i did find one post about someone who only used the front channels and then connects the rear channels directly, but kept the fader set to the front, but this just sounds like a bad idea what i want to do is amp my front speakers (alpine type r components), but leave my rear speakers on the head unit's power (alpine sps-400's) i just bought a rockford fosgate t400-2 off a friend on the cheap so i was planning to use that (type r's with only 17 watts have absolutely zero bass) head unit is sony-gt240 ( i know sony isn't that great, but the sound quality is just as good to me as it is on some friends alpines and pioneer h…

I have a 400 watt class A/B amp running 2 10's right now. When I'm listening to rap music, after an hour or so, the amp shuts down from overheating, even if I don't have the volume up too high. Should I switch to a class D amp or would it not be worth it? I listen mostley to rap, but listen to rock and country too, I like to have acceptable SQ.

Hey guy's. Just doing some research and was wondering if the deka was comparable in power to the xs? I can get the deka for 225 and the xs for 290. The price difference is great but is the quality and power there aswell? Thanks Matt Cusack

I was going to write a giant post, but figured this will be better Vehicle - 2006 Ford F-150 XL What I plan on doing: Fi BTL 18" power by Lanzar Opti6000D 8 Pioneer 4-way 280W Max 6x8s on 50Ws each Supporting upgrades: HO Alternator, something with a high idle output Isolator splitting between stock battery for car and 3 batteries in bed of truck Big 3 with 0 Gauge 0 gauge from alt to all batteries Fuses throughout system Voltage meter in dash If you assume I know how to correctly make a ported box, and how to wire stuff, is there anything I am missing or should do in order to make the system more stable? I plan on using 0 gauge for grounds, but feel like I should ask her…

Hi guys, had this question in my head for a few days now so I thought I would just ask. I was wondering what the difference is(if any) between a standard bass knob or a bass processor such as an epicenter from Audio control. More specifically, a potentiometer vs. a parametric eq. How do they work? Do they increase voltage? What exactly is going on when you crank on that knob? Thanks

I have a DD 9512 (dual 2 ohm) and two Autotek MM1400.1D's. I wanted to run each amp on each coil at first, but I was told this is actually pretty risky and it is a lot safer to strap the amps together.. The only dilemma is that once strapped.. the amps will only be stable at 2 ohms.. but dual 2 ohm drivers can only be wired to 1 ohm or 4 ohm.. if i can keep the voltage between 13.5 and 14 volts at the amps, will it be safe to put a 1 ohm load on the set of strapped amps?

I want a new Head Unit and i've seen this idea done before on SMD.. i didn't stick around to see it through though. I'm concerned about the fact my system might not be capable of being powered by an iPad. I'd have my dash fiberglassed for a nice fit. What would the PROS and CONS be? The system would consist of (2) Sub Amps ( around 8k ) and (1) Front Stage Amp. ( 4x100 ) Would it be possible to hook up? If so, HOW?! Also.. heres some other questions i have. How would I keep it charged? The EQ.. whats your guys thoughts about how i would set it up? -- Would it be the same as a regular Head Unit? Would it be possible for my equipment to fry the inside of the iPad? -- to m…

US AMPS MERLIN MD1D AMPLIFIER 1200 WATTS RMS AMP - eBay (item 200477055940 end time Jun-26-10 12:02:09 PDT) I have two RE REX subs and want to run them temp on it and i think this is a pretty good deal. If i do push the RE's with this amp i will have to set the gain order not to pop them only reason i ant is because I might keep it for future upgrades Tell me what you think.

Ok guys I thought my sae-1200 v.2 was screwed when I wasn't getting any output from it at all and it was randomly going into protect mode. I decided to check my connections and behold they were really loose, including the speaker wire on the verge of falling out of the terminal on the back of my box. I redid both of my speaker terminals inside the box and now my amp is not going into protect mode whatsoever. But when I turn the volume up to a decent level it just cuts out but it isn't going into protect mode. When i turn the volume down it comes back on. So I'm almost positive it's low voltage. I'm going to be completing the big three and putting an optima yellow top up f…

Has anybody seen this Hu, it's bad ass! And if so does anybody know if this will be available in the US. Thanks

I have just got a btl 18 fully loaded and am now looking for a amp and was wondering witch would be better one? I will be running all Knukonceptz 1/0 awg fleks wire with a big 3 upgrade with a new xs batt onder the hood so what amp would be the best thank you very much !

just looking for feedback on these can get for cheap

hi, i had to change my plans and have to go with a more budget friendly set up around 300 for the front stage amp . ok right now i have a sundown sax100.4D that i love. but the problem is it is too long i need 3 inches of it to be cut off for it to be true love. so i am i going to have to sell it. and i was looking at small class d amps. and i saw the kenwood xr 4s. for roughly 300 it is rated for 120 rms at 4 ohms and can do active. and on diyma it seems to have gotten good reviews and i do like the fact that it has a fan.. but i never have ran kenwood before . and the only other options i can see for me is getting 2 2 channels amps and stacking them since i want atlea…

ok so i figured id give em a try and ordered a h/o alt from db electrical. suppose to be 200a at 1200 rpm n 105a at idle, but wats idle to them? im running a sundown sae 1200 v2 at 1 ohm so around 1500w rms. when im driving down the road the most ive seen voltage drop is about .5 volts on very low hard hitting songs. that part is wat i do like. wat i dont like is when i pull up to a stoplight or stop sign voltage sits at 13.1 with nothing on, 12.6-9 with my lights on. if im in park at idle voltage will sit around 13.9 but if i do anything, roll down a window, turn on the air or heat it drops dramatically, windows pull it down to low 13s(thats one window at a time, rolling…

I am going to be using my crossfire vr4000d. 4K @ 2ohms. I believe my 2009 caliber srt4 has a 140A stock alt. No H.O. alts are made for this car yet I don't think. What kind of electrical would you guys do for 4K?

I've got a pair of db drive plw12d4 currently on an alphasonic pma600hca and i was wondering what might be a good amp to run so i can put a little more power to them when I build an enclosure better suited for them. How many watts can they actually handle?

i was just wondering if anyone knows how much a Memphis 16-MC1.1500 would cost?

i was just wondering how much the EXILE XI1500.1 cost?

Would I be able to run 2 alternators on my 2003 Lancer if i made the bracket and had room for it? If so how would I go about wring the second one in, or could I have it wired to just my audio battery ?

Has anyone had any experience with Shruiken AGM batteries? Can they be used as main battery replacement? Or are they just for auxiliary use only for audio?

Is there any difference between kinetic racing batteries and regular kinectic batteries? I'm looking for a trunk battery for my build and was looking at an HC2000, but I found a better price on the KR2712. Which looks to be the same battery but in a red case. I went to kinectic's site to look up the racing line of batteries. But they aren't listed anymore. Which I'm guessing is why the racing line is cheaper since it looks to be discontinued.

is there such technology? i had an idea hmmm... wouldnt it be great to watch digital broadcasted tv in the truck. so what im basically asking, is there a headunit out there that can pickup digital tv broadcast? give me a link & or reason why they dont exist