Amplifiers / Head Units / Processors / Electrical

I have a Hifonics Brutus 1200 watt mono and a 15" FI BL sub. Any advise on how to get the loudest but still the best quality out of it? it's Level 9v - 0.2v , Phase 0 - 180 , Bass EQ (keeping it down) , Sub Sonic 15 - 35 Hz , Low Pass 35 - 250 Hz.

I was wondering if my Hifonics Brutus BXi 1610D amp can handle 18v? and if so how will it affect its sound and output? I have a 58amp continuous output switching power supply that I just bought to power it in the house, of course i'm not expecting full power, but I was just wondering how well it will handle that voltage and if it is to high the power supply is adjustable. But let me know ok, hopefully it will be better than my 12 volt 16 amp power supply that it is on right now.

Does anyone have any reviews or info? Im thinking of trading my JL 1000/1 for a 1400d.

just ordered 3 sundown audio sa8 dual 2 ohm -400watts rms ---i no there are a few ways i can wire them up one way does 1.33 ohms and other is 3 i think cant remember got to double check that one -----ill be in a sealed box. -----need an amp that will push them it will be a daily driver so something where they can run for a good hour with out damaging anything

at the moment i have a hifonics brutus bxi-1210D. I recently saw on the ssa store front page the saz-1000D and also heard the sundown amps are rated at 12v which is awesome for me because I still have not upgraded my electrical, i will be just havent yet. My question is, will it be worth it to sell my amp for another that does around the same power? Isnt the sundown just a better all around amp? I just think its a little flashy and funny lookin haha.. Good amp dont get me wrong but I want an amp with 0gauge inputs kinda. I am running one fully loaded bl 15" and i think the saz would just be a better match.. does anyone know if the saz1000D has a bass knob? you know like t…

I just recently purchased a Sundown SAZ 1500d amp and I was lookin thru the manual and I noticed something in it that if I'm running 1 sub that I should run the -wire to the positive and the +wire from the sub to the negative terminal on the amp for the speakers. Is this a error or this is the way I'm supposed to do it ?

I sold my old HU to a buddy the other day, so I went to wal mart for a quick fix and bought a 100$ JVC something-or-other to replace it. I wired the ground, the 12v, and the ignition, and nothing happens when I turn the key. I didn't wire any of the speakers, for I am just running RCA's to an external amp to power my mids and highs. I've checked all fuses, including the one in the HU itself, and re-wired everything just to be sure. After that didn't work, I took it back to wal-mart to replace it, and when I wired the new one up, still nothing, so I know it's not a problem with the HU itself.. Any ideas on what could be the problem?

Ok here is the deal, I have a 08zx750.1 mono kicker amp & unfortunately I sent it out to kicker because I was having problems with my amp cutting off and on, when I turned up my music @ high volume. so kicker repair center diagnosed it and told me that the pcb board was cracked so he gave me a deal of 2010 ZX 750.1 Brand New with 2 year manufacturer warranty for the price of $209.00 or to return my original amp back to me. I was wanting your in-put whether I should get that deal for that brand new 2010 Amp for $209.00 or should I just invest my money on another amp? The set up I have is a 12' inch L7 Kicker dvc 4ohm & I will not be upgrading to add more subwoofers…

I've been going back and forth between buying amps and i cant decide which one i should go for. I'm looking at either getting a refurbished Rockford t30001bd or a refurbished Autotek mean machine 4000.1D. I cant choose between the two and i need to decide soon can anyone help me choose which one to buy.

anybody know what the power rating is for the zed audio kronos is at 1ohm?

my alternator has 110 amps and i have a sundown saz2000d and getting the xcon...yah.. gonna get a beefier bat in the front and a decent size in the rear. how many amps u guys putting out on your alternator and how many watts u pushin out of your amplifier?

i no longer have the tools that go on the sides of the reciver to pull it out any suggestions on how to otherwise do it ... like the little strips of mettal that are used to pull out your reciever out i dont have em any suggestions

http://www.ksl.com/index.php?nid=218&ad=10168316&cat=20&lpid=] Crazyness!!!!

Hey hi i have the MTX 2300x amp , i am about to put it in my car for a sub, but i can;t remember which two speaker outputs to use the markings are all worn off could you let me know thanks for any help

I have a 2006 Dodge Ram 1500 with the 4.7L engine. I am going to be installing a rather large system, and I am having no luck finding a go replacement alt. I will do either a new replacement or if i can find a shop in the Houston area i dont mind upgrading my current alternator. Any help would be great

Hey guys, I'm pretty new to the forum, I've been lurking for awhile trying to learn as much as I can. Anyways, I've had a 15" Memphis sub and a Memphis Power Reference P200.2 two channel amp for awhile. Lately my sub started to sound like it was fixing to go. I found someone selling two Memphis 12s in a box on Craigslist. I went and met the guy and hooked up the speakers, and they sounded good, so I paid the guy and started to get on my way. The speaker wires this guy had for the 12s were crimped and part of the metal was exposed. I went to push the box the rest of the way into my Explorer, and like an idiot, I let the exposed metal on the speaker wires make contact. Smok…

JUST PURCHASED A NEW 1200D.HAD IT INSTALLED,PLAYED WELL FOR 3 DAYS.AND THE OTHER DAY,I GOT IN MY CAR,STARTED UP,TURNED MY HU ON,THE BLUE LIGHT LIT UP AND TURNED BACK OFF.WENT TO MY TRUNK,AND THE AMP WAS IN PROTECT.FIRST THING I DONE WAS DISCONNECTED MY RCA'S AND SPEAKER WIRES(STILL IN PROTECT)CHECKED MY GROUNDS(THEY WERE CLEAN AND TIGHT)CHECKED MY B+ AND GND(14.2V)CHECKED FUSES(NONE BLOWN)ALL WIRING SEEMS TO BE FINE.I CHECKED EVERYTHING FROM THE BATTERY TO THE AMP(HU INCLUDED)............ANYONE HAVE ANY IDEA WHAT MAY BE THE ISSUE?

I have spent an hour on google searching trying to find a neon light controller that will flash to the music using a rca cable so the neon flashes to the music and not people talking. I have seen them before but i cannot seem to locate one now that I wan't to get one.

I'm going to be running (2) 6.5 Alpine Type R component sets and i need to know what amp would YOU choose and WHY. Audioque: Amps: AQ4X90 Alpine Electronics of America, Inc. Alpine Electronics of America, Inc. - I'm leaning towards the PDX.

Here' s my current setup. Alpine 9885 (4V) Front: CDT CL-62 (160RMS) w/ Soundstream Rubicon 2.600 (180x2 @ 4ohm) Rear: CDT CL-69X (100RMS) w/ Soundstream Rubicon 2.250 (75x2 @ 4ohm) Fi BTL 12" D2, loaded (2000RMS) Soundstream Rubicon 1.2500 (2500 @ 1ohm) I want to add a duplicate set of CL-62 up front. The 2.600 amp is rated for 300x2 @ 2ohms as well. So I assume, wire the crossovers in parallel from the amp. + to + and - to -. That would yield a 2ohm load from the amplifier giving me how many watts per component at 4ohm each?

Lets start things off with the most info I can give. I have a 2006 Dodge Ram 1500 ST. It is a single cab 2wd with the V6 3.7L. The alternator is a 136 amp. The voltage regulator is built into the PCM. Now I am running a Soundstream PCX1500d and will be pulling the full rms (of 1500) during competition. I have a single run of 2/0 from front to back with 2 shuriken sk-bt60 batts under the hood. I am getting ready to do the big 3 any day. My current voltage is 13.8-14.1 on a normal day. When it is cold it will run 14.4. I want to increase my voltage to 15v. Now here is what I am currently investigating. I am in search of a wire diagram to find the feed signal from the alt to…

Ok so my friend needed an amp so i sold him my mrp-m850. And now im ampless but now i have an excuse for a lil upgrade. As u know the SSD12 is 800 rms. I'll have it in a sealed enclosure (1 SSD12) and im looking for a good bang for the buck amp around 200-250 max. I loved my alpine had no problems with it so i was looking at a alpine mrp-m1000 and their in my price range. Ohh and i only need it to run 2 ohms. U guys like that or noo. Suggestions please. Thanks, Vince

I have done some searching around and have not found out what I'm looking for, I understand the calculation for volts on a DMM to set the gains properly. In my particular case, I have (2) Fi SSD's (800rms/each) and a Sundown SAE-1200vD2 (1200rms). Now what I have been seeing is everyone says to take the lesser of the two then do your calculations for proper volts on the DMM. So, would I use 1200 from the amp or 800 from (1) sub or 1600 for both subs?? Im guessing since my subs can handle 1600 combined, I would then use the 1200 from the amp, which would be 34.64v (dual 1 ohm subs and wired that way). Please clarify for me. Next question, I have several wiring diagrams for…

Can somebody plz send me the link to the English version of SounDigital Thanks

so today i went to a car audio shop to get a 2 way alarm system with remote start. when the guy finally finished the system worked fine and then i realized when the car was off and everything locked.. the brake light and the front caution light wont turn off...... does anybody have any idea why this would be.... its almost 11 at night where im at and the guy told me to come back in the morning which means i have to disconnect my batt so it wont die and the re connect it in the morning.... CAN ANYBODY PLEASE HELP WITH THIS TOPIC..... im very frustrated right now..?????? thanks