Amplifiers / Head Units / Processors / Electrical

I'll be running 2 amps, how do I connect the remote turn on from both of them to the HU? Curious, thanks guys.

so i am going to get this out the way right now, if you don't have anything constructive to add please don't post. looking for serious feedback here. i am just curious and have an itch to know, so i am sorry if this seems like a stupid question to you guys. ok so i have a pretty decent handle on car audio, been in and around the scene for years, but most of my expertise in in other forms of electronics, now my room mate and i just got done installing a killer system in a friends cadillac, and we only have 1 possibly 2 depends on how messed up the other one is of the bass knobs we need. they are for 3 older series RF bd1000's. any way my question is what stops me from usin…

this amp http://www.woofersetc.com/index.cfm?fuseac...;product_id=517 OR http://www.onlinecarstereo.com/CarAudio/Pr...ProductID=19580 for an 18 inch fi q

i still got my fi bl 15" sitting in my room waiting to be installed into my 04 chevy colorado. my box is 3.9 ft^3 tuned @ 32 hz. i finally decided to go with sundown amps over rockford because i can get them cheaper. but i cant decide between the saz1500 or the sae1200. i can get the saz1500 $570 and the sae1200 for $350. i talked to jacob (sundown audio owner) and he said that the saz1500 is actually 1800 at 1 ohm and the sae1200 is actually 1500 at 1 ohm. will the bl be able to handle the saz1500? or should i just stick with the sae1200...plus its cheaper . im actually leaning towards the saz1500 but im afraid that it will be too much for my bl since im gonna be playin…

Does anyone in lower/central Michigan have an O-Scope?? I would really like to use one on my setup! I live in the Marshall/Albion/Jackson Area and would be willing to drive 100 mi. or so to use one!

Would running 500 watts rms or lower be to much on 8 gauge wiring?

do you think the Crunch GPV2000.1 can do 2k watts rms 1ohm at 13.8v but it only has 4 25amp fuses.. for 2 fi bl 15s? or should i just run 2 amps? GPV2000.1 1 x 500 @ 4-Ohms, 1 x 1000 @ 2-Ohms, 1 x 2000 @ 1-Ohm Maxx

i am looking for a decent reasonably priced o scope for personal use on my next set up and future sets... what brands to look for???

i finally took the plunge and vented my box...and i have noticed that the bass output changes per song or cd(which happened with the sealed box also)..some songs are loud and deep and others have nothing?..i was wondering if theses processors really to restore the low end in all recordings..im goin to get into the sd chips for music so i want everything to sound the same..thanks in advance...

I'm looking for a good HU that ranges from $100-200 and plays music via bluetooth with excellent sound. I have a 15" Rockford Fosgate T1 sub and a RF 300W 2 CH T3002 amp. I still need to replace both my front and back speakers. I love bass so I'm looking for a radio that has no problem with a lot of it.

here is what i am trying to run: (2) dayton rs1800 7" mid bass, (2) cdt es-04 4" mid range and (2) cdt tw25s. i want to crossover the bass at 800 and below, mid range 800-4000hz and the tweets 4000-20000hz. any ideas of a crossover or company that has the capability to run at these points. i have been looking at the 3sixty and some of audiocontrol's products. my h/u is an alpine 7897 and the amps that i have are zx650.4 and a 100.2. they will be put in a towncar. any feedback is appreciated.

Hi, need a small powerfull amp for one ssd 10 dual 2. I think about one Fosgate PUNCH P1000-1BD or one Soundstream Stealth Series STL1.1200D. The Punch is BD class and has 1000watts and the soundstream ab class and has 1,2kw... The amp has to be stable and powerfull but most importantly SMALL..... Whats the better choice?? Patrick

My bro wants to put a lil somethin in his boat while he is up in alaska. Since he is going to be in salt water, is there such thing as a 4 guage wire that wont corrode from the salt water?

OK i have never really bought decent speakers other than subs in my cars, and now its time. i would like to get a sax-100.4 from sundown to run some speakers. this will be going in an 06 scion xB. so my options are 4" dash, 6.5" components in front doors, and 5 1/4" coax in the rear. what are some good quality speakers that wont break the bank but sound great with 100 watts. i was thinking alpine type r's but i dont know. Should i ditch the dash speakers? and upgrade the others? thanks

I tried searching on two sites and couldnt find it, but what does running at full tilt mean? Like blaring the volume all the way almost (3/4ths give or take) or turning the phase all the way to 180 or whatever? I dont know why I thought so, but I've always thought it was turning hte phase up...

I current have a stock battery up front, and a batcap 2000 in the back near the amps. my question is, would there be any problems mixing battery brands? was looking at a kinetik 1400 to put up front.. would it make a difference? I would assume not considering the stock battery i have up front (wet cell) runs fine with the batcap in the back minus the voltage drops. I need to figure out a way to stabilize these voltage drops. Thanks guys!

I plan on buying a Hifonics 1606d for a DC lvl 4 18" i was wondering what type of electrical upgrades i would need i dont want to have to upgrade alt because of the placement of it. i would have to remove part of the tie rod assambly and the hearders on my car to remove

Hey im in the market for a new headunit looking to spend between $200 and $300. Functions i need direct ipod connect with controlls, Atleast three pre amp out puts, seprate sub control. I have been looking at the Kenwwod decks online but have nowhere around me to mess with them in person. Also considering Alpine and maybe pioneer but not really liking the button layout of the new ones. If some one could help me out i would appreciate it. Thanks

I have a 15" Rockford Fosgate T1 1200 watt sub. Could kicker ZX750 with the below specifications power it well? Also is there an amp that is around the same price range? -RMS Power: 375RMS @ 4OHMS 750RMS @ 2OHMS -Input: High/low input -Ouput: RCA output for additional amp -Remote bass level control Height: in(mm) 2 1/8 (54mm) Width: in(mm) 9 5/8 (244mm) Frequency Response,

Here it is..... I have a Defeat ON/OFF switch. If I have the Defeat switch ON the nulls all my setting on the HU correct. I want to bea able to use my Draconia crossover points and play with my EQ on the HU. If I set my HU to Defeat OFF, and set the crossover HP crossover points lower than the settings on my amp and my LP point higher than what I'm running, can I take advantage of my crossover points on the amps and still be able to use my para EQ? Example: HU crossover is set at 20hz HP and my amp is set at 60hz, do I get the 60hz crossover point?

Hello, i've installed my new(er) system the other day currently i have Optima Yellow top 2 SSA icons 12 2 Pheonix Gold Ryval 1000w 2 channel (each sub with their own bridged) 1 Pheonix Gold Ryval 1000w 4 channel 2 Kicker DS460 4x6 1 Pioneer DEH-P510UB Will be adding getting 2 Kicker 08KS6930 6x9 1 SoundStorm SX310 crossover if i'm not mistaken the crossover will prevent my mids and highs from "popping" and put a cleaner sound though, right? also is a sound processor needed? i have a decent amount of "road noise" coming though, just enough to bother me. will the processor fix all that? or will the crossover fix it?

Has anyone done this that could give me some advice? Any explorer within a couple years would be the same.

which is better, dls a6 mono amp or a sundown sae-1200D??

i think my alternator is dyin cause the voltage drops when im stopped...i need help on choosing a H/O alternator....how many amps also??

If I run 0 guage fron front batt to rear batt, then connect two amps to rear batt whats the best way....1} run single power wire to distro block fron rear batt 2} run an individual wire from each amp to the batt? Second part whats the best for grounding rear batt? run a ground back to front batt or ground to chassis or both? Also same question on grounding my amps ,to the rear batt or on the frame?