Amplifiers / Head Units / Processors / Electrical

What gauge size are the power supply connectors for the sax-1200d? thanks

Hi everybody. I recently had my starter set up installed (2 sa-12s dvc 1 sax-1200 wired to one ohm). It was not hitting hard and then it just went completely inaudible, although bass was still slightly there. I realize the not hitting hard part was most likely a wiring issue. I took it into a car audio shop, we opened it up and the guy told me that i blew it, still very puzzling. The gain wasn't set beyond half way and I blew it, but have no idea how. Anyways, I put a picture below (downloaded from the net) and circled the place where the seal broke, and the guy who installed my stereo said it was faulty. Now the problem is bigger because I live in Taiwan, so i was …

I am just completely stumped with this problem. I'll try not to make it long but I want to make sure I explain everything right. I have two amps in my car. A Rockford P500.2 and the SAX-1200D. Both have their own runs of power wire and grounds. The Rockford has 8 gauge going to it, as nothing bigger is necessary, and the 1200D has 4 gauge running to it. Yesterday I completely redid everything at my battery. I had to get new battery terminals, as mine were meant for a top post battery, and rewired the factory ground and such to the new terminals. That went smoothly, car starts without any problems now (had some bad issues). My battery tested good at autozone. I also …

Is a SAX-125.2 amplifier enought for a FI 18'' 1000w sub. Or i should go bigger. New in this stuff and would like some help to decide.

Hello I am an amateur stereo guy in need of advise on setting my amp. I have the gain set to 21 volts on the front and rear of 4 channel with a 1khz test tone I have the gain set to 41 volts on the 1500d amp with a 50hz test tone Those settings were given to me by a friend My question is where to set the crossovers? the low pass/high pass filters the subsonic knob and the 2 push in buttons I currently have the front channel run on the crossover on the head unit set to 100khz with a 24 slope Rear channel is off on deck, and set on low pass on amp but not sure what the settings should be on the amp, the deck does not give me a low pass option on rear channel The sub is cur…

Need help deciding between the sundown saz1000d or the rockford t1000-1bd(09 edition). Will be going on a Fi Bl 15 dual 2. The box will be 4 cubes at 32 hz. Any help is appreciated

Hi and Good Morning. I am trying to come up with an amp to power my Digital Designs 1008 sub. It has been rated at 500 continuous and 2000 peak. I was told to make sure to get an amp that will supply at least 500 watts rms but i am considering running two of the 1008's or two of the 1508's by Digital designs. I have heard many good things about both of these amps the Sundown Audio SAZ 1000D.1 and the Precision Power P1000.1. Can anybody give me some great advise here and thank You very much.

i bought a saz 1500 and it didnt come with a bass knob.anyone have one that i can buy???

just wondering if there is a way i could tell the difference between the saz 1500d with the new heatsink design and the old. thx-phil

I just got a saz 1500d and am trying to get the gain set just right. With nothing hooked to it and at 27/35 volume, bass -2, sub -2 and with the gain set 1/2, my DMM reads 60.8 volts. This seems way too high but it does sound pretty good on my dd 3512 wired to 4 ohms. Only thing though, 60 volts would be equal to 3600 watts at 1 ohm. Am I doing something wrong or is this the baddest 1500 watt amp in the world?

Hey People....I will soon be the proud owner of the SAZ 1500D!! I am wanting to get your advice on how to properly power the amp. I currently have a car with the stock 105 amp alternator. I've done the BIG 3 with 4 gauge wire. I also have 4 gauge running to my trunk.....It then goes into a capicator and then to a distro block where I have it going to a 2 channel 300 Watt Denon amp and also what will now be the SAZ 1500D.....I'm pretty sure that I will be starving the amp for power....SO...My question is mainly budget related. How can I give the SAZ enough power the cheapest way??? Can I run another 8 guage power wire and just use it for my 2 channel and leave the 4 g…

well i got my SAZ 1500d in the mail a few days ago... and now i have my 1/0 gauge Tsunami amp kit to replace the 4 gauge from my old sub amp... so now i am getting ready to install it all, i was just wondering if anyone had any good sugestions on where to set the subsonic and the LPF knobs ? and i a guessing to leave the phase off.. this amp is to run my 15" Xcon.. it is in a 4 cubic feet box ported to 32 hz.... i figured there would be someone here who could get me close..

Just wondering where I can purchase this amp?

So Im new to this but i have an 86 chevy suburban i want to have it banging harder than anyone eles in the hood. so im planing on getting two fi ssd 18's and i dont know if i should get a sundown saz 2500d or a saz 1500d please help i just have stock battery and stock atl will i need upgrades if so what do you rec

Ok guys i got my saz 3000 order in just waitin on new ones to come in and i've ordered a 18 btl what i'm wondering is will the 220amp "Dominator" Series Iraggi Alternator be enough with a extra batt and if i deceide to go with another saz 3000 would it still be ok thanks for any help ahead of time.

hi im new her and from sweden, my englis is´t so good so i apoligist for that. now fot the question, is ther anybody who know what 2 saz 3000 strapped giws out in 0,5 ohm mwh from sweden

saz 3000d vs IA40.1 give me your thoughts on a 14.4 @.5 ohm setup

Hey guys, I was wondering about the difference between these 2 amps. My box for the 2 18" Btls is in the proccess of being built, and I am entitled to pick up 2 Powerbass XA 3000d's for 700 bucks a piece (brand new) and I was wondering if they are the equivilent to the Saz 3000d's and will perform as indicated? http://www.powerbassusa.com/products/ampli...xa_class_d.html http://www.sundownaudio.com/3000d.html thnks, Freddy

Does anyone have any idea what the saz-3500d would put out watt wise at 1.33ohm while being fed 12v?

I currently have L7s, I was going to get a FI Bl. But instead I think ill just keep them for now and I was wondering is a saz 1500D, capable of powering two 15" L7s? or do I need more power to them?

I am looking to build my first system and I am a full believer in saving money but not at the expense of diminished quality. I want to get 2 15" BL's. This is in an every day driver, I want it loud but it doesn't have to be insane. I know that install is 90% of it so I am wondering how much of a difference am I really gonna see if I have Sundowns 1500 powering them or the 3000. Saying the encloser and every other factor is the same. I am thinking that since I am not looking to compete I would be spending way too much money buying the 3000 and all the extra electrical upgrades that are needed and not have that much of a noticeable difference. So if anyone who has experienc…

I'm going to be running a SAZ-1500d at 1 ohm on a 15" FI BL. Question is, i have the big 3 done in 0 gauge and a optima red top in a scion xb with i believe a 80 amp alt (stock). will i have any problems? I plan to get a 200 amp alt and an extra battery but would like to wait if my electrical can handle it. thanks, Justin

I have 2-12w6v2d4's and i just bought a saz-1500d. My question is will this amp blow my subs and also is there anyone on this board who has ran this setup? I'm thinking if i keep the bass on the amp down it will be ok am i wrong? Thanks in advanced for the help.

alright so theres a problem that bothers the hell out of me I want an amp I am stuck between the sundown saz-1500d and the audioque aq2200d. the audioque does 2200 at 14.4v Im aware that that it would be almost impossible for me to keep that voltage .SO my main question is which one to get does anyone know what the audioque will put out at like 12.5 to 13 volts thanks for the help guys.

hey whats up i need help choosing an amp(s) for my setup, my electrical upgrades are big 3 1/0 gauge, 2 runs 1/0 gauge 1 pos 1 neg, 200 amp alt, optima yellow top front,die hard platinum p1 in back, k i have 4 dual 4 ohm subs kicker 15 15's, i need an amp decision i either want a saz-2000, i would have to run it at .5 ohms will my electrical handle that, and hit hard, or should i go with 2 saz-1000 and both amps would be wired down to 1 ohm, which setup would b louder and which would work the best