General Fi

Currently im running a 12" Q ported (2cu@32hz) off a saz-1500d. Im looking at trying to get more output but am limited on space. Im looking at the option of doing 2 SSD 12's sealed with 800wrms going to each. How would output compare to the Q ported? I have about 3 cubic ft to work with in a sealed box. I could also possibly do 2 10" SSDs ported but only in 2-2.5 cubes. Any recommendations?

I have a pair of Q 15's that I have had since november 2006. I had them in my old 89' Range Rover in 8Cubes tuned to 30Hz. I loved them like that. Well I just got a 1995 Integra hatchback. I have them sealed 5.1cubes after disp. and WOW. I thought they were a nice driver before but being sealed they are on a whole other level. I just cant describe it. The bass is so accurate, smooth, and beautiful sounding. It just sounds 'solid'. They play lower and also hit the higher frequencies better. They play so much flatter (not peaky). Being in the hatchback, they are also louder to my ear and definitely moves more air. Here are a few vids of them in the Teg. There are also …

15" Q on a old school memphis 1000D, quality was alot better before youtube but then again tis my first vid

after gettin the body work fixed on my truck (was rear ended last week) one of the guys from Vices autobody wanted to hear what it had. I wonder how they knew i had beat anyway, if you guys are tired of me posting so many vids just let me know, its not my fault i get stopped every day almost for a demo.....sometimes i film, sometimes i dont..its better when someone else films though i can concentrate on what im doing. also if you look in the vid its hard to see but people came out from across the street in the other buildings cuz i was makin so much noise. Thats where i panned over and started to snicker a little NA0-wnWzf6M oh, when i get it on the site it will be m…

Hey i have a bl 18 powered by a jl 1000/1. all electrical upgrades are done (upgrading soon) anyways the sub saw 750 watta at the most, it was not beat at all. The other day it cut off in the middle of a song. When i pulled it out i saw that one of the tinsel leads are broke. How would i go about fixing this? is it covered under warranty? would soldering work? Thanks for the help

I'm just lookin to listen to some. Please.

hey guys i have a ava motor that the top plate has came loose. i was wondering how much it is to repair this and how much would a 15in recone run? but with maybe a stiffer spider and 4layer flatwound coils cost?

Scott/Nick i sent you guys an email the other day about reconing my 18's and how the new tinsels are? and whats up with the Fi appearal? Thanks John

i am making an spl box and going to get into a few small comps this summer. i am going to tune the box to what ever my car is tuned to (not sure right now) the bigger the box will i get a higher number? i will probably end up making it a removable port so ill have something for street beat and for spl. SPL IS THE MOST IMPORTANT! so how many cuft? its an 18 BL fully loaded powered by a rockford power 1000.1 in a VW golf

Hey I emailed sales [at] FiCarAudio.com 10 days ago and then emailed Nick and Shawn a day later. I still haven't heard back from anyone. I'd like to order a Fi Q 10" no BP Option. I can't place the order via the webpage because I'm in Hawaii. I know shipping is going to be more, thats okay I'm ready to order now. Please get in touch with me. I emailed the request from dj.kickz [at] gmail.com

I figured I would post up a few vids a friend of mine took of me beating the crap out of my truck this weekend at Spring Fling...Enjoy Scott,Nick and Shawn....If you guys have a tent at SBN this year I would love to stop on by and give a few demos.. ..if thats ok

You may see me browsing but i'm not going to have time to post i'm not ignoring you, i've got the wake tonight and the funeral tomorrow and after that it's work on the truck 12 hours a day... I will be slow to reply to emails because i will be up and down the road all week...just have patience Thanks -Nick

hey guys i just placed an ofer for a loaded BTL 15. i couldn't add any notes anywhere but along with the order could i get some decals and some flyers? thanks!

Would 2.3 at 33hz be good for a 15 bl.

I have 2 04/05 RE XXX motors. This summer i wanted to recone them to DVC 2ohm 12" and i was wondeirng if fi offered a recone kit so i could do it myself that way i wouldnt have to pay for shipping to fi for each of the motors. Also how much would it be? Thanks.

i was emailing scott and or nick about a 18" basket and recone kit for a fully loaded btl 3rd mag dual 1 ohm daily option, and we got as far as scott asking for a zip for a shipping quote and i did reply back... 2 times... scott/nick if you guys dont mind could i get that shipping quote? if you dont feel like digging through emails my zip is 55407, Thanks. email is [email protected] (yes i know its a ghey sn but its old and use it for allot of stuff) lol

ok i am a big time noob to box's, but i do know ported is more spl and sealed is LSQ. For a BL you need to go ported. But for a ported box which would be the loudest out of the 4 combinations, small box small port, big box small port, small box big port, smal box small port? all i am concerned about is spl/loudness. (it is for a 15 BL.) thx.

I think someone had a file with just the Fi logo on it to try and make some decals so can some one post the file or link

if anybody out there has the new btls with the new tinsels.. i just wanna se how they look like thanks.

I can purchase two blown konaki 12 subs for 40 dollars per woofer and was wondering if I could send it in to Fi for a recone or purchase a recone from fi, I know you have to replace the basket as well... but if I can recone them for cheap it would be a good investment I think.... Thank you for any advice in advance ~ jonathon. (oh and these look just like the audioques just as a reference to which subs i am talking about)

The other day I whiped together a box for my Q10, 14x14x12, 3/4in mdf, comes out to around .9 cubes. I screwed up on one of the cuts so i just siliconed the chit out of it. So i have it in my truck now, pushed by 900 kenwood watts rms and there is a clicking noise coming from the sub. Not so noticeable on the lower notes or in rock songs, but it really makes me mad. I pushed on the sub, no scratchy sound, i put the coils on a DMM, both at .8 ohms. WTF! I also tried it free air a little and the noise is louder let. I read on another forum to check my spider for rub marks from tensel slap, and i couldn't find anything. Any ideas? Am i doing something wrong?

do I have to worry about window damage with two 12" fi bls?

I ordered 2 fully loaded btl 18, sent out emails about shipping or when there are to make it to me no responce back. Any back up, delays for any reason please let me know Thanks

hi i have a quick question, the btl line dont have extreme leads like the bls??? I AM A be getting a fully loaded btl.

So yesterday I finally got around to making a new box for my 12'' Fi Q D2. The box came out great, but when I went to put the Q in I noticed one of the tinsel leads was broken at the end where it connects to the terminal. I'm not sure how or when it happened. The gain on my amp (US amps XT4000D, 1500rms @ 1 ohm) is set about half way up and the bass boost is off. My question is what can I do about this? repair it? send it back for repair? Any help is appreciated, thanks