Subwoofers / Speakers

I have a 15 inch Hyfonics goliath quad coil sub that the spider surround came unglued and it fryed the sub. Does anyone know where I can get a recone for this sub?

Ive had my 15" in a 4 cu/ft box ported to 28hz My friend has his XXX in a 3 cu/ft box to 34 hz I like his cuz it hits the lows nicely without distorting. My prob with the 28 hz at 4 cu.ft was some songs sounded horrible. What box would sound the best and get the lowest for rap music?

I hooked up my type r 10 and the it didn't get nearly as loud or play as filling of bass as the Icon did, the icon was only at half gains on the rf p1000bd, it almost seemed like the Type R was really hollow or something. I played Speaker Boxx by Outkast and the type r hit pretty well but it just didn't sound that great, (also, the type r is dual 4 ohm so I hooked it up at 2 ohms and turned the gain all the way up, the birthsheet says 825rms @ 2 ohms) then i swappedthe Icon back in and turned the amp down to about 3/4 of the way up (700 watts if the amp was not underrated, birthsheet says 1310 rms @ 1 ohm) and I put Speaker Boxx back in and I couldn't handle it, it was …

What's going on. I'm looking for some advice. I have been looking at Elemental Designs 6000s comp and 9.2 amp. Does anyone have any experience with them or have any advice they want to give to me about them cause I have seen mixed feelings between forums. Thanks for the help.

i have been looking around on the ssa store and am intrested in gettin 1 15inch sub in a ported box. i saw that the packages are alot cheaper than buying seperatly. which package is better for spl the xcon or sundown nightshade D2 both with a saz1500d. the xcon package is 819 and the sundown is 899.

Ok. I'm starting back into audio but thought I'd start off with a decent boom/bang. Looking mostly for SQ with a little SPL. I already own a "brand spanking new" Zed Audio Kronos, pre-ordered a Stereo Integrity BM Mk V (I'm kind of limited in space). I was thinking of adding a SSA IC 150.4 and a set of 6.5 Evil Mids(I guess 8 ohm versions) and Evil 1 Tweeters. I am looking to do the following setup (all in a 2010 Hyundai Genesis Coupe): IC150.4 - Ch1 and 2 to Evil 1 Tweeters (maybe mounted to A-pillars or factory door location) IC150.4 - Ch3 and 4 bridged to BM Mk V (debating on how I want to set this up; either wheel well or leaned against the front of tru…

96 civic coupe with an aq2200, optima d35 yellow top up front and a kinetic 3800 in the back (overkill?) with a 200+ amp alt (havent sourced yet). plan is to seal off the trunk sub n port goin into the cab. box wise im looking at 5 cubic ft or so after port and sub displacement. so... 2 fi q 12's or 1 btl n2 15? both would be fully loaded (cooling and extra spider for the Q... high xmax coil and cooling for btl.) i listen to alotta stuff so im thinking tune the port to 33-35? if you guys have suggestions other then those please lemme know. thanks!

i currently have 1 dc xl 15... should i buy a second one and do the wall or should i keep this one save the money for more power and do a slot or aeroport box in the trunk no backseat or just sell it for something better

I currently have 2 kicker cvx 12" subs in a crappy prefab box and I'm looking to get louder and lower (move a lot more air). I cannot decide between getting a custom box for my subs tuned to the low 30s, or getting 2 type r 15's, or one nightshade 15. which would give me the best results? the type r subs would have to be in a prefab box

I'm currently tinkering with ideas for my front stage. I'm looking for a particular sound and I'm not sure how to describe it but here it goes.... I have a set of Grado Sr80i Headphones (which I HIGHLY recommend to anyone who loves music) and they have lots of....shimmer? on the high end. I want that sound for my car. I want the higher midrange to be pronounced, I want to hear the details (such as the rasp in men's voices) and I want it to be pretty loud. I have a cheap bookshelf setup in my room and it has Piezo horns in it that have the sound (as far as highs) that I'm looking for. The best I can describe it is airy, or wispy? A very exciting sound. So with that said, I…

I like being able to comfortably fit two golf bags & pull carts in my trunk. A free air install in the rear deck would allow me to retain the vast majority of my cavernous trunk. Having only played with the idea in a large enough wall enclosure that it may as well have been free-air, I'd like to hear experiences. It wouldn't be a huge loss to tuck a 1.5' box in the trunk, so if infinite baffle is more trouble then it's worth, please say so. TIA Nick woofer specs: FS: 47hz Qts 0.593 Qes 0.635 Qms 8.935 Vas 3.34L Wrms 500 The suspension & motor control are strong. I know what BassBoxPro says, I also know its incredibly outdated, thank you though.

hello all, i currently have one dual 2ohm xxx15 in a snail shell designed enclosure wired to a bx1500d at one ohm. ive had this setup for about a year and it is very loud and sounds very good, but with this hobby, you all know how it goes; you always want to try something new and im still quite the bass-head.. ive wanted to try ddaudio for years and i think its about time. so, i was wondering if any of you guys would recommend the dd3500 series. ive always been a single-sub kind of guy, but 2 12s sound so intriguing because of the added cone area over a single 15, especially that of the dd variety, though the 9900

So, lately Ive been asking a lot of questions about subs that I've been interested in. I've narrowed down the subs to just two choices 2 Sundown SA-12s or 2 Fi SSD 12s. After purchasing the subs I plan to build a ported enclosure and purchase an amp. I want loud subs with deep bass. Tell me which subs you would go with and why. Also if you'd have experience with either subs. Also would like to purchase an amp under 300$ that's 1200-2000 watts any suggestions. Thanks.

for the Mach5Audio IXL can you add any other options to add to the power handling? i like the IXL but need about 500 more watts of therm. power handling to add to my SA 3kd

I just installed my new IA 6.5s comps (2 sets) using the rear 2 mid bass only, they are on the IA 6.4 amp, they sound really good but when I try to get the right mid bass coming thru one has a pop to it, and they are just not as loud as I think they should be,so I am looking into the rainbow CS 265.25 just wandering if anyone here as any experience with them , and are they louder than my current set up,I am also using a death row 12 in a sealed box( yes sealed ) and it sounds great it does not miss a beat it is in a 1.34 cu box , any suggestions would be appreciated , 2000 celica

so does anybody have any vids of there mj-18's yet? I cant find any new ones? I would love to see what other people have there mj's in and what they can do to there car's/SUV's/what ever..

is there such a thing as 4" or 4x6 drivers that can handle midbass or are these things just not meant to play it? If so who makes one?

Would a US AMPS MD1D (underrated 1200w @ 1 ohm) be to big for one IXL 10.2.2? Will be putting it in a ported box not sure what size yet so any recommendations would help. Thanks

I've built a couple of hundred boxes all the way from 2 6w0s in a Ranger to 3 Shockers in a 200SX wall(12 10"s earlier in the same wall) and 8 12"s in my Eclipse I used to have, as well as the run of the run of the mill multiple 13W7s, JUGGS, 2 12"s and everyday beaters middle of the road subs, as well as helping db drag and MECA guys at any opportunity cause that's how I get down to always give a helping hand. Now that I finally got a job my next future woofers will be beasts and I know simple screws will shear and break. My problem is (and I have TRIED T nuts before with dissapointing results mounting them) I need you guys' help. If anyone can take a few pictures an…

What I have right now.... 2 Sundown E-12s (400rms version) Hooked up to a 1700.1 Hifonics Amplifier at 1 ohm. Inside of a custom box made for the Ford Mustang Convertible, .9 each sub, sealed. Well, isnt that too much power? yes it is! So obviously the gain is way down. My question, Would I benefit from switching the subwoofers to something that can handle more power? The problem: If I do get new subwoofers, the mounting depth can be NO MORE than 6.5 inches.

Ok so im thinking about cuting holes in my door panel for my 6.5s Apline type R's So i can show the grills instead of leavingthem in the factory spot (08 Pont G6) . i plan on using a hole saw, would there be a better tool for that instead? and if i do that then i think the sound and performance of them will og down without some type of addend or extra install to go with them, especially with that small space between the door panel and the factory location, what could i do to ensure the SQ of them and performance? sound deadening maybe? or what could i put to fill that gap and etc.

I got a Memphis M3 10 (2008) and its def. blown but it still barely vibrates and makes the faintest bass when I turn it up. What does that mean? I already ordered a recone so I was just wondering if it would be possible to fix? The coil looks fine and both terminals still have the correct resistance. Tinsel looked okay but I didnt really look that good due to it being a bulky 10 so its hard to see anything. Anybody know what it might be and how to fix it?

I was looking at the FI BL 18 for the price but I am really wanting to try the Sound Splinter RL-P18, Plans are 2 18s in a wall, what does everyone think of the two (pros,cons,what you like about which sub) thanks for any input provided.

Simply, can you have too much motor force on a subwoofer driver? If it is application dependent, I am referring to applications where music is being played, and if that isn't specific enough, let's say C&S songs. Decaf, all that stuff. Just curious, thanks!

ok. i built my boxes (still unsure about the subs), and the port came out looking funny. I'm almost sure, but just to be extra sure, i figured someone could help me out. when i ported my boxes, i took the cubic inches of a different boxe's port (3 cubes at 34 htz) and used the same on my 3 cube box (also at 34 htz) the difference is that it isnt as deep, but longer... even though the dimensions are different, because they both have the same cubic inches of port, it's still tuned to the same freq, correct? thanks