Incriminator Audio

I am building a wall in my car for my 2 new 21 inch dp's I wanted to know if anyone could recomened box size and port size I was thinking about tuning it to 33-37hertz any help would be apperciated. Thanks

sry videos r so crappy will make mpre this weekend or maybe at some upcoming shows let me kno wat u think

box is abt 23 cubes 19.5 after port and sub displacent will be tuned at 31.75 powered by 2 sundown saz-3000d's enjoyy let me kno wat u think

I got my 2 21" Wardens in last week, and they look amazing. I ordered through Vertex Audio, they were great to deal with and kept in touch well. I had the pleasure of talking to Nick and he was helpful, and courteous. It's really nice to hear a real person answer the phone. Anyway, I'm going to be running the subs on an American Bass 1000.1 at 1 ohm, so give or take more than 10kw if I can keep imp. rise down. I have more alternators on the way, so for the time being I'm running the amp at 4 ohms, roughly 5kw. I just got things hooked up today and even on RMS these subs are performing great. They're every bit as loud as the 2 BTL 18s I had at 2 ohms a month or two ago. …

http://www.youtube.com/watch?v=79MRbHXRsJI

Here is a little install that Nick and I did today for his cousin.....Haven't had it metered, but by ear its in the upper 140's at a pretty low note (box is tuned to 32hz).

I will be powering these with a 40.1 once I get it back from Nick, my question is, which will be a better setup for daily? I'm looking for SQPL as I don't want to be limited to only SPL. I've heard that the DP's are good daily subs but the DR's are good daily subs also. Either will be in the recommended enclosure and tuned to 30hz for the lows. So what do you all think will be a better daily combo? thanks

Is it possible to get 2 dp 21s n a trunk of a 95 caprice???

This is a project I have been working on for some time now and it will continue until everything is the way I like it. There is a lot that is subject to change and will change in the upcoming weeks. This will be a permanent setup but it will only be in for a short while. I still have a lot to do to the interior so some things will be out of place. I have part of the big3 done already and I have the materials to finish it. I have a couple of batts for now and they should hold me until I either upgrade or find another amp like I already have. I will also be upgrading my batts in the future. I hope you enjoy.

I had a thread in build logs but since IA is going in it I figured I would post here. It has 2 12 Dp's in a transmission line enclosure

hey guys, I'm in a project, i got 2 IA deathrow 12" , I was planning to build a box for the 2 subs in a single common chambered box? can the box handle it? the box will be slot port on 38 htz. any suggestion? TIA

So did I mention we released the 20.1 on the 1st, the plan was to start shipping Monday the 3rd, but I didn't know SEMA was that week and I didn't get back to the 11th. so we've been shipping a week today.... I didn't know if the word was out or not..... Sorry for the late update, I've been making up from missing a week or so for SEMA. Pics soon...

I have two ia 20.1's pushing two ia dp 21's currently I have one sub on one amp@1 ohm. But I'm only geting 1400w @ 14.3v. The impedance rise is is going up to 2.58ohm. I was thinking about rewiring them to 2 ohm and strapping them. Would that help get more power out of them? Or????? Thanks for any help

OOps never mind original plan is back on!

Can a 20.1 operate safely for music "ie bass race or drive by" @.35 ohm on a 16+ volt system?

1) do I have to connect the 2 inputs like in the diagram, or can I just use one ? 2) I am assuming the 2 speaker outputs are in parallel, so connecting a 2 ohm load to each set will result in a 1 ohm load to the amp .... ??

Nick- Do you know of any shops in the DC/Maryland/Virginia area that can repair a 20.1 amp? I would prefer to send it to you as no one knows them better than you. I sent you a few emails but just in case you didn't get them can you reply back to brandon.nicholson(at)dot(dot)gov. I'm not for sure what happened this time. It looks as if the power supply may have went out again as the same pieces on the outside edge are burnt. Before I installed the amp this time I had all the wiring re-done professionally. I'm dying without my baby lol. Bass is my Anti-Drug lol. I just received my tax check so repair money is sitting and waiting. Thanks

Death Penalty Series with MSRP - 12" ($599), 15" ($639), 18" ($689), and 21" ($799) Dual 1 and Dual 2 ohm Standard Black Cast Basket 3" 8 layer Flat Aluminum Voice Coil Triple Black Progressive Spiders with Woven Tinsels Non-pressed Kraft Fiber Reinforced Cone Double Layer Foam Surround Triple Stacked Magnets with Black Nickel Finish Interlocking Aluminum Spider Spacer Assemble CILD - Center Interlocking Dustcap Design for Easy Field Recones ADC - Air Driven Cooling - 6 Aluminum Column Vents for Max Motor Cooling Silver Push Terminals Wrap Around Rubber Gasket The wait is over! The last missing part will be here Friday, so expect pictures this weekend, if not it will be M…

Just wanted to say Thanks to Chad Hicks for the Review! __________________________________________________________________________ Full Review: Listening Test This subwoofer is definately a beast, however it is not a pure spl sub. The amount of cone control this driver has is amazing. Testing in a 2 cube sealed box and in a 2.7 cube ported box ( 1 6inch aero tuned to 35 hz ) yeilded some interesting results. The sealed box lacked output, no worse than any other driver I have used, but it did help the low end of the driver a bit. Ported is where you should run this driver, as it is a monster. The 2.7 cube box i believe was a decent match with this driver for daily use b/…

I wanted to know where I could find two of the DP21 motor and basket assemblies and what would be the price of them be? Working on a project and I know you guys can help me out.

The new 187 will be released around CES. It will come in 10, 12, and 15's. All units will be Dual 4's. The new 187's will be super sized! No more bumped back plate and single small magnet slugs. They will now have a huge 6.25" double stack motor with woven leads and push terminals. Forget all the other entry drivers.....in the $100 range, if you've heard the old 187, you'll love the new one..

Yesterday ,I won DB4 at Meca world finals with a 127.9 db using 4 18's no wall and only 2 old school IA 20.1's on 12 v system.

Anyone ever tried a 4th or 6th order for the 2010 line of Death Penalty 12? I figured for a 4th order do a 1.5 cubes sealed and 4.5 cubes on the ported side would do decent, but looking to see if anyone has ever tried it. I wanted to base it off a 100% spl setup with interchangeable ports to swap tuning to 32-34hz for daily.

I saw a thread somewhere about it but can't seem to find it. Any more info on these ??