Fisher Customs

I sure have been building a lot of large boxes lately. Im kind of ready to get back to some smaller ones... haha. This one is with a side firing port. I have done 2 other enclosures for this customer with the same port configuration.

i need a new box design for my btl. can i get a responce from someone on how to do this. i dont know how much it cost. i have money and i need just a design thanks guys.

Hello, I'm not sure if you remember me but I e-mailed you guys a few weeks ago about a box for two 10w6v2's, well I sold those and will get a 13w6v2, I'm hoping you guys can just build a simple sealed box for me. I sent you guys the 25$ for the design and I am waiting for a reply. What do I do now? I emailed chris(at)fishercustoms(dot)com, just waiting for a reply. Is there anything else I should do? Did I do everything correctly?

This is a sealed box built to JL's specs. Will end up being bare.

This is the twin of the other sealed box with the Passive Radiators I did today. It will also feature a raised "G5" logo on each side panel, and will be finished with carpet.

This is a standard 4 cube sealed box for a pair of 12" (BL's maybe). The customer will be lighting the front with a neon, and wanted a little home for it to direct the light down the front side of the box. It will be left bare, and be color matched to the vehicles interior later on.

Something kind of crazy happened here. I dont ever recall doing an enclosure with some PR's. Then I did 2 today, haha. Both are the exact same specs, except this one chose to add a double baffle. Onto the pics...

i need a ported box 4.0 cu ft tuned at 32hz for a single 15 Q, is this a good enclosure for one? also is the crx style good? how much am i looking at? i need it shipped 2 houston. who can i get in contact with?

Greetings All!! I've seen the boxes made by Fisher Customs and I must have one!!! I'll be purchasing 2 RE AUdio SX15's and I need a CRX style enclosure to do them justice. I don't have the dimensions on my vehicle and I was curious to know if an enclosure has been made for a Tahoe previously. I'll also be pairing them up with a Kicker 2500.1

This is a nice little 1.0 cube sealed enclosure after displacement for a single 12" Mag v4 I believe. It will be finished off with carpet, once I get the compressor back up and running. Here are a few pics.

Have you made an enclosure for the crew cab titan? Im doing a seat raise which gives me roughly 11.5-12" of clearance from the front of the seat to the floor, and 8" in the rear. I want to fit a beefy 10" like the Adire Brahma, or RE SX or FI BL.....do you know if I will be able to manage this? I wanna do a ported box for 1 10" sub.

Not sure if those are the exact specs, just going by memory on this one. Pretty straight forward box here, with a 8* angle on the front panel. Will be finished off with carpet.

Anyone have any ideas how to make my box slant at the top and bottom and port in the middle, box is 21 cu. will that work by the way?

Dont recall the driver, but this is a pretty standard slot ported enclosure. Double flush mount baffle, and will be finished off with black carpet.

I have 2 dual 12" Alpine Type R's...I've been told that ported is the way to go for these subs. There is a problem though. My trunk is small as well as the trunk opening. Right now I have a crappy sealed box 38"W x 10" TD 14" BD x 14" H...it has two old MTX subs in it right now. It was a pain to get in because the height of my trunk opening is 14" as well and the width is 35". I've made a few designs in photoshop but I'm not sure if they'd work due to my lack of knowledge in this area: I'm not sure how many cubic feet will be needed but I'd like the width to be around 30" and the height to be less than 14". Again...these are just some ideas...not sure if they'd work...…

This is a 3.0 @ 32 hz enclosure for a single 15" Fi BL. Crx style, with a double baffle. The box will be left bare. All that is left to do, is sand it up, and the badge and terminals, and then get it ready for ship.

Very simple sealed box here, wanted to post the pics up for the customer.

Hi i know this is perhaps a little off topic but was thinking when you use fibreglass or carbon fibre as detailing on a box(around the port area and front pannel) will this stick to the wood or will this cause some nasty rattle or something? if this is possible what would be the trick behind it? thx

This is 1 of 2 pretty cool builds I have going on right now. I thought I would share both of the logs with you guys as well. Hope you dont mind.... Some of you may have seen the other thread about this box... http://www.caraudio.com/forum/showthread.php?t=282794 But basically, its underway now. Got the panels cut, port areas painted, and sketched out the brace. More pics will come in the coming days.....

This box is going to be so kickass. dylan is awesome at designing this thing, i wont post the rough pics unless he says its alright, but I'd be interested when this bad boy is built, to see a build log of it! Thanks BJ and dylan for all the time and work you've already put in!

Title has the specs. Will have a center located port, which will be painted red. Will get finished off in black carpet tomorrow.

I believe this is for a single 15" Nightshade. Will be finished off in black carpet.

This box will feature a flared port, and a top mount double baffle. I believe it is for a pair of Type R's. Will be finished off with charcoal carpet.

Dont recall the driver for this enclosure, but it will be finished off in black carpet.

Not sure on the driver that this will be paired with for sure. This will be double baffled, with driver firing forward and port up. Pics...