Fisher Customs

I'm needing some box plans for a upcoming build, and I'm hoping you could make some for me, or lead me to someone that can make a set. But, I'm wanting to make a rear loaded folding horn for a single SS 12" RL-p. Is that something you can pull off for me?

Not sure if those are the exact specs, just going by memory on this one. Pretty straight forward box here, with a 8* angle on the front panel. Will be finished off with carpet.

everytime i come to the ssa forums i always come to check out this box http://www.soundsolutionsaudio.com/forum/i...showtopic=22072 ... i will be running 15 nightshades soon as i get the 12's reconed to 15's. that box is ideal of what i am trying to get built but instead i want my subs and port facing back with the plexi windows on top... my zip is 70501

I sent an email about 2 weeks ago through FC's website and have not received a response. Are enclosure still available? Please contact me at [email protected] so i can give my contact information thank you.

I just ordered a Fully Loaded Fi BL 12 to put in the trunk of my 06 mustang. I have been looking at your builds and really like them. I was wondering how much it would cost for a box around 2-2.3 cubic feet tuned to 32~35 hz? Also, I would like to kinda customize it with an Fi logo. But thats not as important as gettin the best possible box. Thanks

do you guys have any experience with boxes that go underneath the back seats in a dodge ram that is between the years of 1994-2001? thanks!

This is a build for 4- 8" L7's. Customer sent me design specs, I believe around 3 cubes. He will be installing the 6" Port himself. Here are the pics...

I have a 2007 mustang coupe with 2 12" audiopipe TXX-ap12bl in a bassworx pre-fabed enclosure right now..they sound alright in it..get pretty loud..but i want a custom enclosure for them..there powered by an audiopipe ap15001d..im looking for spl..and in a good enclosure..i belive these subs can do just that..now the only problem is the trunk opening on the new stangs...are a little tight..i had to do some fabrication in my trunk to get the box i have in there now..but i was thinking somthing like a 3.5cuft enclosure tuned at around 34-36hz..

If you ever get enough time, you should post a "how to carpet a box properly" thread. Just an idea.

This is a sealed box built to JL's specs. Will end up being bare.

I am just curious to know what the difference between flared and standard slot ported boxes. Obviously outside of appearance is there any performance difference???? I am looking for a nice ported enclosure for my 12" AA Havoc.

Dont recall the driver for this enclosure, but it will be finished off in black carpet.

First off hello everyone. I have been browsing the forums for a while, and i really never post. I guess got a little too excited and sent payment for an enclosure before discussing it on here. haha the enclosure was for two alpine alpine swr-1222d's in a 4 cube enclosure @ 32 Hz. my question is, what would you (or anyone else) recommend for tuning. is 32 good enough for getting 'loud' and somewhat low on music? i also plan on firing towards the cabin and sealing it from the rest of the trunk. kind of like this A local shop quoted me ~$250, and they said the enclosure would sound better facing the rear? im not too sure about that one. what do you think? here's a lil…

Hey whats up im doing a build for my ROOM for music haha. I have a sub in my car why not at home. Ok So i bought a RE SR10-D4 10", here are the specs. I want to Make a slot vented box 1.5cf tuned 34 hz. people in the other forums said that the tuning will be too high for my room my room is 12'x9'. what are your views on it? I am going to put 300 rms. Ive built boxes before But i still dont know how to design one on my own so im asking for you guys to help me with the build could someone design a box for me i want the sub to be top mounted with the port on the side. I just need a cut out sheet with the dimensions of the box. billy Specs of the sub * Kraft Pulp Cone * Ruba…

This is the standard enclosure offered with the Icon package. This was built early last week for a customer who already has an Icon I believe.

I am in need of i box. I'm going to purchase 3 kicker CVX 15's and i want a quote on a box I had a guy eyeball me a design and send it to me it's a really good description of what i want im not sure if the specs are correct because he just eyeballed it my car is a 1994 grand marquis and i measured my trunk its 3ft 4in in length also 4ft 9in in length if the design is like the one in the pictures below it's roughly 1ft 11in from bottom of trunk to the top and roughly the same in width from back to front.

Hello, I'm not sure if you remember me but I e-mailed you guys a few weeks ago about a box for two 10w6v2's, well I sold those and will get a 13w6v2, I'm hoping you guys can just build a simple sealed box for me. I sent you guys the 25$ for the design and I am waiting for a reply. What do I do now? I emailed chris(at)fishercustoms(dot)com, just waiting for a reply. Is there anything else I should do? Did I do everything correctly?

This one will be 2.2 cubes @ 32 hz I believe. The customer sent me his own design. Will be finished with medium gray carpet. Pretty straight forward build here...

max dimensions are 36w17h23d... is it possible to have sub back port side or would the traditional sub and port back work better. 15 fully loaded by the way

i was wondering if u can draw me up something with dimensions and all , that would be the perfect ported box for 2 nightshade 15"s?

This is a standard 4 cube sealed box for a pair of 12" (BL's maybe). The customer will be lighting the front with a neon, and wanted a little home for it to direct the light down the front side of the box. It will be left bare, and be color matched to the vehicles interior later on.

Anyone have any ideas how to make my box slant at the top and bottom and port in the middle, box is 21 cu. will that work by the way?

Hi i know this is perhaps a little off topic but was thinking when you use fibreglass or carbon fibre as detailing on a box(around the port area and front pannel) will this stick to the wood or will this cause some nasty rattle or something? if this is possible what would be the trick behind it? thx

Hi FC, Just wondering about getting an enclosure and a cut out sheet for another one from you. I send an email to you from the site a couple days ago and have not heard anything. I know you guys are probably quite busy, I just wanted to make sure that you got my email. Hope it was ok to post this here. If not I am sorry. I would love to get an enclosure done by FC and it would be a tricky task. That is why I am not gonna attemp the big one. Thx Josh~

Hello Mr. Fisher. I was looking at your web site and saw that you had pre made box designs. I was wondering if these designs also included a cut sheet. If not, can one be purchased? I was looking at the 7 ft slot ported box for two 15's. I am planning on using SSA Icons in this enclosure. Thanks. Also what size of wood is supposed to be used for these designs. Thanks for your help.