Direct Sound Solutions

Yeah, that was a pretty bad Topic Title. He he. My bad. Any ways, I took advantage of the DSS deal, picking up a few woofers, and man are my arms tired..... Enough with the bad jokes, here are some pics. I was a little worried about that one box, but everything checked out good. All lined up and ready for action. A couple of motor shots. Not my best work, but still and impressive sight. This will be the first time I run four subs in a single setup. Stay tuned for a build log coming to a forum near you. These subs look great. A+ build quality. All the glue joints look solid with no excess glue. No weak spots were revealed when pushing up from the ba…

I came home to a nice surprise today. I saw Quentin had a lay away plan so I took advantage! Ethos 15. This is so much bigger in person. It needs to be seen in person to really appreciate. Far bigger than I had used previously. Extremely well built. You can see great care was taken on the glue joints and little other details. Nice finishes and large diameter flat wound coil. My son Nico wanted to take it for a spin.

I was wondering how would 4 ethos 15s perform on a crescendo 5500 I'm really stuck inbetween 4 ethos 15s and two zv4 18s

THE EQUIPMENT (6) IA LI 15'S (2) IA 20.1'S (2) DIEHARD PLATINUMS A LITTLE BIT OF 1/0 AMD SOME SPEAKER WIRE EVERYTHING WILL BE WRAPPED IN BLACK CARPET THE BOX THE TRUCK

A custom built 15 from my spare parts rack I am building for a buddy. It's going to be ran in a 4 cubic foot enclosure tune to 34 hertz on a Kicker ZX500.1 in a Chevy Avalanche. As a side note I can do this for other people as well.

I'm think of running some Ethos subs in my truck. I have about 8~ cu ft to play with and an SAZ-3500v2 for power. Would running 4 12s on that amount of power be a waste versus just running 2 15s or would there be anything to gain?

I had a sample of this driver sent along with the Ethos production run. I don't have pics of the actual motor yet. When Nick slows down a bit he will send some to me with some group shots off all the motors I had made. This driver offers 22.5mm xmax per overhang method. It will be ~27mm per the typical 70% BL rating. The entire stoke of the coil is covered in aluminum faraday rings. All the way from the bottom plate up to about 20mm above the top plate. As long as prices stay the same I plan on releasing the Beta version which uses open tooled soft parts for $375 shipped for the 12 inch. RMS rating should be in the 1,000 watt range and enclosure recommendatio…

My new fcebook is "Direct Speaker Supplies." Take a look spead the word.

The 12 as recieved via FedEx from the build house. Each package has the sub's serial number on it. And the model of sub, size, and ohm load. No need to worry about theft during shipping. ALL orders are shipped direct signature. You must sign for it for FedEx to drop it off. On top is the warranty card. This must be filled out and mailed back to me for your THREE YEAR WARRANTY!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Then we have a little wood Foam to keep the sub from shifting plastic bag to keep it nice and pretty box attached to the inside of the packaging to keep motor from shifting. Had an issue with scrat…

I need help creating a product list for Direct Speaker Supplies to carry. I already have just about everything to recone subwoofers on its way. The problem is I have accounts with just about every distributor you can think of and combined they have tens of thousands of parts. So I'd like to know if there is a special item that you would need. Maybe something no one else carries or they do and it's just too expensive. For example maybe you would like to purchase the really nice high nap carpet I use on my enclosures. Give me a list of what you think would be priority, that must have hard to get item. NOTE I WILL NOT BE CARRYING ANY PRODUCT LIKE AMPS OR SPEAKERS (B…

Just excited to keep info following for the updates onbthe Ethos 18's

Final MAP pricing Ethos 12 $345 with free shipping to continental U.S. Ethos 15 $355 with free shipping to continental U.S. Preorder Sale terms of sale: Sale will begin on Monday July 22, 2013 at 12:01 a.m. central standard time and will end August 11, 2013 at 11:59 p.m. Product purchased during the sale will be refundable up until the closing of the sale MINUS 10 PERCENT of sale price to cover paypal fees that I will incure. Product is expected to start shipping to customers on the week of August 12, 2013 however like all sales this is an estimate and can vary. Pre order Product will NOT be ref…

I have modeled several enclosures below the show the difference between large signal and small signal T/S parameters. To gather large signal parameters we use what klippel calls LSI (Large Signal Identification). The following is Klippel's definition of LSI: LSI modules measures the linear, nonlinear and thermal parameters of transducers operated in free air or in a sealed or vented enclosure. The transducer is operated under normal working conditions (vertical position and fixed clamped in a laser stand or enclosure). Starting in the small-signal domain the amplitude is gradually increased up to limits admissible for the particular transducer. The maximal amplitude …

The below are the Large Signal Parameters tested per a klippel analyzer performed by Patrick Turnmire with Redrock Acoustics. For those who do not know what large signal parameters are, they are Thiele Small Parameters of the driver with a large enough signal to excite the cone to normal operating conditions. These are used instead of typical small T/S parameters because they more accurately represent the driver. When the driver is under power at large excursions the parameters can shift a great deal making small signal parameters not an accurate representation of the true nature of the transducer. Later when I get time I will also post small signal parameters to comp…

As the title says I am looking for competitors to do R&D on a large SPL driver. For testing purposes only one driver will be available in either a 12, 15, or 18. This is a very large driver weighing about 105 pounds. Below is a comparison picture of the driver's coil next to a Ethos and FI BTL N3 coil. The coil is 95mm long 3 inch 8 layer dual one ohm coil with an Re of .9 ohms per coil. The coil produces a BL of 51.5 and a motor force factor of 1,484. I am looking for a seasoned competitor with a few years experience preferably someone that has attended nationals a few times. If you are interested send me a PM with your info.

This label will be attached to the outside of the shipping packaging for product identification

The below warranty card will come with all product and will activate the three year warranty that will be available on all DSS product. I still have to set up a P.O. box, but mailing info will be added to the card before product starts to ship to customers. REAR OF CARD

I will be offering a three year warranty on DSS drivers and I need a way to track them so a sticker with a serial number will be placed in the rebate on the rear of the motors to hide the tool mark from being turned on the lathe. The below logos are what I have been working on (be gentle it's my first time using Corel). Which one do y'all prefer? The blue will be a royal blue and the white will be brushed aluminum.

left to right: Magnetar (HUGE 270mm MMAG), Ethos, Fi BTL N3 coil Fi BTL N3 on left, Magnetar on right Magnetar coil: 76.657mm ID, ~92mm OD, 95mm winding hieght, dual thickness aluminum coil former, 15 gauge aluminum magnet wire

Got a few samples today of some material we plan on testing to see if it offers any advantages in heat transfer in motors, and if it has any value as a faraday ring. The silver pieces are aluminum and the copper colored is copper.

Future products will have the option to monitor coil temperature in real time. This may be a desirable feature for people in comps running tons of power. Temperature sensing will be done with a tyke K thermocouple imbedded into the topplate a couple millimeters away from the coil. This can be used with any Type K thermometer.

since all the kiddies like videos, here is the Ethos 15 on ~1,750 watts. Mind the jerry rigged set up. I don't currently have a large enough battery supply in my shop to run my power convertor on a large amount of power.

All parts for the Ethos have been ordered and I'm expecting them to be in around 3 months. ETA will depend on if all of the parts leave China before Chinese New Year. So to be on the safe side I expect them to be in Mid to late March. For this order only 12 inch and 15 inch drivers will be available. Terms of presale are as follows. -prices are shipped to the lower 48 12 driver dual one and dual two $300 15 driver dual one and dual two $310 -preorder sales are refundable. I have already paid for the parts and they have been ordered. This presale is to only gauge interest not to use your money to purchase the parts. Any returns will be subject to a $25 refund fe…

A production motor was air mailed to me so I coned it to a 15 and will be breaking it in over the next week to send out for klippel testing and power confirmation. I tested it with a DATS system and got some crazy numbers that just aren't physically possible so after it's broke in I'll just do the measurements by hand. I'm happy with it however the chrome is not as dark as I was expecting (I wanted black chrome) but it's much more durable than the black epoxy paint that was on the original sample. The below pics are a 15 and it weighs 61 pounds for those of you planning on 8 of these in a Scion. No cone shots as I just used plain dust caps. My custom tooled caps won…

I need some help building some door panels. The panels are from a 96 2 door Tahoe and will house 4-6.5's. I'd also like to put 3 tweets in the A pillars. I'm in the Hammond area. Please email contact info to "[email protected]" - Thanks - Jared