cheese20323

Done?

The fat and the furious.

Sell it locally and try again is your best bet.

Try bringing down your seats and slide it through the back.

I'm 15 too. and have 2 12 RE SE's on a US Amps XT4000DE and Re Components(Thanks Stevemead) But in order to make money I mow some lawns and I live in a farm type neighborhood and I clean up horse shit and I get a pretty big ammount of money by doing this.

The us amps xt1600.4 is good or try one of the merlin series.

amps are louder if you leave the smoke in them......................lol....

As soon As I drop 800 dollars on the dash kit and HU.. My dashkit is around 200$ and I have to get an 80$ Wiring harness why don't you use your mad F/B skills and make one...

16ga for speakers and 12ga for subs...30 Ft should be more than sufficient.

my HU has rear, front, and sub outputs. so since the kit comes with one set of RCAs... i just need to buy one more right? also, i should go ahead and buy more speaker wire right? the kit comes with 12ga . so just get more of that? also, can i use 12ga for my subs when i get them in?...i think ill get like 30 ft. just to be safe. Yeah jus buy one more set..then keep the 12g for subs but with another amp kit it will be fine...But get 16g for speakers 12g is a bit too thick and isn't necessary.

yes you would need the 4 channel RCA's...and Y splitters if your deck don't have 3 outputs.

I say leave the speakers(rears) run them off the other 2 chans and you will definitely be able to hear them....You will notice the difference without the rear speakers when your cruising with the sub low.

TRUTH ! But even projectors can blind people if they aren't aimed right. Exactly, brother! Normally if someone is going to spend extra and get the projectors too I hope they plan on aiming them 90% of people don't work logically Mind you, after I upgraded my wiring it was clear that the right headlight was aimed like shit... The worst ones are whe one light is brighter than the other.

1.4 is 2 ohms....

When you say grounded you rca's, did you solder a wire to one and ground that to the chassis? Different way? Banging, did you ground your HU to the factory ground wire. If so you may want to run a longer length of wire and make a new chassis ground. no. my HU was poorly grounded inernally and got some wire and wrapped on outputs then put it on a bolt on the HU. Got ya. Pioneer? you guessed it! Yeah found it was common on them...

When you say grounded you rca's, did you solder a wire to one and ground that to the chassis? Different way? Banging, did you ground your HU to the factory ground wire. If so you may want to run a longer length of wire and make a new chassis ground. no. my HU was poorly grounded inernally and got some wire and wrapped on outputs then put it on a bolt on the HU.

Pretty much.never ne it was oughts..i just say one oh.

bad ground somewhere.....I grounded my RCA's and humming went away....but I only had the pop occasionally.

Kicker wire is nice but pricey.

Obviously you need to state a sub. The US Amps ones are fine many of my relatives are running them no problems at all.

whats the RMS wattage your shootin for?

I have the older V2 model and have yet to have a problem pushing to 12 SE's to their limits never gets warm and is on a 1 ohm load. My brother has the original XT series and he has not have had a problem from a 3 year old amp either so I do expect a good pic. I can get a picture of the board if you want.

Fi NL 15's SA nightshades

I'd say different shaped bolts holding down your equipment my amp has a star shape then a square then a flathead then a cross

Well I would rather run a more current driver than any DC sub.