Dangrebel

I went with an 80prs if anyone wants to know lol

I want 2 caps right now!!!! Hurry and work out the details!

I've had an abscess and I thought it was my lymph node. It swole up big lol. Hope it's nothing serious!

Ok well you can always run like a rebadged battery like a diehard platinum or dura last platinum. They are cheap and good.

Definitely amazing goop

What kind of suv?

Same here! I drive a long bed truck and do fine with a wall. always slowly back up in parking lots though. Almost ran a lady over because she stopped behind my truck with my reverse lights on and was texting lol

4 jl audio 12's on a 300 watt amp

1750 wattttttttttttsssss

Sold! To me!

Recieved an incriminator death penalty with that much and I still had about 4 big chips on the magnets.

Awesome. Looks loud in that cab! What amp is it on?

I believe the lms-r is a big brother of the rlp. I've heard they get stupid low

I want a few RL-P 18's for my house. That'd be nice.

I reflect off my windshield for a greater stage depth. It works for me...

I'm sorry, but they are the worst tool for measuring. This is exactly what I am talking about in the previous posts. You see it acting differently and pick arbitrary numbers out of the air , insert, and bam. See what I'm getting at? Isn't that how you measure all the time. You measure with your eyes when you need to stop your car so you don't wreck. How far to step so you don't fall down the stairs. What size a bolt is so you can get the right size wrench. I don't carry a fucking ruler in my back pocket nor do I care too. See what I'm getting at? I noticed a very audible difference as well. At full tilt my truck is quiet as shit on the outside with the windows up. The problem is your eye is not sensitive enough to he used as a measuring device for panel movement. It's akin to stating you could measure a driver's excursion by eye. Audible differences are a given, but you are already perceiving a change so you brain has already signaled there will be a change whether there is or not. I cannot measure exact sizes with my eye but, I can tell you what's its close to. I can tell how much my subs move. Just watch the letters. Same goes for my spotted up roof lol. Everyone that's got in it after the deadener has been impressed too. It does a good job for what I paid for it. Was I willing to spend 3x as much on sds? No I was going the cheaper route and it worked.

I'm sorry, but they are the worst tool for measuring. This is exactly what I am talking about in the previous posts. You see it acting differently and pick arbitrary numbers out of the air , insert, and bam. See what I'm getting at? Isn't that how you measure all the time. You measure with your eyes when you need to stop your car so you don't wreck. How far to step so you don't fall down the stairs. What size a bolt is so you can get the right size wrench. I don't carry a fucking ruler in my back pocket nor do I care too. See what I'm getting at? I noticed a very audible difference as well. At full tilt my truck is quiet as shit on the outside with the windows up.

Eyes...

I've used the 80 mil b stock. It worked fucking wonders. My roof rattled so bad. It actually was louder than the bass. Now after about 60 percent coverage on the roof, it has not rattled one bit. The roof on my trucks moves like a couple millimeters versus the inch and half like it used too.

Either running hids so they don't dim or, running a good batt in the back helps tremendously.

Ok. I've encountered the same whine on my small case gm alt. second. The alts will be on all times. The only time one of your alts will be off is when the other one is outputting a higher voltage. it will only excite the other alt when voltage drops lower than the output voltage of the turned off alt. I daily drive with a dual alt set up. When my 2nd alt comes on, it whines. My primary is a 270 amp mechman. The small case is my secondary which is off until I demo or pull a heavy load on the 270

And that's why crescendo is the shit lol!

Why did you go with a 1500rms driver and now complaining about the power handling?

They are 1500rms a piece...

Damn!!! I'm tuned at 29hz and it dominated my truck lol!!! Shits nice, let's hear some more