sundownz

Free shipping added on the Nightshade in continental USA!

Come on now, guys! Am I going to be in Indianapolis all by myself? *laughs* Someone will be there with my stuff so I'm likely going there

0.5 or so should be good to go mechanically.

This is an option I only suggest that much power in tiny enclosures as the woofer doesn't really need tons of juice to get moving!

Gotta follow demand No worries... I'm still developing amps as well, but I need sub lines to satisfy my dealers.

Sure will You can run them to a 4 ohm load on your 100.2 no problem. Like I said, they are just as efficient as the original SD-1 (actually 0.1 dB higher on sensitivity) -- but they have the potential for more thermal power handling and more x-max.

Sure did It will move a surprising amount for a 4.5" deep speaker! The primary target market for this woofer is under-seat or behind-seat truck enclosures, especially for those who still want a great sounding woofer for this application. The 4-spoke cast basket allowed me to make this woofer even shallower than the original SD-1 AND increase linear excursion capabilities. The same narrow profile surround from the original SD-1 was utilized to avoid "smacking" the floor of the truck, or the bottom of the seat (depending on orientation) -- it still allows substantial travel beyond the actual linear capabilities of the motor. The two prototypes will quite likely go directly to a customer through one of my dealers... at which point a good 3rd party review will be available on the protos to see if I met all of my goals!

The SD-1 v.2 protos are in... they take everything the SD-1 was good at and take it up a notch. 1) They are even shallower at only 4.5" mounting depth (10" model). 2) They have more linear x-max. 3) They have a 2.5" voice coil so they will handle twice as much power thermally. 4) They maintain the efficiency of the original SD-1. 5) They maintain the small box requirements of the original SD-1. 6) They maintain the low-end performance of the original SD-1. 7) They are now DVC 4 ohm for more wiring options. 8) They now have a rubber mounting gasket. These subs will throw down in very small enclosures and will now handle much more power. Ideal for shallow truck enclosures! They utilize a single 6" diameter magnet slug to achieve the necessary flux. Behind the cone you will find a progressive roll spider and a special treatment applied to the back of surround and upper lip of the cone to get more stability from the surround and to bring the Mms to where it needed to be. The leads are offset out to the sides and slightly raised to eliminate the possibility for slapping and the motor itself has quite a bit of clearance for the coil due to a deeply bumped back plate. My apology for the low quality photos... I recently broke my digital camera and have not yet replaced it: MSRP will be around $229 - 249 (pending finalized build costs) for this USA built subwoofer. When they are available contact your favorite dealer for best pricing!

Thread cleaned up... Re-Coned 15" SI Mag added.

You'll be good, especially running the 3000D @ 2 ohms.

There are still SD-1s in stock, any more love for them?

http://www.soundsolutionsaudio.com/forum/i...showtopic=11327 Post #9 in this thread seems to indicate that you would like the 1000D. You do have a few benefits outside of any sound benefits... as you said before, you can contact me if you want I have extremely fast warranty service, I will replace the amp in about 90% of cases so you have a new unit coming back to you quickly. You can strap the 1000Ds if you want another one later.

Glad to see you got it

Ross, Did you give them the right address? If so... I shipped an amp that was stolen from in front of an apartment. UPS covered it under insurance.

Corey, If you can even begin to say that the 9500 sounds good then, yes, this sounds about as good as the 9500

Scott can make you an 18" assembly for the XXX. I have four of them on the way to me now, actually

One Refurbished SAZ-1500D added to the list.

First... *laughs* The new DP... like Bigfoot... except less pictures are out Can't wait to see em, Nick.

Awesome results!

Shoot me an e-mail to [email protected] e-mail sent i currently have 23 1st place trophys this wekend as i did not have my power plant i went to compete with 200watts per sub got a 144.6db @ 55Hz box is ported to 45Hz Have not seen it yet... lost in limbo.

Shoot me an e-mail to [email protected]

Full power testing on the 1500D is sticky @ the top -- for regular voltage and 16+ volt systems. Check those posts out. If you are a consumer than you need to contact a dealer for pricing, Aaron @ SSA would be a good one to try If you are an SPL competitor with a verifiable history and solid plans for the season then you may be qualified to buy from me directly. If you feel that you may be qualified contact me at [email protected] and we can talk. I generally just swap out a new amp for warranty I'm sure someone around here can vouch for that for me. I don't have alot of warranty work to begin with, though, but in general I send a new unit and I worry about fixing the old one and re-selling it as refurbished.

Ouch man! A pair of 1500Ds would do nicely @ 2.3 ohms strapped

Sweet car and system

*laughs* I would too!