duece212

This blown woofer is good data for you, now you know what is too far on the gain. My way has always been turn up the gain until something smells funny, sounds funny, or breaks...then turn it down a bit. Get a recone and turn it down a bit

Nice! I'll shoot you the balance in paypal when I get offa work tonight

I went cheap on amp. MB Quart 1500.1, the discus amp

Looks great! That carpet should match the rest of my interior nicely. I suppose this means I should get off my butt and run some power wire and start finishing things up so I can give the new box and xcon a listen. Can't wait to see how the xcon does sealed.

Lookin good, all my measurements told me an xcon motor will fit in there....its going to be a tight fit

Very cool! I want one

Sounds good man, pm me your paypal address. Since it won't start till the 24th I might play around a bit and put a brace in for the port since my truck rides insanely rough it might need it. I might through two dowels in the design front to back as well. Whatever it ends up being to add those if you can just tack that onto the shipping I can take care of that when its done.

Ok, here are the final plans with the .75" side indents included. Let me know if any of the measurements are hard to see/understand. I've got the centers marked for the sub and port cutouts. Sub cutouts at 7.25" and 4" aero cutout at 6.25". I believe those should be right. No wire terminals on this one please. You can either shoot me a paypal invoice to my forum name @ yahoo.com or pm me your paypal ID and I'll shoot some cash. Thanks!

Well I think I got stuff situated to where it will barely fit. Not much room between the aero and the woofers but as long as the flare on a 4" aero isn't over an inch from flare to where it necks down to 4" tube I should be fine. Need to know how much you inset the sides though so I can account for that. Here is the new plan, once I get your inset specs I'll get you the final measurements and some paypal money, thanks:

Sounds good, after triple checking I'm changing the dimensions just a bit to make sure I can have my seat pushed back with no problems. Was thinking: 28w x 16.5h x 13 bottom depth x 6 top depth With those measurements its getting tight with trying to cram a full size 4" aero and two sa8's in though. Mockin it up in sketchup now to see if that's even going to be possible. If you have other suggestions let me know

Its for the back of a 09 Ram 2500 single cab. Pic below of what I've come up with. My sketchup skills suck unfortunately. Just a single 3/4 baffle and a single full length 4" aero. Subs forward, port to the drivers side (its on the wrong side in my crappy sketchup image.) If my math is right, counting .1 of displacement for each woofer I should be close to 1.5 net at 35hz: 26.5w x 17h x 13.5 bd x 6 td Let me know if you have any better ideas, or if not what you need for the below box in gray carpet shipped to 80634. Thanks!

Got my order for two in, just wanted to say thanks Jacob. It's been said many times before but worth saying again...damn good dood to deal with.

Thanks for the quick reply, money sent for 2. Going in the back of my single cab 09 ram. For somebody who listens to mostly rock, very little rap, and doesn't really care about the really low stuff what do you recommend. Small box would be helpful, available power won't be an issue.

Jacob, dropped you an email to see if you have any left. Looking for 2, would prefer dual 4's but can make dual 2's work as well if that's all you got.

No updates yet. Its been below zero or in single digits since I got home. Today was the first day in the 20's for quite awhile. Since the truck doesn't fit in the garage it only gets worked on when its halfway warm outside :/ I need to pick up some more wire too, but will probably be waiting until after christmas to do that. I want to make sure I don't break the bank buying christmas presents before I spend more on myself.