hondakilla98

1.5cf PER 15 ? That is TINY...IMHO go for double that. Efficiency is your friend. Do you need to worry about efficiency when your giving subs 4x rated power? I don't think so.

I see m5 hasn't been here yet. So I'll say it for him. 4-12's on 6k isn't SQ. If you really want SQ focus on your front stage. But if you want loud and clean I'd go with the 4 ported over the 6 sealed.

i got some sketches of what my box will look like. Here you go. He's starting it today. I got my sa-10's last week. Now all i need to order, is my deka 9a31.

Funky Pup!!!!!

Hey alex01 how did you get the box in the trunk? I have a 95 eldo and I'm wondering if there are any tricks to getting a big box in the trunk.

Damn alternator went out yesterday. And I'm still waiting on parts. Hopefully I'll get my parts Tuesday and then fix the ac, rebuild the alternator to 240 amp, and do the big three. Good news is I found a local box builder with good prices. I'm going to meet him today to plan out the box. And hopefully have the box next week. And my sa-10s are supposed to be here on the 2nd.

i just wish the sa-10 had the 12 spoke basket. Of course then I'd have to mount mine inverted, so I could look at them all the time.

Well it says car quest on the battery, so I'd assume its a rebadged deka. Like the Oreilly's rebadged deka. I definitely wasn't expecting to see the same kind of car I drive, when I opened the window. Nice, Now I'm wondering if I still want to face my subs and port back with my 2 sa-10 build.

Nice install, and a great looking box. Well here's a general guideline from jacob on the 8's. 1.25 cubic feet = 300 watts 1.00 cubic feet = 400 watts 0.80 cubic feet = ~450-500 watts 0.60 cubic feet = ~500-600 watts So 8-8's in 6.5 cu ft on 2 1500d's would be a great match. And maybe still fit under your window line.

Canopy looks great. But I'm not too sure about the brush guard.

well I'll definitely post up a review when it's all installed. I'm excited. It's been 2 months since I had a system. I'm using the stock tape deck with an adapter to my iPod for now. My friend had two type r 10's in a ported box in his car running off 900 watts. It was pretty loud, so I'm looking forward to blowing him away with my two sa10's on 1600 watts. Not to mention he had infinity reference coaxials in the doors for mids.

Mb Quart DSC4125. It's 4x125@4 ohm, so I'm thinking I'll have about 4x65@8. Which with the higher sensitivity of the 8 ohm drivers should be fine. And if not, then I'll have to buy another one and bridge them. Talk about headroom. I ordered an a/c compressor kit and new condensor today. Hopefully all my a/c parts and my high output alternator rebuild kit will get here this weekend and I can finally have A/C. Good thing it hasn't gotten hot yet here in Oregon.

That's great news. Looks like I got in just in time.

I took some pics of what i have so far for equipment. My mids, tweets, and rca's showed up today, and my tweets weigh as much as my old mids. Here you go.

I ordered a 240 amp alternator rebuild and smaller pulley from springhill today. I think I'll be waiting on the Deka battery for a while. I have an hc800 I'll use as a temp. Now it's time to fix the ac. My compressor is toast, so time to order one of those as well. I figure I'll do the ac compressor and alternator at the same time.

My friend has the ixa-w404 in his civic and loves it. I have an ixa-w407 i'm waiting to install. My last deck was a cda-9886 and i never used the cd player. Also if your worried about preout voltage. Get the pxa-h100 and use it with any of the high end alpine media decks. It gives you 4v preouts and the ability to run active, and autotune using imprint if you want.

I'm gonna be running two of these in 2.5 cu ft ported, tuned to 30hz. How much port area should I run with these? The box I have modeled now has 31 sq in, or 12.5 per cu ft. I'll be running these at 1 ohm off my SAZ-1500D.

Nice build. I'm just wondering how your gonna hear your mids with them firing at the side of your seat?

You should check sq_mgb's build log. He also has a regular cab truck with a console box. Here's the link. SQ_MGB's 2002 Chevy Reg cab build - SSA Car Audio Forum

Ordered 3-2 channel knukonceptz klarity RCA cables and a roll of 16 gauge speaker wire off eBay. Hopefully next weekend I can pull out my interior and run my rca's, speaker wires, and power wire. And start on my a pillar pods to mount my hds tweets. And while I'm under the carpet I'll put down some deadener.

Here's what I'm thinking.There will be a removable cover in front of the battery. And maybe one on top of the box. So when you open the trunk all you'll see is a carpeted box with two subs and a port. With the battery cover. Everyting black is carpeted. With a cover in front of the amps as well. everything black is carpeted.

I finally made up my mind on my subs and front stage. I just ordered 2 sundown sa-10's to run ported, tuned to 30hz in 2.5 cu ft net with 33 sq in of port area. And I bought peerless Nomex 830875 for my mids and Scan-Speak Discovery D2608/9130 hds for my tweets. Here are links to the mids and subs if anyone wants to check them out. Peerless Nomex 830875 Peerless Nomex 830875 - 6.5" Nomex Cone Woofer from Madisound Scan-Speak Discovery D2608/9130 hds Scan-Speak Discovery D2608/9130 1" Textile Dome HDS Tweeter from Madisound Sundown SA-10 Sundown SA-10 Pre-Sale - SSA Car Audio Forum I still need a second battery, Hi output alternator rebuild kit, rca's, a roll of 16 gauge speaker wire, and a sheet of mdf to build my box. I'm going to put the subs in the front of the trunk firing towards the back of the car. I have 38w, 18h, and 23d to work with for space. The box will be 29w, 14h, and 19d. With a group 31 battery mounted next to it and both of my amps mounted on top.

Paypal sent for 2 d4 subs.