Welcome to SSA Car Audio Forum

Register now to gain access to all of our features. Once registered and logged in, you will be able to contribute to this site by submitting your own content or replying to existing content. You'll be able to customize your profile, receive reputation points as a reward for submitting content, while also communicating with other members via your own private inbox, plus much more! This message will be removed once you have signed in.

audiohz

Members
  • Content count

    67
  • Joined

  • Last visited

Community Reputation

2 Neutral

About audiohz

  • Rank
    Newbie

Profile Information

  • Gender Male
  • Location hickory

Recent Profile Visitors

1,161 profile views
  1. So would that put it at -6db at 24?
  2. Just curious honestly which one they use I have read that the Butterworth filter can also go up to 24dB slope, I thought in the past the highest it went was 12db slope.
  3. On the scv and saz amps what style crossover is used butterworth or linkwitz-riley ? Have never seen it said on sundowns specs.
  4. On the scv and saz amps what style crossover is used butterworth or linkwitz-riley ? Have never seen it said on sundowns specs.
  5. On the scv and saz amps what style crossover is used butterworth or linkwitz-riley ? Have never seen it said on sundowns specs.
  6. On the scv and saz amps what style crossover is used butterworth or linkwitz-riley ? Have never seen it said on sundowns specs.
  7. The amp is 150 rms per channel so it's not crazy over power when rms is 100 rms per side on the sundowns. The real question now is should I ditch the kappas and just run the sundowns. If the kappas truly a 2 or 3 ohm speaker like they state wouldn't it be robbing power from the sundowns being a 4 ohm load?
  8. No the math is not difficult, with the kappa saying it's a 2ohm load mixed with the sundown that's a 4 ohm load I would have a mixed ohm load. Power across that would be less to the sundown. On my dmm the kappa is showing me a 3ohm load though. But with the kappa wired in and the sundown components on each channel with the dmm I'm getting a 5ohm load! With each channel wired in parallel shouldn't my load be lower then 5ohm?
  9. Installed a self exciting high output alternator worked fine once installed but once the car sits over night if the temperature drops below 30 degrees the next morning when I start the car I'm not charging, voltage is at 12.3 I have rev up to 3k still it takes probably 20 seconds or more before my voltage goes up to 15.1... on warm days and nights never an issue. .what could be causing this?
  10. I have the sa6.5cs v2 and a set of infinity kappa tweeters all running on the rockford p300x2. Should that be enough power?
  11. I'm not trying to push more from them, I haven't installed them yet. My amp is a Rockford p300x2.
  12. I have seen where jacob has said the test is full range down to 20hz on 100 watts RMS and will handle much more with crossover setting on the low end.. So say I set my hpf at 100hz 12db slope should I be OK with 150 watts RMS per side them I would think so.
  13. With the sa 6.5 components how much rms can they take?
  14. I have a yellow top under the hood with the big 3 done in stinger 1/0 an a run of stinger 1/0 to the rear batts. One is a kinetik hc 1400 to a hc 1200 so 2600 total. Wired to two kicker zx1000.1 my question is the one single run of stinger 1/0 to the rear OK? It's ofc .
  15. my co worker has a cc1. He telling me to set it at 28hz but that sounds to low.. I'm putting 750 rms on the sub also.