SPL & SQ / Fabrication

I've been trying to find a 12 that would give me the best output for my 350z....so obviously I don't have a ton of space but I'm thinking 2.5 cubes before displacement. I don't know a lot about this stuff so I thought I would come on here and ask. I was either thinking a xcon or a sundown Z maybe or soundqubed to save some money. Any opinions on what I should do would be great. I forgot to mention that the amp is a older nine.1 which is about 1500 rms at 1ohm.

Hey all.I was wondering if my port is to close to my rear hatch.My friends and I both seem to think my system should be louder and I seem to think that it might be my port being to close to my rear hatch and not having enough room to breathe.My system consists of a DC 5k and 4 10" DC lvl 3 m2 subs with the level 4 upgrades.My enclosure was made by DC Creations and is 4.5 cubes after displacments (I believe) and tuned to 33hz.Here is a pic of what im talking about with the port.I can take a better pic if need be.So what im wondering is if I flip the box around with the port facing into the cabin instead of towards the hatch,would it help out any or would a enclosure with s…

So here is the story. I finally have all of the stuff I need to install my saz2500d. Took box out, 4.75^3. Big for my s-10 3 door. Basically an extended cab with a door. Have the zcon's ready to drop in. Put empty box back in to see where I could put my amp and this is where I run into a problem. Box goes from floor to 2" below back window. From driver side door to 5-6" from other side. With subs installed there is 12" of room on top of box. Amp would hang over about 5" or so. The port is on the passenger bottom. If I mount it on the box overhanging the open port side, would that be a problem? What about mounting it inside the box? The port is 20" wide and 24" long. Plent…

Ok I was looking at my trunk and if I want to make a 8 cubic foot box the only way I am going to be able to do it is make an odd shaped box ported, or do aeroports. I am just wondering how I would tune a 8 cubic foot box after displacement for 32 hz with aeroports. I am kinda new to these and I was looking at info on how to use them and I am just majorly confused.

Vehicle : 2003 VW Passat Location in the vehicle: Trunk Space available (Length x Width x Height): w1- 39, w2-42, h1-15.5, h2-19.5, d-25 Subwoofer make and model: Custom, similiar to the Sundown X but more motor force, excursion and lower fs Subwoofer Size:12 Number of Subwoofers:2 Type of Port (Kerfed, Slot, Aero, etc.): Up for suggestions but thinking about aero to save space What type of music do you like?: Chopped and screwed, decafs low stuff (about 18-35hz) Is your goal SPL or Everyday Music?: Everyday Tuning Freq (Hz): To be determined - probably around 26 Volume : 5-7 cubes depending on tuning, port and bracing. Questions: I want to first start out saying I blew m…

Can someone check my work, to verify I am gaining maximum beneficial value from the bracing? From my understanding the bracing has two primary functions, other than structural support. To keep two panels from having the same resonate frequency, and to break up standing waves. Is there any adjustments I should make? Will I benefit from routeing the bracing edges round? Should I add a few randomly placed triangle braces? Remove the diagonals from the center brace? This is my first enclosure with matrix bracing, so I could have a big red flag in there and wouldn't know it. The enclosure is built for two SSA 15" Icons sealed, running 2000 watts total. The final …

I will be installing a budget audio system in my 2008 Hyundai Elantra four door. I will be running a three way front stage. I am using Viper Audio 650.2 passive component set. They are metal dome tweeters with 6.5" midrange and crossovers. The tweets are harsh and the 6.5's lack midbass. I picked them up bnib cheap.... I will be using a Boss REV-665 four channel for power. Again got the amp cheap..... Channel 1&2 for the component set and channel 3&4 for 6.5" woofers. Mounting: tweeters in A-pillars aimed at each other, 6.5's midrange in custom kick panels aimed at dome light, 6.5 woofer in bottom of front doors mounted behind factory door panels and aimed at each…

I need a ported sub box to around 33 Hz for an xcon .. I have 12.5 H x 32 W x 14 D to work with. I have a metal brace on the floor of my car that I need to work around. I've hit up ram design and he said he was to busy at the time , Dave the box guy never replied back .. and all the audio shop stores I go to say they can build it but the lowest tuning they can do is 60 Hz wich is bullshit. any help is greatly appreciated

So Ive got what looked like a decent box on paper (BBP6) but once built is quite depressing and seems to be choking the sub. It sounds decent but just leaves the thought that so much more could be gotten from it, but Im not all that great with designing boxes, every now and then a good one pops up. Another member gave me the idea to build the box in a way that the sub would angle some to fire more towards the rear glass and have the port fire back, if anyone is willing to toss in some input or maybe help with a design that would be greatly appreciated. Space to work with is 17.5" tall, 24" deep, and if possible 28" wide but could get up to 36" wide if I relocate the spare…

here we go Here you go. more to come Later

So, i am HOPING this is the final box design for my SPL-15 as I am going ot buy some MDF here in a couple hours. HOWEVER i just thought since this is my very first box design done by myself I would throw it up here for you'all to check out and let me know what you think. Nothing Fancy, just a simple ported box....

Me and smokedog will be hosting a show in bluefield wv at an autozone. We will have it at the end of sept. To space it out from the other shows thats happening up here so we dont get burnt out on it. Spl will have 5 classes still and we are gonna do sq as well. Door prizes will be supplied by Autozone, it should be a blast. But spl and sq will be happening at this show.

Currently I have four Kicker Comp 15s doing a pretty good #, really pounding for a street beater on such a low budget. In the vehicle, we have room for a 4th Order Bandpass. I used a calculator from www.carstereo.com to design one but doubt its accuracy. Can anyone aid me in designing a 4th order bandpass, or link me to a site with theory/equations for one? Simple calculators are hard to trust w/o knowing the math behind them!!

went to a db drag tonite and i took first place. super street 1-2. hit a 143.9 legal on the new TL

Ok well I'm building my new box for one SA-12 it's gonna be 2.48 cu. before port and sub displacement.I'm gonna use one 4" aeroport.It's gonna be sub back port side going in a trunk car tell me what ya'll think?

I'm adding a budget sub stage to my girlfriends 99 Chevy Blazer. It will be 2 powerbass PS-12's on a 600 watt el cheapo amp. Her main choices of music are mainly alternative rock (Matchbox Twenty, Weezer, Audioslave, etc), and country. My question is, what would be the optimal enclosure for this listening style? Would sealed be best for this setup, or a slightly high tuned ported one? (If so, what frequency?) The goals of this system is not necessarily major output, but mainly just adding a good sounding blended sub stage. She doesn't need it to be super loud, but she does want some decent output to be there when she wants it. I will be installing a bass knob for her so s…

I am going to my 2nd comp. this weekend---state finals of WV---I will be competing in the Stock SQ class and I am nervous hoping I do well---I think I have tuned my car so much it is starting to sound unnatural---I need to leave well enough alone but if anyone here knows me knows I can't leave anything as is.----sorry I had to rant alittle.

Okay, Elderado told me that in my car, i have a gas tank between the trunk and the back seat. I actually think that the tank wall is my trunk wall. Anyways, Odds are good that I cant get wire back through any cracks there.. So, where do I put it? <pics tomorrow when its daylight> So, I was thinking maybe right behind the drivers seat in a nice sealed box with some plexy glass over the top so it doesnt get stepped on. Either that *not behind the passenger seat becaues its always moved* or I can stick it in the rear deck. Like, I could be able to drop it inbetween the two rear speakers? But I would need to check the space between the deck and the gas tank. Als find ou…

Topic says is.. I'm still running a Fi ssd 15 and a Sundown sae-1200d.. I know I'm not giving a lot of detail here, but should this setup hit the lows like in the song " White Girl " ? If so do I need a new box tuned to a lower hz?

Want to learn how to fiberglass? check this tutorial out, he knows what he is doing. http://www.automotiveforums.com/vbulletin/...ad.php?t=416484

whaaaaaat. The wires in the terminals are a little cleaner now, had to adjust them some. But they are bad ass custom brass terminals. no ring terminals! see ya at finals...

as topic states, who is going? competing or spectating? Me, competing in 601+mod, gonna get my butt handed to me but its all good.

ok i built a box the length is 31 inch's with is 21 inch's hight is 17 inch's now i have 1 port comming off each side of of the outer 31 inch walls they are 3by21by22 one port on each side of the outer walls of the 31 inch's iam trying to find what cubic feet i have and what is my box tuned at on hurtz ?? any help would be verry helpfull i dident no i could get so stressed on a speaker box!18 fi btl iswhat i have

Ok,so far a lot of testing and tweaking I cannot get my 187s to sound right or get nearly as loud as two 15s should. So I am doing a swap out, I have narrowed it down to 2-3 subs. The Fi BL d1 12, the DC sound labs level 3 D1 or this is a huge "maybe" I was recommended to try the lanzar opti drive 12..........? just trying to get some feedback and if anyone has personally used/tested any of these subs going to run it off my AQ 1200d

hey guys, im going to attempt to build the box for this zcon but i cant draw if my life depended on it. so if i get the max dimensions up on here, can someone sketch me one up right quick? 4.5cubes tuned@ 34 would be nice. let me know if anyone can help me out! Thanks