SPL & SQ / Fabrication

Not so good with building these kind of boxes never seem to e the dims right. any ideas or designs that have actually worked. so lets here some ideas or formulas"

I have the Morel Dotech Ovation 6 two way set and was wondering if I could still use them to go three way sometime next year. I actually was thinking of using the Selenium 6 inch midwoofers as midrange or should I just get another midrange for this? I actually was told to use the Morel midrange but some say go with Hertz Audio midrange. What you folks think and I am going active with this in the future. Thank you.

Ok, I tried to do some research about tuning and port area, so I didn't have to make a thread. I read a thread on smd and they were saying 10sqin per cube was better for low tuning and then others were saying other things like more the better so I don't know which is right. A lot of misleading information out there!! Much rather ask here and know I'm getting the right answer lol I'm most likely going to be ask pro-rabbit for a design once I am sure of my measurements,It'd be nice to know exactly what it should be, so I can expand my knowledge. I would like to know for my system specifically, but also in general. EQUIPMENT: Subs: 2 SSA Zcon 12s Amp: 2 Crescendo BC2000s(won…

ok so i built a box for my new nightshade 18. it is just under 5 cubic feet before sub displacement but after port displacement. it is tuned to 31 hz b4 the sub. it sounds great. my question is if the port area is too small. the re calculator that i used said that the square port area was 55.5. idk if this means inches or what but im guessing inches. the sub performs great at higher frequencies but the lows are kinda lacking compared to the 18" fi q that i had before. any info would be great. also if somebody would be willing to design me an optimal box that would be great too. my dimensions are 36" wide 22" tall and 20" deep. sub and port would have to be facing up. i li…

I'm in the process of designing an enclosure for my Fi BTL UFO 12. I've drawn up two different designs with the only difference being the way the port is constructed. I've seen it done both ways, but I am unsure which would be most beneficial in my situation. Each design is 2.85ft^3 net tuned to 33hz for a front firing setup sealed from the trunk of a 99 Pontiac Grand Am. Does anyone have any experience/input on which would work best for me as far as loading, port noise etc.?Please use "left design" and "right design" when referencing for clarity as I am unsure what to call each one specifically. Note: I will not be adding any 45's within the port, but each edge will be…

Subs: 2 dual 2 12" sa's Amp: kicker 2500.1 Car: 01 monte carlo Currently I have a 3.5cu box with a slot port, both fired towards the rear. They were fired into the cabin and I got a 140.x. I was told firing them the other way (how they are now) would post better numbers. I've yet to get metered though and can't tell a difference by ear. The plan is to build a new box with a 6" aero port firing to the right with subs facing back. Can anyone chime in with a better suggestion or confirm this would post good numbers? -Thanks

Getting ready to do a little sound deadening this weekend. This is going into an 07 Altima. Do I need to remove any factory deadener that is glued to the floorboard or any other place. I'm not talking about any jute carpet or material that can be easily removed with my hands. I know that some cars have factory carpet/rubber like padding on the floorboards, does this need to get removed or can I just deaden around it? Thanks. Thanks!!! :drink40:

so I just took everything out of my trunk. which also includes the rug and spare tire. I'm not putting the tire back since I can't get it out when everything is in. so my question is should I put the rug back in? I thought I read somewhere rugs are bad for spl. thanks.

I don't want to keep bugging Jacob if other people here can help. I am building a ported enclosure for 2 Sundown SA 12's . A few questions , would it be good to tune them at 36hz? They will be on a Sundown 1500. Also, What i really need to know more then anything is the port dimensions. The max dimensions for my trunk is 22 Depth, 33 length, 16 Height. A sketch up would be really appreciated with the port calculated and what not! I will return the favor in some way *Shizzon are you around?*

I finished my fiberglass box yesterday for 1 15" icon yesterday, kinda anyway. Its a little on the small side at 1.8 cubes. I plan on adding some polyfill to bring it up to ssa's specs for 2-2.5 cubes. I just dont know how much to add, I have a 20 oz bag of polyfill at the house. Any advice?

I've got these comps installed in my jeep with the tweets mounted on the doors @ the front corner of the window. As of now I'm running a reference 500 to them but plan on switching amps in the very near future. even with the crossovers @ -6db the tweets sound way too high and ear piercing. Does anyone have any experience with these comps? Any suggestions on making them sound a little better?

I need a box for.4 12 sa ported to be put in a 99 crownvic can anybody.help me this and a set price would be nice i live in fla

Ok ppl I will be making a ported box for my subs, my external dimme. are 38" wide by 14" height and 17" in depth,, My question is, I will like to tune it to 35hz or a bit lower are these dimme ok ? my subs are HX2 12 "punch series dvc 4 ohms will this be ok ??? in order to be on the right step...... ok at this time I'm using bass box pro 6, I'm trying to get the hang out of it ok anybody correct me if I'm wrong ,vent side will be 12.5 height + 12.25 long and 2 inch from side wall (26.75 sq inch port) tuned to almost 35 ........

I'm trying to figure out my next box. The program I'm using is tells me that my port will be 5Tx10Wx17.5D. Now how much of an effect will it have if I was to change the opening to 3.5Tx11.5Wx17.5D?? I'm looking to tune it to 34Hz. Thx from the help.

I cant decide if i want my port to be in the middle of my 2 18's or @ the bottom below my 18's people reply back asap thanks=]

Never used allthread in a high pressure install so need some small tips in this area. I know that when allthread is ran from one side to another that washers and nuts are used on both sides of a wall. So that means 1 run of allthread will have 4 washers and 4 nuts on it. What kind of washers and nuts am i suppose to use inside of the box to prevent them from coming loose? I looked at nylon lock nuts but i cant use those on the inside because to get the nuts on the inside, you have to roll em on before you slide the allthread through the other wall. So, roll nut one way then back the other way to lock in place... nylon nuts appear to only roll in one direction so i dont k…

Hey guys I was wondering if I could get some help for a box design. I messed up my first design as my box fits inside my car but I FORGOT to measure the opening of my trunk to put the box in which doesn't allow it to slide right in. I am coming to you guys for a design for the Fi 15" BTL. And the car I have is a 95 Honda Accord. Max width I will go is 35" and the height will 16.5". Was looking for maybe 4 cubes of space @ 35Hz. I would really appreciate the help and thanks in advance! -Curt

Hope this is the right section. Anyone in the Myrtle Beach/Conway area we are having a metering session Dec 8 at Carolina Audio in Conway. Call 843-455-9121 for info/directions. It's not a show or competition per-say because we won't have trophies or classes, and it's not really a show because there's no forms to fill out etc. Just stop by if you want to get metered on a Termlab for a good price. I hope I posted this in the right place because it was originally meant to be a competition, but we didn't get things really together in time and it's just not going to be big enough to have classes or trophies. Should be fun though, and get a nice offical T/L score without the l…

Today's massive frames and motors add challenges to designing enclosures these days. What is the general "rule of thumb" for the minimum acceptable distance from the back of the woofer's motor/pole piece vent hole and the back wall of the enclosure, or a port wall? I'm playing around with different designs for an older Rockford Fosgate T210D4. I can handle the designs myself, I just need some input in this area. Thanks in advance!

Is there a major sound difference for a 12" from 2.30 Cu. Ft. to 2.50 Cu. Ft.??

I was thinking about to the standard square ports, but last night I thought about doing one, maybe two, larger round ports using PVC. Has anyone tried this. I was thinking something like 8" diameter ports, maybe two of them. Since it is going in a blowthrough, is it also okay to extend the ports out a little, maybe almost into the blowthrough to ensure more pressure from the port goes directly into the cabin of the truck.

I'm thinking about making a box for some older Rockford RFP1408's that I have, they are 200 watts RMS each, the only wood I have is a 30"x60" sheet of 1" MDF and another smaller sheet of 3/4" MDF. So, I'm gonna use the 1" sheet for most of the box, and the small 3/4" sheet for the front. 1.25 Cubic feet 1" x 11" port tuned to 33hz What do you think?

Hey all... got another question here . If you use aero ports, is it possible to build the box smaller in relation to a box with slot ports, or is the port displacement the same for both types? Thanks

There's a sanctioned USACI show about an hour and a half from here this weekend, thinking about entering in the "Consumer Q" class...anyone here have experiences with USACI SQ? I'm pretty sure the "Q" classes are just soundstage judging, no install, but I'm not sure. What are some things I should look out for so I don't get completely stomped? Thanks in advance.