US AMPS

Hi, I'm from Germany and I have bought an US Amps Merlin MD-23 Amp on Ebay earlier this year. I never opened it because I didn't have time to work on my car. Today I finally wanted to look inside my new Amp and I was shocked. On the Packaging Box and the Chassis it says MD-23 but on the Board it says MD-22. So I guess I was deceived by the Ebay seller. But I wanted to be sure, so is there any attribute that could tell for sure which Amp I do have here? I'm looking forward to any reply you can give me =) Greets Eric

I just purchased a set of XXX6.5 components from RE and would like to run it active. Would you guys be able to give the the ideal crossover points at what slope to run the mids and the tweeters ? There was no white paper/specs that was included in the box my gear consists of Alpine 9887 Audison VR209 (200w x 2 @2ohms) to the Mids Audison VR203 (70w x 2 @2ohms) to the tweeters Audiosystem amp 780watts@2ohms RE SE12 @ 1.1cuft sealed box Thanks and hoping for a quick reply

I was wondering if anyone has had any experience with the MD-3; is it worth the money? And if so would it be a good match with a 15 fi btl?

Hey I have a US Amps MD2D that the remote wire screw on it happened to break off in the hole that you screw it into. I was wondering how would I go about replacing the power ground remote block for it and how much that would cost. The amp was bought from an authorized seller at the time around 2 and 1/2 years ago. Its a 2005/6 model.

i have 2 RE SR 10 D4's so which us amp do i need? i might do eight later. The set up is in a 97 S-10 blazer so i have some room. what kind of current draw should i expect? my blazer is all blacked out so black would be sweet but what ever works...

Here it is guys, your chance to have your girl be the RE Audio spokes model for US Amps/ RE Audio at SEMA 2008 and CES 2009. Please send pics to [email protected] or [email protected] for approval. Please include all contact info. If your girl is lucky enough to be chosen we will fly her to Las Vegas and Pay for her hotel while she is there.

was wondering if i can strap 2 of these amps together???

does US amps have any dealers in Pa? Now with Kove making a return i am thinking about running some kove/us amps again. thank you.

Well due to everyone blowing me up here is a sneak preview and pricing just for SSA members. I will be selling these untill they are gone, Everyone of these will have a 1 free recone warranty, but you must pay shipping to and from for the warranty. 12D2 or D4's 219.99 15D2 or D4's 249.99 18D2 or D4's 289.99 These are shipped prices to the continuous 48 states only. D2 or D4's

Both Mrd-m1005 (alpine) and Usa 2000x produce 1000W as I have the Usa running on one channel (time being). However, the Usa blows the Alpine out of the water. I am also getting less dimming then I did with the Digital amp which seems ass backwards to me. Can anyone shed some light so I can understand this more? Thanks Btw, I love this amp!

never seen a re forum... jus curious on wut kind of numbers people are putting out wit a single 12" SX....

Hello I'm new to this forum. I have a few questions that I would like for someone to answer for me. I have the like the title states a US Merlin MD22. Now every where i have read says it do the following specs Power: 200wx2 @ 4 310wx2 @ 2 650wx1 @ 4. And on the box it says 257 @ 4 ohms and 352 @ 2 ohms. So I want to know the truth, whats the deal? The first thing i noticed is the fuse rating (3) 25 amps, now i know that if a amp has a 60 amp fuse. It will do somewhere from 650 to 750 watts. And the second thing I noticed was the power and ground connectors. Now I know it takes like a 4gauge wire. And the thrid things is that it is made in the U.S.A. so I know that its …

Just sent this to "tech-at-usamps.com"

hey guys i just bought a DE-1000 but it did not come with a bass control or the usamps logo. Where can i buy these?? also does anyone have the specs to the de-1000? i posted in another thread but i didn't get any replies.

To anybody that uses the Merlins.I am upgrading my electrical to meet the demands of all my amps( 5 Amplifiers) Three amps are the PhoenixGold Ti Series (2 600's Ti and 1 400 Ti) Two US Amps MD3D 07 Models.I can not give you the exact wattage but both amps and subs are connected at three ohm on a JL Audio 13w7. All the amps that I have are unregulated power supply and need alot of juice including the two merlins md3d amps. On the merlins the amp load is 480 in my car adding another 220 plus that is a total of 660 .I had one high output at 220 240 maybe hot.That was not enough so I am adding two more alternators that put out at least 400 to 440 amps.Beside some for t…

Hey guys ive had an AX4300 for about a year now and one of my channels doesn't work properly. It seems that the rear right channel will give a very scratchy sound like the speaker is blown. i went back and checked the RCAs and they were plugged in fine. if i jiggled the rca or pushed it in harder it would clear up for a while but then the sound comes back. What is going on and how can i fix it!!?! Thank you

Hi all, I'm new! My name is Francesco, from Italy Two questions: 1. Where I can find U.S. Amps IS2150 Manual? 2. Today I tested it but there's a little problem... If I put signal on right input channel I find speaker output on left channel and viceversa! The board is REV. A. Is possible that the IN-OUT RCA serigraphy is wrong? (Normally RED is right and WHITE is left...) I also find some distorsion on both channel but i'm not fully sure because I used only a 200mm woofer. Power cable in photo is just to test it..if it works I give it a 2AWG Some photos: I hope you can help me, thanks in advance!!

I'm sorry to say I don't know much about U.S. amps. I have 2 that I'm trying to find some info on. Value, wattage etc.. any info would be much appreciated!

i need a us amp md2d very very soon for the 15s, who knows where i can get one from for cheap would really appreciate it trying to spend like 350 checked ikesound they had one for $299 but the pic didn't look like the one i want but the title said it was right so please help

Have 4 fresh Usa 2000's that have never seen power. Going to run one one my FI Bl 15 in my 2001 Nissan Maxima with aftermarket battery and stock alt. I wont be killing this setup but will it not kill my system until I get an 130Amp alt for it...And possibly a second battery if I need to??? Again, I wont be pushing it way too hard but ive heard these amps draw alot of current.

hallo, im new on this forum im from the netherlands and im i litle us amp colector i'm looking for info about my hobby so thats wy im on this forum plaese check out my pics en tell wath's your opinion maby you have a collection yourself please show it i love them sorry for my inglish Thats my usa 400 and my vlx 25 thats my 100hc an my usa 400 again

Hey man can you get my a cover for a US Amps us-x3 and a VLX-400 end cap? LMK man.

i just installed an md2d in place of a hifonics bxi1606d. before i had installed the md2d, i tested it and it was fine. when i finally screwed the md2d amp in place of the hifonics and hooked everything up, it didnt turn on. i checked the fuses and they were blown. i replace the fuses and they blew again. the set-up and wiring is the same as it was with the hifonics. i just switch the hifonics out and the m2d2 in. what am i doing wrong. the grounds and wires are all okay. i even tried it with the remote turn-on lead out and the speaker wires out and rcas out. and i tried it with the dual amp disconnected from the setup as well. what do i do? o and the bxi1606d had 140A t…

ok...got all ready to turn on the 600x I just got...did....nothing...then looked at it again....no remote turn on terminal...where does the wire go to turn it on.... the manual online doesnt show anything on the amp connected to the remote wire off the deck...or else I am not getting the obvious...haha.. cant believe I have to ask this...