Sundown Audio

How do I measure it? I have a pair of 1500s strapped on three Fi Bl 18s (dual 2ohm) in a series/parallel configuration. I've already clamped the amplifiers and they are pulling 460a of current, voltage drops from 14.4 to 11.8, and resting resistance is 1ohm. What else is there?

demos/bails/term lab. check it out rate it 5* (or w/e the new thing youtube has going), comment, and subscribe! Thanks!

I have a sax 100.4 and the crossovers on this amp are awesome! My question...Whould an Alpine Imprint Sys improve the sound, or just use the crossovers on the amp.

OK, so I need some help on strapping amps. I

Well I just received my SAX-125.2 not too long ago and WOW! This is a very nice amp with sweet sound clarity. I put it to my polkmomo 6x9's and it blows my overrated crunch ( I know, I know) out of the water. I just started getting back into car audio not too long ago and went cheap just to get started. Sundown for life now!!! Then you had to go and have this sale for July and u can bet I will take advantage. Before this month is over I will be ordering an SAX-100.4 and the 50.4 fo sho. Then the 4500d will ship (hopefully) in October...Christmas all year long for me!!! Hopefully during the build I can get some pics going but it be awhile. Thanks for the great service and…

I can either get a second SAZ-2000 or a single SAZ-3500. I am leaning more towards getting the second SAZ-2000 so I can have more power. But I like the thought of having a single powerful amp. But on another note, I am VERY impressed with the 2000, it does more then rated power all day without getting more then luke warm. my SAX-100.4 gets warmer then the 2000 does. These will be powering two RE MT 18"s

Went to our local TBP event here in Fort Worth(other side of world for me)....100 mile round trip... Threw in 1 of my Sundown Audio 3000D's with all 3 DEKA 9A31's and 2 12" JBL Power Series subwoofers in a 34Hz box with a final impedance of 2 ohm at the amplfier...Decided I wanted to burp them....so I pulled up in the lanes....and burped a 147.0 and a 147.3 which was barely enough to scrape out 1st place....2nd place did a 147.1... I was pretty happy for what I was running and how I had it set-up, it did higher than I predicted.... I'm going to fiberglass this enclosure, and cut the port to about 45Hz, and burp me a 150+.... It's going to be something to see.. One of my…

Okay if I've done my math correct, the 3500D (with a 350A fuse), I should be able to power this thing with a 250 amp alternator and (2) D3100's (117 AH each) running at 1 ohm on (2) of the of the Z15's?

Ok, the last couple of shows I've been to I have been down a few tenths. 157 at the Vinny, 156.9 this weekends Madvette show. I know my voltage has been an issue, but I'm working on that. So I discovered (by accident) another way to wire my subs to a lower load, and my amps don't go into protect.

anyone know this off hand?

I'm not seeing any new e-mail in my box since 7:30 PM last night... just a heads up in case anyone e-mailed me since then. I'm not sure if I'm going to get them later or if they are lost, my server is not responding at the moment.

do you guys have a shop in statsville, NC it says my package is comming from their and thats not but a 2 hours away im just curious.

I have breifly looked but can some please tell me how to wire my saz1500 v2 to my FI 2ohm sub for a 1ohm load. Also does it matter which way the rca's are in? (They are not colored red and white on the amp) Pics would be awesome. I know these may be dumb questions but its the last thing for me to do.

Corey Mitchell 1 Sundown 1500D and one 12" Nightshade @ 34Hz 1st place Drive-By 1 with a 118.6 (40 amps of fusing) 1st place in Street 1 with a 142.9 (40 amps of fusing) Jeremy McCord 2 Sundown 3000Ds and three 15" Nightshades @ 43Hz 1st place in Drive-By 4 with a 129.7 (320 amps of fusing) 1st place in MOD 3 with a 151.4 (145 amps of fusing) Drive-By Best of Show Josh Newton 4 Sundown 1500Ds and 8 15" MA Audio XLs @ 31Hz 1st place in MOD 4 with a 155.1 (240 amps of fusing) 1st place in Drive-By 5 with a 127.0 (no fusing) SPL Best of Show Derek Jackson 2 Sundown 1500Ds and two 12" Nightshades @ 50Hz 1st place in Street 2 with a 149.8 (60 amps of fusing) 2nd place in Drive…

well we had another good showing today at a great show down in elizabethtown.. was a little hot though.. Derek 1st place Street 2 with another 148.. PHAT CAR award!!! Corey 2nd place Street 1 with I believe a 145.3 1st place Drive by 1 with 121.8 Seth 2nd place Amatuer Street 1 with a 143.4 Jeremy 1st place Mod 2 with a 150.4 "playing music the entire SPL run.. hehe" 1st Place Drive By 2 with a killer 129.1 "lookin for a 130 but just too hott" Also Drive By Best of Show also another member of our team that doesnt have sundown stuff yet Josh 1st place Mod 5 152.3 have a few pics on the way

Well the more I study the x-over section on the 50.4, the more unsure I am. Basically I want to run two channels to my 6.5 " mid-bass. I'm planning on using the LPF on my HU so I just need to x-over the top end, not sure where yet. Then the other two channels to my tweets thru HPF on amp. The sub-sonic filters on both sets of channels has me a little confused. Could someone be so kind as to tell me a good starting point on ALL switches? Also I'm running one set of RCA's to the amp and the other set to my sub amp. Can I use just one set of inputs or do I need to use Y adapters (would rather not do that because of any signal degradation, tho probably not much). Than…

Here are a few vids I shot of the cracked night shade in action powered by my new purchased 3500. Thanks for the enclosure tip jacob sounds great. Dont beat me up on the install so busy working makeing everyone else car look good. Its just temp. anyway going to send it off for a recone soon.

I understand the concept of bridging and individual channels and the impedences that the amp handle. What i dont understand is that load that would be created in a 6 channel tri mode on the 100.4. I am planning to get this amp and rainbow slc 265.25 ng's for my fronts and rear doors and they are 4-ohm comps. Np with that but i was peaking at the manual and noticed you could do a 6 channel tri mode and if i added mid bass or subwoofers, what wattage and impedence would be put onto the amp. This is a concern because i don't want to ruin any speakers that i add. I am really trying to create a good sounding system, i care more about bass created by speakers than having to…

havent seen any available on SSA site. just wondering where can i pick up a set of 15"s. just preordered the 3500d lookin for something that can hang. also order 100.4 need components for that too. i have a set of 3 way components but i dont know if i wanna use them they are 350 watts rms.

i told him to order it before the end of june. he really liked the way it pushed my type r's. also when i bought my amp from chad (lilmaniac2 at roe.com) i didn't get the stickers that you send out normally with the amp. how much would you charge shipped to 62025 for the 2 stickers?

was just wondering what kind of numbers you all are seeing out of them. i know i already read the amp testing thread was just wondering from other people who are using them as well.

All, I posted recently looking for assistance with a box build for (2) SA-10's. If you guys have a chance, please comment with some suggestions. Bandpass box for (2) SA-10's Thanks

would this amp suit these subs? or would it need less juice for these subs? i hear the E8s can take 800 but RMS is 200...JWing...looking for a good resonably priced setup... thnx Doyle

Got my 1200d yesterday, SWEET amp! one thing I still need though, A remote gain knob. Anyone have one taking up space and want to part with it? I need to be able to turn it down when the wife is in the car. Thanks all! David By the way, this amp is a healthy beast!

Am looking at the T/S parameters for the SA-12 and noticed that the D2’s RE is listed as 4.33 Ohms when tested in series. From what I’m used to seeing, the RE values are typically less than the advertised impedance rating so the 4.33 feels a bit high for a sub with dual 2 ohm coils. The D4's RE value of 7.09 is right in line with what I'd expect. Could someone please help me understand what’s going on here with the D2? Thanks!