Sundown Audio

Hey i have a sundown Saz-1000D amp and my dog chewed through my bass gain control wire. I just wanted to check if there was a certain type of replacement wire i should get or if it didn't have to be the same exact wire. and where do you get those wires? thanks for the help

Here is a link to some pics and videos ,from a show this past weekend http://forum.realmofexcursion.com/showthre...ost&t=56773

SA-12 cone, spider, dust cap, coil + 4-spoke frame w/ 6.25 mm spacers Atomic Apocalypse 2.5" Coil Motor Going to measure T/S specs tomorrow

Video Caption : Purposely tearing up an E-10 to demonstrate what it takes to do so. We are seeing *clamped* power of 50-100% of the woofers rating with NO BOX for 3-4 minutes straight in order to hurt the woofer. When using an amplifier rated for 400-500 RMS on these woofers in a day to day situation it will be EXTREMELY difficult to damage them. Again... this was intentional abuse -- any person hearing the type of mechanical noises we did in this testing would obviously turn it down =)

Been here all weekend with customers and whatnot anyway... so decided to drop one in the Jeep real quick. The Jeep hasn't had much love lately and I was using it to haul scrap metal for a while (hence the wooden truck bed) but I decided to break it back out. One 4500D @ 1 ohm with one extra SPV-70 for battery. My box has a pretty high rise so probably seeing 3-4 ohms or so actual on the amp so not a ridiculous amount of juice yet. Sub still has a good bit of usable throw remaining. So I guess the next phase is to actually put in a more usable battery setup for multiple amps and use two amps at 0.5 ohm to get the sub to full stroke. Not sure yet if that will get done …

Hey guys I've got a question for ya, on the 100.4 you can run 2 mids and 1/2 subs on it right? I'm not sure on the wiring on it, I think I might be right though? 100wx2 @ 4 ohm stereo (mids) and 320W x 1 @ 4 ohms Would that be right for two mids and a sub on it? What I have now is a 1500, and a 10" FI BL in my s10. All I really listen to is hard rock anymore, so the 1500 I have now is more or so less useless to me now. Also could it be wired all 4 to mids/highs and have a sub run off of it also? I'm not sure in my wiring lol.. Would trading a 1500 for a 100.4 be a decent deal, or no? Sorry for the dumb questions Thanks

Hey Jacob you going to High Point Sunday? If so you think to can bring a 12" Sa d2 with you. I'll pay you when I get there. I was going order on monday but I'm going to be at this show anyway so I may as well compete.

anyone know all of them? i really need to know the displacement of one for the different boxes i am looking at building. thanks

http://www.sundownaudio.com/SD-1_blowout.html I added "Buy" buttons to the SD-1 blowout page for the SI BM 12" blowout sale

my best with the crx and loudest in colorado 153.7 yeah I know it's not that loud but good enough to take down a seven foot award.now i need more power jacob

Hey, I have a 12" sundown nightshade that needs a recone. I'm just wanting to know I someone can fill me in on how much it could cost. I would also like to know how much it could bbe if I wanted to recone it to a 15 if possible. Thanks guys

Ive been watching the new heatsink SAZ3K on db-r been available for 4 days and havnt came up with the money until now. I go to order it and its gone! Who took my amp?! lol

Hey guys, Looks like we lost alot of database information in the upgrade process. I was able to re-post both Sean and Loyd's test results. If anyone else has anything to re-post I would appeciate it greatly. Eg: SAE-100D photos and whatnot The new forum has lots of cool new features and we are back up and running now!

Ran a box design through WinISD and wanted some input. This is for 4 E8 8inch subs. It is a three chambered enclosure, each outside enclosure is 1 cubic foot tuned to 70 hertz. The inside enclosure is 2 cubic feet and is tuned to 40 hertz. The woofers will be mounted magnet end in the 1 cubic foot side two woofers per the 1 cubic foot side firing into the 2 cubic foot portion. This is for my kid who listens to mostly rap. Powering this will be a SAE1000d. A subsonic filter will be used to keep over excursion down. The graph on WinISD looks impressive in an open air environment. Any reason to not utilise this box design?

Hey Jacob noticed you has some prototype Comps listed in your current set up. Will we see some of these sometimes?

too start off I'm not bashing any products this was just a direct swap. we started out with this box on a 40.1 @.5 did a 154.9 then we dropped this in and only came up with this voltage drop was from 15.2 on the volt meter down to 13.4 on the 40.1 and from 15.2 down to 12.3 on the 4500 there was a nsb90 under the hood with 6 runs of wire to the back batteries they are 110lb data safes. the 40.1 was giving some crappy wave's on the TL and the sundown hard perfect wave's on every test we are going to do the 4500 on 16 volts next and see what it will do then here is a pic of the wave with the 40.1

can the sae 1200 be linked or not??????????????

So,, how do i get on team sundown? what are the requirements? let me know please i would like to be a part of it.

Is the warranty transferable on SAZ1500D's?

How long is shipping? Is it the standard three to five business days?

"The ATO style fuses in the SAE-1000D are designed to handle roughly 130% of rated current for 10 minutes per the spec sheet for around 98 amps of handling, which at 14.4 volts is almost exactly 1000 watts at 75% efficiency. Since this is not an SPL competition amp I decided to go with 3x 25 amp fuses. The prototypes had 3x 30 amp fuses and I found that they would not blow even at a 1/2 ohm load for extended periods. I went with 3x 25 amp fuses to give a warning to inexperienced users when they wire the amp too low." Also posted in the FAQ thread: http://www.soundsolutionsaudio.com/forum/i...?showtopic=7406 Item Number 4. I was seeing the question about fusing on several …

i have a 2011 4 door wrangler and want to install 2 - e8 v.2, 8" subs in the rear floor cargo area. i measured roughly .55 cubic ft., i will pour water in it to get exact..... is there enough air volume for 2, was planning to secure a 3/4" mdf baffle to the bin, bottom mount the subs. i was hoping to be able to use the stock cover and floor mat to conceal them. i have an alpine pdx 1000.1 to power them. any support would be great. thx

Just wondering how these guys are linked to you? www.emfcaraudio.com

I just want to give you a big thanks. Your customer service is second to no one. Anytime I have a question or send you an email i get a response almost instantly. I appreciate all your help through everything and I cant wait to bring some more wins to team sundown when my new car is done.

Hello .. I have a saz 3500d but I have some problems with it! Protection light is on all the time even though I have no bass coupled .. It became like this after I made ​​a mistake with the soil to the stereo so the earth by l rca cables. Have a friend who has a firm that makes amplifiers for home use that have looked at it but he says he must have the wiring diagram for saz 3500d in order to repair it. Can you help me with that? or if you think of something else can help me find a wiring diagram? Or do you have some idea of what it could be wrong? are very pleased with the amp in general and would like to fix it so I can use it! Since I live in Sweden and is suck in E…