Sundown Audio

Hey, been trying to email you, dunno if you got me on spam filter or something else wierd going on ([email protected]) You should have go that box from me last week with the shocker coil, spider, and some maple syrup. Please get back to me ASAP with a price of at least the other recone parts we discussed and a 15" basket with appropriate shipping so I can get these things built up for this weekend 3X NESPL show!

Ok I'm new to this strapping amps thing but currently I have 2 saz.3000d's and 2 21" incriminator audio dp's (they r both d1's) right now I have them both wired at 2ohms each and was wondering what kinda load am I getting out of each amp??? Am I pulling 2ohms from each amp and that wud be both amps strapped at 4ohms??? This is where I'm confused abt...also if I wire each sub down to .5 what kinda load will I pull out of each amp??? Will it be .5 out of each amp making it 1ohm strapped or will I be pulling .25 out of each amp??? Really confused was wondering if neone cud help me out thanks

In response to the current economic situation we are lowering our MAP pricing. Cost for our amps from an authorized dealer outside of a pre-order or special sale have changed as follows : SAZ-1000D : $355 OLD / $315 NEW SAZ-1500D : $570 OLD / $500 NEW SAZ-2000D : $670 OLD / $615 NEW SAX-125.2 : $255 OLD / $240 NEW SAX-100.4 : $395 OLD / $365 NEW The prices listed under "NEW" are now available at any authorized Sundown dealer. I sent out a dealer news-letter this morning, so if your dealer has any questions have them call me.

Jacob, I just wanted to thank you for having the vision and the balls to make amps like yours. I have enough power to make the Fiancee tell me I am rediculous without even having to really turn up the bass. I truly treasure my SAZ-3000. I am just waiting for better componants so I can actually turn the gain on my 100.4 up a bit and see what she will REALLY do. But that as always costs $$$ Thanks again, Jordan

So, I got my second 1000D in today. I took it straight to the truck. Hooked it up, I had them ran strapped at 2 ohm. The woofers are D2's, which were ran in parallel in the box then ran in series out side the box, bringing the total to 2 ohm. I only use the left side of the speaker connectors next to the 8awg. It worked fine, sounded good, was loud and voltage was fine. I THEN, tried to re-wire the subs. I wired them in series in the box, so each woofer went up to 4ohm, I then ran each one to the amps. I thought that it would end up bringing the ohm load to 2 ohm, so each amp would see 1ohm. When ran like this, they weren't as loud and voltage DROPPED. Horribly I wired …

How well would these perform in a HT setup? Thinkin about 2 12s off 500watts. How do they compare to Fi SSds?

going to event on monday near denver. how does it work and what kind of music do you have to play. this will be my first competition. will post pics and vids after show on monday.

Had a good time at the USACI show today in Tyler had some really nice rides and set ups here are some pictures. And My Truck SB4 - 151.4 1st run and 153.6 2nd run with port plug in tuned to 36 hz

Well since I always see so much talk about new sundown products, figured I might as well throw out the possibility of full-range coax and or component speakers. I would def. be more interested in the component speakers, especially if individual drivers designed for active or custom built passive x-overs.

I'm in the process of acquiring the rest of my system and basically the last thing I have to add is my sub amp and sub. I think I've settled on an ID Max 12 D2. I'm wondering what kind of drain running the SAE 1000D will put on my stock charging system at 1ohm. Also, I'd imagine this would be plenty amp to run an ID Max? It should have plenty of oomph if I planed on having the ID Max in a sealed enclosure in the trunk of my '03 Mazda 6. I have an Alpine MRV-1507 class A/B for my front stage. It's a bit of a current hog when bridged but when running mono it doesn't seem to drain the charging system nearly as bad. So... will running a SAE 1000D at 1 ohm onto an ID Max…

We've had some e-mail system glitches at the shop. I've been discussing it on our Facebook page the last few days -- the long of the short is that if you sent a message before February 1st and didn't get a response there is a HIGH likelihood that your message was lost; it is not being ignored but it simply isn't here. Our e-mail volume was too much for consumer e-mail programs and they freaked out a bit... various database problems. In any event our new Zendesk support ticket system for our e-mails is working very smoothly; we fired it up yesterday. If you have an e-mail in that is older than February 1st please re-send it to one of these @sundownaudio.com addresses; bran…

Ok, so I just got a new 3000d and a 100.4. My HU only had front/rear, no sub pre-amp output. Question is, if I wire the front/rear to the 100.4, if i Use the channel 1/2 output to the 3000d, will I lose my ability to use the hp/lp settings on 1 and 2 or if I do use the hp/lp will it still send a full signal through the 1/2 output? Sorry if I am not being very clear.. front / rear from head unit into 1/2 and 3/4 of the 100.4 1/2 output to 1 on 3000d will using filter controls on 100.4 impact frequency output on 1/2 output channels?

Got a small stealth box I'm putting in my car and I need a sub for it. I believe the SA-10 would work,just want to make sure.I also need advice on which amp. Here's the box specs..... .6 cu ft space,sealed. Mounting depth of 8 inches.

I'm new to Sundown equipment, and haven't owned any before. I've read so many wonderful reviews and posts by Jacob, I'm confident that the product will exceed my expectations. However, I have concerns that this will be *too big* (if that's possible). I'm considering the SAX-100.4 for my daily driver (with future uses in mind, of course). This would run my entire system, stereo for front component set (probably high-passed @ 80-100hz), and bridged rear to the sub (low-passed @ 80-100hz). The sub I have probably would hit max excursion before full output of this amp, so gain would probably be set low on the bridged channel, and low on the fronts to match. My prior exp…

Hey all I got my (2) 3500 D's and I currently have 2 of these: http://www.knukonceptz.com/productDetail.cfm?prodID=KNI-11 I have (3) 100 amp fuses in each of them..but the 3500's call for 350 amps each.... so should I upgrade and go higher with these, for a max. of 360 amps on each fuse holder http://www.knukonceptz.com/productDetail.c...rodID=MANL-120A Thanks, Freddy

Well here goes.... I have the option to either buy a 1993 s10 extcab or an astrovan. Kinda stuck on what to get. Now I have built both before for a couple guys in the area but this ones mine. Either way its going to get LOUD. Just want some ideas on which one?

Congrats to Paul Strouth MECA Member of the Month. Team Sundown FTW..

HAPPY THANKSGIVING TEAM SUNDOWN FAMILY!!!!

which amp would be the best match for a JL 13W7? SAZ-1000? I can run it at .75 ohm or 3 ohm. thanks.

Ive been watching the new heatsink SAZ3K on db-r been available for 4 days and havnt came up with the money until now. I go to order it and its gone! Who took my amp?! lol

Originally posted by Greg Kashin on my CACO Forum : http://www.caraudioclassifieds.org/forum/showthread.php?t=54443 ----- Sundown Audio z18 v.2 - the first and only z18 so far in the land that gave birth to the great Borat powered by a dd m3 @0.5

I'd like to know what's the efficiency spec. of the nightshades. I couldn't find it in the website.

I am getting ready to buy the sundown 100.4 amp and I have never done this before, but really want to try it. I am going to run the tweets of two channels and the mids off the other two channels. How do I set up the crossovers to do this? I know this may be a dumb question but I have always had external crossover's and want to run this way. Please help.

thinking about ordering the sundown 2000d, but is it free shipping?