Sundown Audio

The 10" is done and drying; should be able to play tomorrow. I'll be a tad more careful this time *laughs* Of course I should be safe with the 8 3/8" spider vs. the 9 1/4" on the 12" model as I shouldn't be able to reach quite the level of throw! This is the first 10" woofer with 3" coil that I've built that I didn't hate every second of... gives me a good feeling and I cannot wait to test it ! * Left to right : Z v.4 10 / Z v.4 12 / Z v.3 12

Z v.4 12" D1 : Z v.4 12" D2 :

The 257mm spiders showed up this morning so I assembled the 15" version today. I should be able to test it tomorrow at some point. See photos below : *257mm spider tool

Just got done unloading the trucks... the 15s and 18s are here in stock for the first time. We have additional 12D2 models for any over-flow overs as well. Any 10s either coil or 12D1 we'll still have to build until the next shipment. Also some X-18 in D2 and D4 were on the truck as well as re-stocking quantities of SA-10/12/15 and SD-2 10/12 woofers.

First video of these new parts in action -- enjoy !

https://www.youtube.com/watch?v=TNuOyo6nMwk Made a quick video last week. Also my first test on my new camcorder high-speed mode. The woofers motion looks alot more like real life.

i need to know the T/S Specifications for a sundown z v2 d2 15 and how big does an spl box need to be for it

Hello. I've got a ported 5.3 cu.ft box and 1.6k amp (my box is 1.1 cf ports and 4.2 cf for the sub) which sub would be better with my setup? the Z v3 15" or the 18" ? also I've got XS power D2400 battery. I cant get a bigger box, thats the maximum box size that I can have. is my mono will be enough for that sub? (can't change it, I'm out of budget) is that box is enough for the 18" ? if not, is it good for the 15" or is it too big? * car details: I have a Fiat Grande Punto (small car. hatchback) and my box is slanted front if it matters. Amp: Celestra FA1.6k Thanks, Udi.

Hey guys new to the audio system game looking to do my first build starting after the new year. I'm look to get a 98 4 door blazer and looking to go with a 4th order design I have 2 sundown audio saz 2500d V2. My question is is the saz 2500d V2 enough power for Z v4 most likely looking at the 15s or should I upgraded to the saz 3500d yall thoughts would be greatly appreciated

ok a freind of mine came down and i ran some 8 gauge to his z1 to my car. my car with 1 nsb-90 and 4 runs 0 gauge did a 150.7 @ 1ohm on the TL my car hooked to the z1 with high output alt a nsb-90 and kinetik 2400 2 feet from the z1 did a 150.2 @ 1ohm we did get 1 test @ .4 ohm and it did a 152.2 but did'nt have enough time to mess around because we needed to recone his xxx's but i will be adding a very large battery to my system to see if i can't get my amp's to do .4 ohm for a show on saturday and i will post number's later this week

Okay I'm looking to upgrade from the SA-12's to the new Z12's. I'm going to be powering them with a SAZ-3500D. My concern is designing a new enclosure. I have a slot ported enclosure (3.5 cubes tuned to 32Hz) I would like a ported enclosure using aero ports. My current enclosure measures 36" x 19" x 17". I would like to keep it around that size, any ideas would be appreciated

I finally got this box built and a chance to test this speaker out. It is replacing 2 15" polkmomo drivers on a crunch amp. The box is roughly the same size as the other but this one lets the seat lock into the up position. It is about 3.25 ft3 at 35hz. There is no bracing or 45's in the corners. Its facing up right now as I find a place for the amp(s). But it sounds better forward. I know its a little ghetto but Ive just recently started building my own stuff. As you can see it is hooked up to the SAX125.2. It is bridged at 4 ohm so its only about 450 watts. Gain up halfway and it still rocks. This driver sounds very nice. This driver is of high quality and great sound.…

Z15 Pre-Sale in Effect as of today. The ETA is mid February on these. MSRP is $449 on these! D4 and D2 coils will be available - limited quantity for the first run, so these won't last. $300 shipped in the continental USA for one. $570 shipped in the continental USA for two. $1100 shipped in the continental USA for four. 10% off pre-orders placed before January 15th Paypal to [email protected] More than four please contact me. T/S Specs for 15" D4 model (D2 will be very similar): Revc= 6.150 Ohm series Fs= 28.585 Hz Sd= 83.000m M

We did 148.6 on the first run but we didn't take a picture... got hot after a couple of burps so it went down a hair We have four 1500Ds @ 2 ohms each on it, no clue on actual power after rise - but I think it would actually sustain more on a burp. Not bad for my upcoming 1000-watt rated woofer, huh ?

Which would be better off 1200rms? ""SQL"" wise

What do yall think about 4 Z15"s in 16^3 tuned to 32 with a SAZ-1000D per woofer? Time to get musical in the truck.

As the title states, trying to find the displacement on Sundown Z18v.3's. I've tried for the last several hours using google and searching on several forums to get the info on these beasts. Thanks in advance to whoever can help.

whats the rms on the zv.2 subs? also whats the recommended box and tuning on a 12" and 15"?

i need as much input as possible what sub would u recommend over the other the zv3 or x series