Sundown Audio

Yep... you read that right. Hank is doing 48x SA-10s. ----- Hank is now in NC with us -- the above was done up in Indiana at his home. Subs all tested and laid out for installation :

http://www.woofersetc.com/p9251/SAZ4500D--Sundown-Audio-4500W-1Channel-Monoblock-Amplifier.htm

hey do you guys just sell the bass knob for the sundown saz2000d mines acting up it goes to 1/2 and stops pluss when you go to 0 it doesnt get low it stays on.

A customer ordered four 15s and I am just about done with the first so I took a few pictures along the build process : * Rear triple joint glue and ring - the ring is smaller than the gap and centered so can go down into the gap at extremely high rearward throw. * Close-up of the glue. * Spider pack is pressed with a laser cut steel plate and a Z v.2 motor to ensure good bonding of the glue between the frame and spider layers. * Terminals have a locking toothed washer * Soldered - and a dab of glue added to the stud on top of the nut and washer for long term safety. * Special surround glue - dries flexible and won't hurt the surround material. * Finished cone to s…

Called my shipping company and they say I should have my pallets on Tuesday -- would be sooner but Holiday closings are delaying it a bit. So... we'll be shipping as many amps as we can next week, hope to have pre-orders cleared out by Friday next week.

so i am new here just kind of feeling out a system for my daily driver(91 civic hatchback) i want to keep the rear hatch for the most part seeing as i do take my kid in it sometimes and have to randomly carry little stuff back there so i was thinking either 1 of the sa-8's in a t line(really want to build one they look sweet) if i have the room i know they can get to be pretty large or do 2 in a box around 1.5 cubes i will be powering what ever with a planet audio big bang 950 so 650x1 at 2 ohms that should work really well on a single or a pair. keep in mind i am not trying for huge numbers just something cool that make people go wtf 8's no way and be decently loud. any …

So I got my 2500D, and I just realized that it doesn't have an internal fuse. So what to do? Fuse the + lead about a foot from the amp? Why doesn't it have a built in fuse anyway? Just wondering.

I bought a SAX-100.4 a long time ago and had it installed in my last car for about 1 year, and I had it sitting in my garage since then. I recently hooked it up into my current car and am having a strange problem. I am only running front speakers with a small sub eventually to come. So I ran the speaker cable from the front speakers to Channel 1 and 2. I then plugged Channel 1 and 2 RCA's into the Front Left-Right on my Alpine 9886 HU. When I listen to a song music only comes out the drivers side properly. I try plugging the RCA from Channel 1 into Channel 2 on the amp and no sound. Plug either RCA into channel 1 and sounds on the drivers side. Plug either into Ch…

I got my SA-10's last week. And probably won't have them installed for another month. So if you've got your SA-10's up and running. Let's see some pics and or vids of your setup. I'll be running 2 SA-10's in 2.5 cu ft@32hz wired to 1 ohm off my SAZ-1500d.

I am not planning an 8" for this line any time soon... but I am planning 10s, 12s, and 15s... also... I do not have an ETA just yet, first prototypes are on the way then testing will be in order for a while to make sure the design suits all of my requirements. Just though I would offer a sneak peak of the 15" model. Initial MSRP also posted... may be subject to small changes based on tweaks needed. I AM planning to use spring loaded push terminals on production... I don't like the spade connectors. Some T/S Specs measured on the Klippel machine at the factory... I will measure them myself as well once my prototypes arrive. 10" S4 Coil MSRP: $130 Re: 3.86 ohms Fs: 31.8 Hz…

After numerous death threats (JK) I decided to stay late and post some pictures *laughs* Here you go guys : This particular one is about to be built for Brandon's truck.

Finally getting started. Car already had a system. Its about 6 or so years old. Going to redo all of it from battery back. New system includes Replacing 4g with Shok 0g. (in the mail now) New Battery Alpine Type R Components (alrdy in car) Alpine deck (alrdy in car) JL 6W0 in rear spots for midbass (alrdy in car) Front half and doors ardy has Dynomat Extrme Doing hatch in second skin (in the mail) also adding luxury liner pro to doors and rear finder wells SD 100.4D for components and midbass (aldry have) SD 1500D for subs (still need this one, so if anyone has a used one shoot me a pm) 4 SA-8s running 1ohm (alrdy have) start with pic of car and old hatch that…

I was planning on switching to four nightshade 12's but the sa 12's are looking very attractive to me now. Jacob I saw you had four of them on two 3500d's how did they hold up. I have two 3000d's on four dd3512's right now and this is the third time I have had a motor shift and they are far away for warranty work vs sundown. Money isn't really an issue but I wanna get the most bang for my buck. The car is a daily driver. And I'm very careful with the gain nob. Is the output of the sa comparable to the 3512 sub

GIANT 8" Sundown Audio Pen - $5.00 each (Add $3.00 for additional after the first one) Sundown Screw Driver Tool - $7.50 each (Add $5.00 for additional after the first one) Sundown Drink Cooler - $7.00 each (Add $4.50 for additional after the first one) Paypal to [email protected] with a list of what you are ordering!

looking for a bass knob that works with the sae 1200d v.2, willing to buy from anybody that has one.

Ok I'm running 4 12" subs on a 3k @ .5 but i'm planning to change to 4 SA-12 d2's. I'm wondering if I get more power out of 2 1500's strap @ 1 ohm then I would out of the 3k @ .25?

Two Stinger SPV-70 Batteries / 40-amp Power Supply / 8 awg wire power and Ground (this amp should have 4 awg) Wired to 1 ohm nominal : 1170 Watts @ 12.5 volts 1.97 ohms after impedance rise Wired to 0.5 ohm nominal : 1490 Watts @ 11.1 volts 0.85 ohms after impedance rise --- Measured with my Extech True RMS power clamp meter several seconds into the tone @ 60 Hz -- this typically reads about ~15-16% less than a "dual peak hold" amp clamp test. We'll do some more testing with a more adequate power wire coming up soon. The test bench 4 awg has the ends tinned so is a bit too big to go into the SAX-1200D terminals -- will need to get it in a vehicle.

If you have sent an email and it's been OVER 10 days with no response please re-send... got backlogged and I may have missed it.

Any idea on what kind of power I could expect out of the 2500 at 18 volts wired down too .25?

So today i noticed something interesting regarding my SAX100.4. I am currently running no subs (waiting for my saz2500(2) to come in) so my setup is the big 3, h/o, 2-nsb90, 2-zapco RB13.2 comps and the 100.4 so let me see if i can explain this issue correctly... here is my door panels for starters so i currently have all 4 channels in use and the crossover point is 80hz channel 1/2 - is 1 set of gains and filters (hpf) channel 3/4 - is another set of gains and filters (hpf) i am at the 1x range and hpf on channel 1/2 i have the gain set to 1/4 of the way up (just positioning i am not a noob it is for reference sakes) to match the output of 1/2 i have to set 3/4 gain…

Some may recognize it * 8 runs of + and 8 runs of - wire... getting new custom copper blocks made for the battery (XS Power D3100). Street-B is the goal for this car. Should be fun ! Something I've never tried.

i am currently running 4 10's and i will be running 2 1200d's would i be better off running 1 amp per 2 subs or should i strap them both and run to all 4?

ORDERING NOW OPEN ! My ETA for these is mid to late May 2010. There are NO refunds on pre-orders whatsoever -- so please make sure you can afford to be without this money until they arrive before ordering. TO ORDER PAYPAL ME AT [email protected] AND SPECIFY HOW MANY and D2 or D4 coils !!! If you order before the end of February the price will be as follows : 1x SA-10 = $150 2x SA-10 = $140 each 4x or more SA-10 = $130 each Shipped in continental 48 states cost. If you order after February until the pre-order is over the price will be as follows : 1x SA-10 = $160 2x SA-10 = $150 each 4x or more SA-10 = $140 each Shipped in continental 48 states cost. All shipping i…

just had to make a post to you guys for an absolutly amazing amplifier had it for 2 weeks now and it is an absolute machine thanks for one of the beefiest amps ive seen and heard the amp i'm refering to is the saz2000d too bad they discontinued it but will deffinatly be sticking with sundown

Pre-ordering NOW OPEN... pre-order runs until July 4th or while supplies last. ETA is the end of July -- as always this is subject to delays and is not set in stone! Before opening ordering 20% of this run is already accounted for in large Team builds... so get them early if you want them from the first run. COST : $525 shipped in the continental USA - Regular MAP Pricing is $775 * Contact me for AK and HI orders * USA ONLY SALE TO ORDER PAYPAL ME AT [email protected] with Subject "SAZ-2500D Pre-Order" or talk to your favorite online or local Sundown Audio dealer. ---------- This amp is a beast... it has the output section of the SAZ-3000D and a strong power suppl…