Sundown Audio

Ok where to order my sa 8s from ? SSa store? and can somone tell my the speaker displacement of these? Thanks

Does the saz1500 have a signal output, so you could run rcas from it to another amp? I'm thinking about getting a smaller amp for mids and highs and wanted to know if I would have to run another set of rcas from deck? Or if the saz could output it. Thanks

jacob, i sent you an email about this, but you're stacked up on those. can i get a set?

Okay guys... everyone is knocking my door down to pre-order these so I am going to open it up now with an early-bird special as well. My ETA for these is mid to late February or so next year (2010). There are NO refunds on pre-orders whatsoever -- so please make sure you can afford to be without this money until they arrive before ordering. TO ORDER PAYPAL ME AT [email protected] AND SPECIFY HOW MANY and D2 or D4 coils !!! Test results will be available soon If you order before the end of November the price will be as follows : 1x SA-8 = $109 2x SA-8 = $99 each 4x or more SA-8 = $90 each Shipped in continental 48 states cost. If you order after November until the…

Pre-ordering NOW OPEN... pre-order runs until July 4th or while supplies last. ETA is the end of July -- as always this is subject to delays and is not set in stone! COST : $315 shipped in the continental USA - Regular MAP Pricing is $375 * Contact me for AK and HI orders * USA ONLY SALE IF YOU ORDER BY the end of May it will only be $300 each shipped in the continental 48 states! TO ORDER PAYPAL ME AT [email protected] with Subject "SAX-1200D Pre-Order" or talk to your favorite online or local Sundown Audio dealer. ----- This is an all new board tooling developed just for Sundown Audio. RATINGS: 1200 x 1 @ 1 ohm 720 x 1 @ 2 ohms 360 x 1 @ 4 ohms ** -- Clamp testi…

I was just wondering if I have 2 sa8 on a saz1000 wired at .5 ohm will I be getting 1000 actual watts to the sub? I have a 250 amp alt, and odyssey pc1750 battery

I'm pretty sure I'm ADDICTED..

What the minimum and maximum voltage u could run...say a 100.4...or 4500d...what would be the safest for a 16volt system for a 4500d?

any one know what i should set my saz-3000D for at 1.5 ohm's? or just set it for a 2 ohm load?

Trying to wire up now- not worried about what ohm to wire it up to got that i got 3 and i am wiring it to 1.33 ohms and i was gonna just use the wire terminal as a jumper to get the neutral and power wire to the other subs like 2 wires on the terminals on 2 of the subs and the last sub will just have 1 wire into all the terminals because i dont have to jump it on the far end so my question is can two 12 gauge wires fit in one of the terminal in the sa8-- if not would it be better to run a seperate run for each speaker to where the wires are coming into the box- or would wire nutting them and getting a good tape job be good enough cant wait to try these out-to make su…

Built a pair of drop-ins for a customer so I took a few shots. Yes... we stock parts even for our 2" coil drivers - I can't stand to see sub motors get thrown away (hang on E8 v.1 guys... working on updated parts for those). * Top triple joint action - we assemble these ourselves so it's all done with heavy duty CA glue like the Z v.2 and Nightshades. * Side view. Surround is a little bowed from sitting in it's shipping box, the cone is straight no problem * Rear triple joint support ring in place like the bigger SA woofers. * Your SA-8 make a ticking sound at high excursion? Guess what ? It moved about 28mm rearward and your triple joint ring hit the top plate. Need…

I just had my first time on the meter today at Slamology and I didn't do too bad, a 140.5db. The enclosure is 5cu net (to oversized for big power) tuned to 33hz (obviously not spl oriented) ran off a Sundown SAZ-1500D@ 1ohm. For a system that is made to get low and have moderate volume ability, it exceeds expectations. I did lots of demos and impressed the hell out of people that gave "just 8's" a chance SUNDWON AUDIO FTMFW!!!! BTW- the vehicle is an 07 Ford Escape and I believe that there is more in this current setup

We still have them in stock after filling pre-orders. I also have more 12s and more 8s coming in 3 weeks or so.

Need help on deciding which amp to choose to run my 2 - sa8s?

Had alot of requests for pricing so here it is. Standard (you can pick 2 or 3 spiders): 10" - $415 / MSRP - $535 12" - $425 / MSRP - $550 15" - $440 / MSRP - $570 18" - $480 / MSRP - $620 OPTIONS: Double tinsel leads* - Add $10 Nightshade Cone** - Add $10 Nightshade Spiders (you can pick 2 or 3)*** - Add $20 Additional spiders (more than 3)**** - Add $5 each * - If you will be running an amp at 0.5 ohm or more than 2000 watts or so I suggest this. Generally speaking you will not need it if you are not an SPL competitor putting large amounts of burp power to the driver - but it is there if you want it. If you don't need them I suggest not getting them as they can chatter a…

Decided to finally get started on it. The Jeep will be getting a no-wall 4th order build with two 15s. * Battery / Amp Rack area cleaned out... everything un-installed. My multi-channels will sit on those two little platforms where the batteries used to be. * New floor piece cut - everything will attach to this piece. * Of course XS Power D1600s will be used --- That is all for now... just ripped it all out this morning and Brandon helped me cut out the floor piece. Will make progress when time allows.

I bout an SAZ 3000D a couple months ago off a guy. Paid 550 for it. i dont know how much warrenty is left on it. Amy way i could find out? serial number maybe?

Originally posted by Greg Kashin (Sundown Russian distributor) on my SMD Forum : --------- More good news from Team Sundow Russia!!! :clapping: Had to share this... the car belongs to Evgeniy Naumkin who's a regular competitor in local SPL comps. He currently holds the national record in IASCA Stock 1-160 with 152.8 with his old setup. In his quest to break 153 he got a Sundown Audio z12 v.2 d1 sub to replace his well worn Soundstream SPLX. This is his old setup - a quick rundown of the system: 2006 Subaru Impreza Wagon sub - one Sundown z12 v.2 d1 with NS cone and spiders amp - Stetsom 9k2d batts - Hawker 300 under the hood and 400 in the back just one run of + and - 0a…

So... SA-8 a little too big / powerful / deep for you ? I'm working on the E8 v.2 model as well for those of you who fit that description. THERE IS NO ETA OR PRICE YET - MY PROTOTYPE JUST GOT HERE TODAY! Works a bit better sealed as well -- very close to the E8 v.1 in sealed performance. Sticking to the 200 RMS rating of the E8 v.1 but this model is alot more robust -- I did alot of thinking over the last year or so about how to make an affordable 8" driver that can take more abuse than the E8 v.1 could... and this is what I came up with. It will be cheaper than the SA-8 but, obviously, more expensive than the E8 v.1 model. Magnet is 6mm narrower than the SA-8 and only a …

Just installed my Sundown SAZ 1000D in my Camaro. As soon as I fired it up, the protection LED lit (I thought it was the power LED at first) I unhooked the output speaker wires and reset the amp (disconnected power & ground) and tried again. Still had protection LED. I then unplugged the INPUT signals, reset the amp, and this time got the power light (woohoo!). As soon as I attempted to plug in a INPUT line, the protection LED would light up. So it's the input causing the trouble, not the output. I'm using a wiring harness from Sub Thump, maybe it's bad. I checked the wires from the harness against the wiring diagram for the car and everything seemed ok. May…

In Meca where less is more. What fusing should I drop down to on an saz 1500? A little more info for my particular install. Amps SAZ 1500 SAX 100x4 Power Stock alt 2 yellow tops for a total of 88 amp hrs Subs 3 sa 8's I would like to run in the lowest class possible

Sold the last of the SAE-1200Ds today and this line is now discontinued. The SAE-1200D v.2 made big strides in reliability vs. the v.1 model but still does not quite live up to the standard set by the SAZ/SAX series amps in my mind. It was a tough decision as we really wanted to offer a lower cost line but at this time it is not fitting into my plan for Sundown Audio. I've spent alot of time thinking about it and had not made my final decision until today -- I had made plans to introduce matching multi-channels but these plans are now halted. I think the change will be for the better as we can concentrate on our core lines, the SAX and SAZ amps. The SAX-1200D is only slig…

i got this sundown audio E8 with coil rub and i was wanting to know if sundown made a recone and if they do how much?

So im happy to say that ive made up my mind and instead of squeezing 2 HDC3 15's in my truck im gonna go with 2 nightshade 15's since they like smaller boxes. My question is when are they going to be back in stock in the ssa store and are they gonna be the v2 or v1 or both? Has there been any word on how much the v2 is gonna cost?