Sundown Audio

The Sundown 100.4 amp has been sitting in my garage for a few years now. I bought this when they were first released as I think the knobs have changed over time? I can't remember how to setup this amp on my current car. I have components up front and a sub in the trunk. How do I wire this to the amp correctly? Specifically which RCA and Speaker wires go into which terminals? Also how do I go about starting out to tune the system with this setup? Hertz ESK165 edesignaudio 8" DVC sub Alpine 9886 Headunit Sundown 100.4 Amp This is in an S2000 so no rears.

i lost my remote amp controller, and i am looking either for a new that i can buy off sundown, somone that has an extra. or one that i can get that is a different brand that will work on my sundown 1000d. thanks for the help. kevin

Well i bought a few Nightshade v.1 motors from jacobs yardsale a week or so ago. when they arrived there were still cones in place. i checked coils and one of the subs still read good. so i decided to put some power to it. It made music but sounded horrible but seemed to work ok. I bought these to resize/recone and figured neither sub would work, but. 1) 12' blown junkyard nightshade v.1 1) box that leaks and is about 2.5 times too big for the sub. (was made for 3 sa-10s) i re-baffled it to make the show 1) sundown 3k 1) Truck that is notorious for not getting loud. My 4x sa-8s do a best of 143 on music. I took 1st in Streetbeat 1 I slapped this together at the last minut…

Hey guys, I thought I'd start this topic before I istall everything to learn and get some info on how to do it. I bought 50.4 to run Image Dynamics CTX65CS in front and CTX6 in back. Then I grabbed 125.2 to run two Image Dynamics ID8''D4 v.3, both at 2ohm run on separate channel and Trevor at PTS is building ported box for them now. All of this will go to Pioneer 880PRS head unit. I know how to connect everything, I will pretty much get to the part where everytihing is connected and I start to wonder what the knobs on the amp do There's just so many of them any info would be nice....

with my 2000d + 2 12xcon setup. is it possible in the future to strap an amp with less power to the xcons. for example can i strap and saz2000d and a saz1000 together? or do they have to be the same?

I'm looking for a saz2500 and was wondering how to tell the difference between the two? Are there any major differences in them? Thanks guys.

I have breifly looked but can some please tell me how to wire my saz1500 v2 to my FI 2ohm sub for a 1ohm load. Also does it matter which way the rca's are in? (They are not colored red and white on the amp) Pics would be awesome. I know these may be dumb questions but its the last thing for me to do.

This is for the Saz-1000, 1500, 2000, 3000, 3500 and up as well as the Sae-1200. Lets start out by saying that these amps are mono block amps. This means they are internally bridged (paralleled). First lets take a look at the sub. Unless you trim the wire down two 8 gauge are not going to fit in one terminal (if you want to parallel the coils at the sub). So, what I do is parallel the coils at the box. This is a picture of the speaker wires inside the box. This is what it looks like on the outside. Since the coils are paralleled on the inside of the box with the bolts, all you have to do is send two positives and two negatives to the amp. You can even put a set of …

How underrated is the 100.2? I saw jacob post that it is extremely underrated... I was just curious if anyone has any figures.

http://www.elitesummernationals.com/ any one coming to spartanburg sc Saturday?

Huge for sale thread here... I need to get some of this stuff out of here! All prices are shipped in the continental 48 states via Paypal, ask me about shipping anywhere else for a quote. First off... I have 4x SAZ-1500Ds that are used. These amps carry full warranty coverage from your date of purchase. They are very lightly used by Team Sundown members. They are 9/10 on a bad day cosmetically, all look the same with pretty much only minor mounting foor wear. Yes, the logo is upside down on one of them... it is reversible so you can change it back. These are $450 each. TWO SAZ-1500Ds ARE SOLD. TWO ARE AVAILABLE. Second. A used SAX-100.4 that is indistinguishable from br…

Well I was wondering if you got any huge vinyls? Or a file that I could bring to a shop and have them make me a big vinyl? Because as soon as I get the car, Im getting a good deal of vinyls of all my sponsors and supporters on there. Next year should be a big one. Ill have my system done for SBN for sure, and Im going to see if I can get a spot outside so I can demo it. If WF is anything like it was this year, Ill have a spot in the Expo center there too. Gotta let people know whats up! Thanks.

I own a Sae-1200 and would like to show my support for this company. I need one around ~10X2 or something like that for the back of my truck. Anyone have one I could pay shipping on?

What is the fusing of the SAZ-1000D? What is the power inputs? I have seen 3 different specs on three different sites!!! I just want the truth!!!!!

A power testing thread for the SAZ-1000D. So I will post what I found..... These are NOT official testing results. Stock Alt Yellow Top Under Hood Kinetik 2400 in rear Resting voltage at 13.6 ....... I had just been doing TL testing and batts were dead With 2 L7 15"s wiring to .5ohm I got, 1080 watts with drop to 12.9 and imp rise to 1.8 ohm. I now have two of these little monsters and will be doing some more testing soon

Hello. Some of you may know me from other forums. I just thought i would stop by and show off some sundown power! Ive been running Sundown in my Comp/Project vehicle for around 7 months. I compete regularly for the most part locally. The vehicle has now been retired due to the fact that I cant damage it anymore then it already has been. lol Im going to trade it back in for something new. Until then i have a few vehicles that im looking at to make a new project with. I will compete with the vehicle as well. So time is critical. I have to find prep and build in the next 3 weeks to make it without any gaps in the season. Anyways enough of my rant. lol. The vehicle…

i just got me a nice pair of twins! i tested them in my vehicle while at the store, (no RCAs and speakers connected, used my relay) and they 'restarted' like normal.. (which further hints that there was a problem with the 3000D..) anyway, i can't wait to get these connected.. and i just can't stop staring at them..

I just wanted to post up some pics of my second 3000D. The new heat-sink feels a heck of a lot heavier then the old one. I'm going to try to get some numbers tonight. And a pic of what they are powering

so i was tunin my amp for my 12" Q. and i wanted to use as little bass boost as normal on the amp. but even if i maxed out the gains, set my LPF around 80hz, and turned down my bass boost to 0db. i was only puttin out about 17 volts (if i remember correctly i did it early this morning). i know it was below 20.. and i needed about 31.6 volts. is this normal? i used 50hz tone when i had no BB, and when i used it, i used a 60hz tone. the only way i was able to reach my needed volts, was when my gains are just over 3/4 set, and my bass boost is about the same spot, 15-17db. but is that about normal? would it be better if i maxed out the bass boost and compensated with my gai…

Listen 1st of all I posted on here a few days ago about not getting my invoice. I had to go out of town for a job and could not post. This is the 1st chance I've had. Just let me start by saying some of you are so out of line it's unbelievable. I'm a paying customer who spent alot on my 2 amps. All I wanted was my invoice that DB-r fucked up and didn't send. The reason I posted here is because where else do I go when DB-r never get's around to sending the damn invoice? Give me a break I have done nothing wrong at all except ask for the invoice and it's not my problem if Db-r can't seem to remember our e-mail communications in which they told me they would send the invoic…

I have a blown 100.2 from Florida. Only has UPS store address and no paperwork at all. Need some information on who sent this to me. ALWAYS put some sort of documentation inside of a return.

I'm pretty sure I'm ADDICTED..

Will they run on a 16 volt setup? I know that there would be no warranty but have to ask.

If you want a Nightshade now I have some used motors that I can build with new parts. Shipping within the 48 continental states by UPS Ground included : 12" - $425 15" - $450 18" - $475 Limited supply of used motors so let me know ASAP.