Sundown Audio

packaging looked perfectly Jacob, not a mark anywhere on the amp boxes.

Hey everyone.....got the toyota's system install all done....I will post pics and video in a few hours....but the 18's blew the box apart...... haha it sounds like a machine gun in the back bdddddddddddddddddddddddddddddd took about 45 minutes to destroy the box......so next week ill have a nother box on the way...... the shop is going to build another box for me no charge this time its going to be a little more secure....the shop was pissed that them Sundown 3500's teamed with the Btl's were so damn devastating

Wat do you guys think would be louder and better option for my camaro ? I have the power for either and about 3.5 cubes for the box after displacement Wats the max guys are running on these new 8s i have heard some where around 800 rms but i would throw around 500 rms to each just wondering if i should invest in these subs Thanks Guys

Was hoping I could use the stock frame and I was able to do so! Just had to adapt it a bit... one of our spider bolt down rings worked perfectly for the job. This woofer has 3 Hard Nightshade spiders, a Z v.2 prototype D2 coil (tight gap so NS coil would not fit), and a light weight cone similar to the Z v.1 but with a wide roll surround. Once the dust cap glue dries I'll measure specs on it to see what we got * Steel spider ring glued into place (glue under, around, and below the ring) * Overview of the ring -- also changed original basket screws to a higher grade metal with allen heads. * Gluing bottom triple joint * Lining it up and getting ready to solder the lea…

just had to say i love this amp, sounds 100% better than my last sub amp. if your reading this forum like i did before purchasing one, just do it.

Got the amp racks made with Andrew. Wrapped in carpet till we ran out.. All wires ran, tucked away, with a battery tray in the wheel well to hold my batteries. 2 SAZ 3000D's 2 18" Nightshades(custom) 3 DEKA Intimidators 1 Maxx-Link 1 Wall tuned to 65Hz Gonna live soon, wall will be installed this week, so more picstures to come. More pictures soon, how's it look so far? I'm doing my best on this install....I want it to be just straight out god awful annoyingly loud..but I want it to be a very clean install as well.

Expected MSRP to be $139 on these guys. I will do a pre-sale at $95 shipped in the continental USA once production starts.

what ohm load is it safe to burp (2) SAZ3000D's strapped w/ a Maxxlink? Right now, resting load is .8ohms - we have (6) 16V batteries that rest @ 17.4 and are @ 20.8 when fully charged. Would the amps go into protection? Thanks...

Running off one SAZ-1500 in 6 ft^3. Two sets of Peerless 6.5s and selenium horns handle the mids and highs. Sounds great and still have some storage room.

My girl has a e-12 v1 in her car and me forgetting I bought her another one, except the version I bought was a v2. On to my question. I know that they have slightly different T/A parameters but can I use them in the same box?

The sa12s are rated at 600rms but i have seen they can take more. My question is can i safely run two sa12s on the saz1500 at 1 ohm in a daily setup?

Im either wanting to pre-order the saz-1500d v.2 in the next day or two for 400$. Or I was looking at the Saz-2000d in the B-stock Refurb section for 400$ and have a little headroom. Power is going to an XCON by the way. Any input is appreciated.

The victim all torn out progress from yesterday Im working on getting that piece on the other side in Im hopeing to get more done before I go back to work tomorrow not exacly the most motivated person at times its going to be alteast 2 layers on the sides and back and a tripple baffle I might go thicker on the dides depending on how these first layers go up this layer is pretty rough not really that square so I might have to go thicker to get what I want from it no big deal really its just the shape of the bare sheet metal sucks. and the gear

Just wanted to give a public thank you for the amazing customer service!! The amps showed up today, a couple days before I expected them to. I will always give you the first shot at any audio business I may have in the future( and I know I will;)). Just got my 2 sax-100.2's to go with my saz-1500d. I'm gonna try to run them in dual mono to my Diamond d-971 components, I think that will drop my noise levels wayyyy down, and really help my staging/imaging as well. Again, Jacob... THANK YOU!!!

so check this b.s. i bought a couple saz1500s a while back that needed repair. the guy i got them from is saying he's a dealer for sundown now and that its not possible for me to get my amps fixed properly by sundown without going thru a sundown rep. i called b.s. on it and told him i talked to jacob and he referred me to db-r since they are the only guys certified to rebuild sundown amps. he swears that i cant get them fixed and he doesnt believe my amps are at db-r already......... now is this guy really a rep for sundown in oklahoma city? even if he is i'd still rather buy my shit from ssa

check it out, i know sum of you know what i have but lemme get it out of the way. 3 yellow tops, 200 amp alt 1 run of 0 gauge front to back 2 2/0 ground saz 3000d 2 bl 15's 3 250 amp circut breakers..... when i let it wang..... for maybe 10 mins on a constant bass song say i donno somthing young jezzy my circuit breaker between my amp and cell pack pops...,,, my voltage is 13-13.5 this is how my cable goes...... cells.... 15 inches of 0 gauge... circut...3 feet of 0 gauge... amp. jacob.. should i change some chit around? or step up to a 300 amps breaker........ ps NONE of the others are tripping

ok i have my sundown shirt... black is a bit hot on comp days sometimes.. lol.. but i love the shirt... i really think we need hats... i dunno if jacob has something like that in the works but id be willing to pay good for a sundown audio hat....

Was just thinking about where the future of Sundown Audio was heading. It seems to me the company is growing and becoming more and more popular. (correct if I'm wrong) At some point in time I am assuming there will be a need for a new larger warehouse or building, and plans on incorporating standard Bench Tests for all amplifiers? Of course I, as most of the people on the forum know what the ability is of Sundown amps, getting bench results with the amp is always a nice little extra.

I know the sax-100.4 can handle 10-16v but what about a lil above that. lets say from 17-18v. Im trying to run my whole system all on 16v eliminating the extra 1/0 wire running from under the hood and adding to the 16v charging system. thanx in advance

Now that everyone knows what they can do... I am thinking about opening a special on them to get more reviews on these bad boys. The special would be equal to the pre-sale @ $300 each. Who wants some ?

Heres my first post, its been hard in the past for me to sign up on the forum. This is a test from about 2 months ago. Each amp is at .5 ohm. http://s82.photobucket.com/albums/j242/fun...nt=SUNP0001.flv

I currently own a 2000 Pontiac grand am gt. the dimensions i could easily fit in my trunk would be 18x12x38. Could you help me design a box for a SA-15 within those dimensions. Need design specifics and/or cut sheets. I was thinking about going with two tens or two twelves but i don't think the space will allow me to do it, any ideas?? But definitely going with SA subs no matter what. Don't have amp yet but will match amp to subs regardless. Please Help

Any one have them like t/s, mounting depth, displacement etc?

Can't seem to find the info anywhere. What diameter coil do you use on the SA-10?

ok well there is nothing wrong with amp except for the fact that it draws soo much power them most accessorys in my car turn off when the amp trys to hit a real low note. my deck will shut off and so will my radar detector, which is hooked into the ciggy lighter. so im wondering what i should do, im thinking that its from having a lack luster electrical system that is not able to supply the car, and the amp with all the current needed to keep everything running smoothly. the odd thing is the car itself will run just fine with no problems at all. so i was wondering if i should run the subs at 8 ohm each for a 4 ohm load so the amp will draw less untill i can afford some el…