Sundown Audio

Sundown was in attendance big time today. Even Mr. Sundown himself came down to check it out. I hope you had fun and plan on coming down again. We're definately interested in doing a few shows up there in NC.

I figured I would share. I got it installed today. I am down a battery and some power. I had an additional YellowTop and a SS PCA2000D. I really can't tell too bad. Once I get the new battery and upgrade the power wire, I will give her the beat down and report back.

i was always wondering about this lol...how did you come up with the name? any reason or meaning to it, or were u just in the sun looking down and decided to name it that or something ahhah :bigclap:

More power this time... current clamp shows ONE coil. We hooked each coil up to a seperate 120v circuit for a total power of ~8800 watts at the start, dropped to the 7000s then stayed around that point until failure at 30 seconds. Prior to this video we had JUST finished plugging it in to one socket in series for around 2000 watts for FIVE MINUTES - so it was already hot! The Monster lives up to it's name. If you are wondering about the frame... Brandon had two in his wall without motor supports and it broke off some of the screws allowing the bottom to swing out and break off the top of the frame. So... motor supports are a must.

I have 2 ns v.2 12's D2 and 2 3500s strapped to 1 ohm. How ballzy must 1 be to strap to 0.5 for 0.25 each? Would there be a good db gain?

when was it coming again?

For sale. One SAZ-1500D, brand new in box. This unit has a blemish on the finish, but is otherwise brand new. I inspect each one before it goes out and caught this one: $475 shipped in the continental USA. This amplifier carries full warranty coverage.

Jacob, thank you so much for all of the support and finally here it is... the F150 is done mostly. Most of these photos are on my build log posted on the SSA forum. Here is the finished (mostly) product. A few more tweaks are coming a Kenwood head unit, leather interior, some fiber glass work (probably going to put some E8s in for mid-bass), wheels and new paint. Oh did I mention that it's a sleeper?

Well yesterday i went to a car show in my area and me and my teammate path2spl made a folks drop there jaws, pick up there faces, and pretty much chit on themselves when me and path2spl came thru... long story short..path2spl took first place in a 3-4subwoofer class with a 158.1 at the kick with the door open @ 45hz on the ac180mic that was calibrated to be 3.5-4 db's down from the tl mic....u do the math his setup 3nightshade 15's 3 saz1500d's http://sundownaudio.com/rides_dfabio.html second place was 5 db's lower and it had 4 of the new mojo 15's subs up and 2 mmats 3500.1's and third was 1db's lower with 4 jbl wgti 15's in a wall with 2 fosgate t4kw's i was in the …

First off, have to give a big thanks to Jacob for allowing me to use the Sundown logo, and for supplying me with some hi-res jpegs. Finally got some free time in one of our CNC's and got this in. All i have left to do is paint the lettering to make it stand out more. Something wrong with the way the pic came out on this one on the "audio" shape Now to do the other one.

Congrats on your dB Drag ssnw win today with a 154.1 from ONE SUB. One NightShade 15" powered by a pair of saz-3500s on 12volts. I can't wait to see what you do with more cone area.

I'm planning on purchasing the SAZ-3000D for my Nissan Sentra and would like to upgrade my alternator. What size alternator would you recommend?

Well my sa-12 stopped working and I took it out of the box and found this black stuff Idk what it is Is this normal to break and can you fix it? I didnt even have it installed for a month.Help somebody

Can some help me with dimesion for an slot-ported enclosure, for one sa15.I have a 2004 Buick Regal.I'm planning running 750rms to this subwoofer. I need all cut pieces.The height has to be 16' OR LESS.

What would the best wiring kit for the SAE 1200D be? 4 guage? 0 guage? Also is the knukonceptz wiring any good? there prices are pretty cheap

I Dont Really Understand how to bridge a Dual 2 Ohm Speaker, On My Speaker I Have Positive Crosing Over To Positive And Negative Crossing Over To Negative (1 Ohm Load) Like Shown How Do I Hook This Up To The Amp? Because The 2 Outside Terminals Which are Usually Positive Negative Are Positive Positive

sup forum. I'm wanting to upgrade my front stage . i have a saz 1000d with an icon 12'' box built to specs. i'm leaning torwards rainbow slc 265.25 since my id CX.62 v2's blew ( friends borrow + drinking = blown ) the amp i have for them is a cheap performance technique. i was wondering if the sax 125.2 is good for frontstage.. simple question but i want to confirm before spending $$ thanks!

hi everyone need some advice on a custom built box for a single 12 inch sa-12 2 ohm sub. I'll be building the box with 3/4 mdf wood and the space i have to work with is 41 inches from left to right and 17 inches in depth. the car the sub Will be going in is a 2001 kia sportage ex small size suv and the amp i will be useing is a pyle plad3300d which puts out 1200 to 1300 watts at one ohm. now i never built me a custom vented box before but i have built a few sealed boxes in the past so my skill level for building a vented box is low. the music i listen to is rap and hip hop and my goal is to more daily driving and a little competition so i want the most spl i can get but w…

If you want a Nightshade now I have some used motors that I can build with new parts. Shipping within the 48 continental states by UPS Ground included : 12" - $425 15" - $450 18" - $475 Limited supply of used motors so let me know ASAP.

Greetings currently own a z v.4 10. It is a 97 Tahoe being ran off of a saz 2500 v.2. It would be more cost effective to re-cone it to a 18". it would cost little over twice as much two add another z v.4 10, but just because it cost less doesn't mean it will sound better. basically I'm after more output. better low end extension. I had it in my cutlass and it sounded great but in the Tahoe I have a lot more cabin space. any suggestions between the two? thanks in advance for the input.

does anyone know about how many watts a 300d will put off at a .5 ohm. with high output alternator 3 good batts. and around 14.2 volts?thanks for the help guys.hope to get some good numbers!!!

These are from Derrick's Explorer : Starting battery + 2x Powermaster D3100s used for testing 3980 @ 0.25 rising to 0.65 @ 11.2v (engine on) 2050 @ 1 rising to 2.44 @ 12.2v (engine off) ----- These are from Ray Farmer: Okay, I have done my SAZ3500D 12volt power test. I would like to say, WOW!! My nominal ohm load was 0.5 ohms. I did plenty of test but I got the amp to do its power at the proper settings and did 3 test and took the average. I used 2 x NSB-g3100 to power the amp, Starting voltage 13.2 Test 1 75.1 volts 39.9 amps 2996.5 box rise 1.88 voltage drop 12.2 Test 2 75.1 volts 37.7 amps 2827.5 watts box rise 1.99 voltage drop 12.1 Test 3 76.0 volts 39.5 amps 3002.0 …

Who would be interested in an SD-1 v.2 10" woofer sale? Much like the SAX-100.2 I am finding these under-appreciated and would like to see more out there! http://www.soundsolutionsaudio.com/forum/i...showtopic=14141 * Customer Review http://www.soundsolutionsaudio.com/forum/i...showtopic=11420 * Pics from prototyping http://www.soundsolutionsaudio.com/forum/i...showtopic=12478 * More information from the original pre-sale thread back in November 2007 http://www.soundsolutionsaudio.com/forum/i...217&hl=sd-1 * Production model pictures

One of the screw of my 1500D broke (the head) and was a real PITA to remove, but now i need a replacement. Any suggestion? Thanks