Sundown Audio

got my 2 sa-12s in a 5 cube box tuned to 30-31hz using 2 4" aeros anyway i just got my crescendo bc2000 and i was playin today had to be pretty close to full tilt although amp clip light never came on anyway i am very happy with the performance of my amp and subs and box !! once done after about 10 min or so of playing different songs here and there i felt my dust caps and noticed they were luke warm now i went directly to the ports didnt smell anything is this normal ? sorry but first system i have ever had that was capable of actualy flexing anything so i had to play with it

i ordered a 1 x Sundown Audio SAE-1200Dv2 and this is the picture and it just says d not v2 was wondering if it was the same thing or i got sent one of the older ones thanks kevin

any one know what i should set my saz-3000D for at 1.5 ohm's? or just set it for a 2 ohm load?

dam digi died before i got the good stuff , more videos tomarrow still not near being done. adding 4 more 1500d's

im fixing to wire up my 1500D to one sub, how do i go about doing it, just use one + and one -?

hi there, i got a saz-1000d with 1 15" re xxx with FI d1 recone i recently hit 145.2db, i got stock alternator a 525cca engine batt and 750cca back in the trunk and my ported box is 4.0cu/ft what else can i do to raise more db's with the same amp cause i saw in this forum this amp can hit 146.8, so can you help me out with some tips to get my goal thanks, sundown rules

So... the other day I shipped an amp to the town I grew up in -- Severn, MD. Thought that was cool 2.8 miles from the house I used to live in.

Jacob, how did you decide to make the 100.2 and 1500D in the same manual? The only pages they have in common are the Warranty and Troubleshooting.

I know there has been some problems with RCA cables and the amps for some reason. I am considering either of these 2 sets http://www.knukonceptz.com/productDetail.cfm?prodID=KRY4.4M or http://www.knukonceptz.com/productDetail.c...rodID=KARSS4.4M Will they both work and would you recommend one over the other?

I worked all day yesterday getting my Maxx-Link working properly. I'm 99% positive it was an issue with the outputs on my old head unit. Now I'm trying to get everything fine tuned perfect and there are a lot of adjustments on this thing. My only concern is what to set the ouput of the Maxx-Link to? Its currently set to 5v but can I go higher? Will the 1500s take the full 9v output? I checked the owner's manual but didn't see it listed. Also since I'm not using the br output to strap the amps, do I still need to gain match them? How does that work? I'm used to only setting one amp and now its like I have to set both amps and the Maxx-Link which is driving me cra…

Jacob, How would I setup a 1200D and a 125.2, Rca wise? I know how to, but I am just double checking. I would run Rca's from the sub output to the 1200D and Front to the 125. Correct? If I wanted to hook up another 1200D, I would just use the pass thru right? When I get the 100.4 I run Rca's from front and rear right? Just Wonderin so I can have everything when My HU comes in. I'm going out on Halloween and I wanna flex a bit

I noticed that the newest RD Audio class D internals are pretty well identical to Sundown stuff... what's the deal? First they were like atomic, and now Sundown? There seems to be a lot of this going on with amplifiers lately... What's your take on this Jacob?

Had a customer send in a pair of BTL 15s for me to re-build -- first time seeing the new UFO style BTLs in person. Very large and heavy motor on these guys -- also looks like they started using four separate magnets on these rather than a single large slug; presumably to prevent potential defects in the big slug. In any event -- on to the to re-build... the original failure was a burnt up tinsel lead on one of the drivers... so I am using our double lead Z v.2 spiders on the re-builds. * Original Failure Point * I am using a Z v.3 coil -- it is similar in dimension to the BTL stock coil but it is 8-layers vs. 4-layers on the BTL coil... it is 60mm WW vs. 64mm …

To order a re-cone e-mail [email protected] -- do not e-mail my "sundownz" address if you need a quick response.To reduce back-and-forth e-mails ALWAYS include the following : 1) What you are ordering -- Model, Coil Configuration, Etc. 2) If you already have a basket or not; please check below for any special notes. 3) If you need ANY custom options please specify up front. 4) !!! YOUR ADDRESS AND NAME !!! 5) A picture of what you have goes a long way to be SURE we are talking about the same thing. IT WILL TAKE, ON AVERAGE, 10-14 days for a built item like a drop-in to be completed. ---------- EDIT 8/30/11 : WE CANNOT WARRANTY DIY RE-CONE ASSEMBLY ISSUES. Rea…

To order a re-cone e-mail [email [email protected]][email protected] -- do not e-mail my "sundownz" address if you need a quick response.To reduce back-and-forth e-mails ALWAYS include the following : 1) What you are ordering -- Model, Coil Configuration, Etc. 2) If you already have a basket or not; please check below for any special notes. 3) If you need ANY custom options please specify up front. 4) !!! YOUR ADDRESS AND NAME !!! 5) A picture of what you have goes a long way to be SURE we are talking about the same thing. IT WILL TAKE, ON AVERAGE, 10-14 days for a built item like a drop-in to be completed. It may take longer depending on how busy ou…

To order a drop-in re-cone assembly e-mail [email [email protected]][email protected] -- do not e-mail my "sundownz" address if you need a quick response.To reduce back-and-forth e-mails ALWAYS include the following : 1) What you are ordering -- Model, Coil Configuration, Etc. 2) If you already have a basket or not; please check below for any special notes. 3) If you need ANY custom options please specify up front. 4) !!! YOUR ADDRESS AND NAME !!! 5) A picture of what you have goes a long way to be SURE we are talking about the same thing. 6) When you send payment include ALL details of your drop-in on the notes(model, size, coil configuration, options, e…

$60 + shipping each regardless of quantity Need to make room in the warehouse so price is 1/2 what I was originally asking. --- I bought out all of the QC failed SI BM 10s (old models) and re-built them with several changes: 1) Slightly longer flat-wound coil (original was round wire) - USA made coils 2) Narrower / Taller Surround 3) Tied down tinsel leads Measured T/S Specs (coils in series): RE: 6.89 ohms Z: 8 ohms Fs: 27.2 Hz Qes: 0.56 Qms: 3.32 Qts: 0.48 Le: 2.8 mH Vas: 31.1 L BL: 16.2 NA Mms: 124 grams Power: 400 watts RMS 0.95 ft^3 SEALED BOX - F3 of 41 Hz 1.5 ft^3 ported tuned to 30 - 35 Hz for high output I have about 40 of these... These are blow-out items and …

If I place order for two sa12 d4 are they in stock and ready to ship in the ssa store?

On a strong 14v electrical, what can I expect? I have a 275 HO Alt, 3 YT, 4 runs of 1/0 (2+/2-). I've sold my MM 2K autotek and i'll be looking for another bigger amp shortly, and i'm kinda leaning towards this.

Im Rebuilding my s10 dis yr with sum new goodies i had the sundown z15s on 1 ab 500.1 and now im stepping up to 2 Z15v2s and 2 ab 500.1s and adding more 1/0 and 4 big C& D Batts! The old setup with the Z15s did a 152.4 at 38hz at the headrest meca style on 160amps of fusing for s3! But this yr im movin up classes since i got more power!!! Stay tuned http://i49.tinypic.com/1z1wmyt.jpg http://i45.tinypic.com/xlcj8y.jpg http://i48.tinypic.com/29zo1mg.jpg

Ok I searched and couldn't find a thread about the 10" SD-1v2's can anyone give me a suggested enclosure size for a single one sealed? I will be running it with my SAE-1000 at 8ohms if I get it.. Thanks!! David

Just bought a brand new sax100.2 and got it in the mail today and let me just say the sundown pwns my 2008 model RF 400.2 I had in there. the output is better and the sound is "cleaner" if that makes any sense. VERY HAPPY WITH THIS PRODUCT JACOB! Im scared to see what my new 3000D's are gonna do to this truck

Yay, yesterday i recieved my 1500d...First sundown Amp in PR w00t...Thanks a lot Jacob...really nice amp, I love it cant wait to get some subs and batts and install it

Well I got another itch to build another box, so since I was near out of wood and low on funds I was looking around my garage and spy'd a box I had a long while back sitting in the corner. A standard CRX box but with a top plate for 4 10s, so it's 29"x29"x14". So I decided to see what I could do with it, took out the SPAX screws from the top plate, pounded from under it with a hammer and it came off pretty clean. Then fab'd up a box to see if there was some workable area, came up with this. 29x14x16, with a net volume including port of 2.28cuft, there will be 1 45 in the port corner and then .14cuft taken out for the sub itself, should land around 2cuft. Port is 2.25" wid…

I'm planning to run 2 sax-100.2s and 2 saz-3000s strapped at 2 ohms. I have a 200 amp excessive amp alt and i'm attempting to make a bracket so i can also use my stock alt but i'm not sure if i'll succeed in that. Is it recommended to run 2 alts with 2 saz-3000s or would my one 200 amp alt be fine? I'd like to limit the amount of batteries to 1 under the hood and 3 in the back. I'm a little tight on space. Is this alright or would i have to use more? My last system consisted of 2 saz-1500s. Using my 200 amp alt, 1 battery under the hood, and 1 in the back I didn't seem to have any problems at all. Just wondering how much i need to upgrade my electrical to handle 2 saz-300…