Sundown Audio

Just got em back from the machine shop - had to get the holes tapped for basket bolts. I talked to the machine shop about making an optional heat plate as well... would bolt between the basket and top plate. May be an option on these

Just wondering what the output would be on the SAX100.4 in 3 channel configuration on a 2 ohm load. Looking at powering a set of 2 ohm 6.5" comps and a DVC 4 ohm 12" sub. Thanks

* I have just a little bit of aluminum here. * Front brackets to hold them in place will be aluminum angle just like the bars. * Allen bolts + lock washer + brass washer (have one on both sides) * This is where the wires will connect for the amps, grounds, flux caps, etc

I'm planning to run 2 sax-100.2s and 2 saz-3000s strapped at 2 ohms. I have a 200 amp excessive amp alt and i'm attempting to make a bracket so i can also use my stock alt but i'm not sure if i'll succeed in that. Is it recommended to run 2 alts with 2 saz-3000s or would my one 200 amp alt be fine? I'd like to limit the amount of batteries to 1 under the hood and 3 in the back. I'm a little tight on space. Is this alright or would i have to use more? My last system consisted of 2 saz-1500s. Using my 200 amp alt, 1 battery under the hood, and 1 in the back I didn't seem to have any problems at all. Just wondering how much i need to upgrade my electrical to handle 2 saz-300…

Okay guys. I have decided that the program was too successful to cancel over one sour deal. So... it is back. This is what it is all about for those that do not know: * You contact me with what you have that you want to trade-in * I look up average re-sale value and send you an offer * You can choose to take my offer OR NOT but I am not going to haggle, my offer is what it is * If you choose to accept the offer you confirm with me then I add you to the trade-in list * You ship your amp(s) in so we can test them * You can either send money with the trade or we can contact you after testing for the balance via Paypal * Once the balance is paid, if there is one, we ship your…

how much power does the sax 50.4 put out? im think bout giving my wife my t5002 and use the sax 50.4 to run my component active

What is the fusing of the SAZ-1000D? What is the power inputs? I have seen 3 different specs on three different sites!!! I just want the truth!!!!!

What do yall think about 4 Z15"s in 16^3 tuned to 32 with a SAZ-1000D per woofer? Time to get musical in the truck.

2 days ago i replaced that old, OLD pioneer head unit with a clarion flip out(vrx765vd) but im unsure as to where i put my amp rca's, i mean it has like 4 pairs on the back of the head unit.....right now i have it on "non-fader output terminal" should it be on "rear audio output terminal"? it also has "front audio output terminal" which i didnt use for obvious reasons.......sorry for the newbish question....but this was my 1st reciever install!!!!! oh, and the box in the vid was a first too....got anxious so i didnt sand/paint/carpet anything but honestly i kinda like the "raw" look.....besides the glue smear lol also another question, if i may.......do you think interna…

Hi, i hope you unterstand what i mean with fm radio disturbtion.. I have a ssd 10 dual 2 in 1.4 cuft ported to 36hz and it needs more power than it has right at the moment. So i was thinking to buy a saz 1000d or the sale sae 1200d. I know shipping to germany will be expensive but i want to try sundown amps :-) But i wounder if these amps disturb the receiving of the fm signal, because i had a t20001 in my car an didnt virtually receive any station anymore... Can you help my a bit with my decision??

i have an older box that was given to me by a friend who works at a shop.... he said that he really didnt know what it was tuned to but the 11.5 long and the only thing he remembers ( which was written on a sticky from the guy who built it) that the box had 26.43 cu. inches of area, 1.48 cubes .... so some ruff calculations on my part which i suck at i am still unsure on what this box is tuned to.??? JUST A TEMP BOX UNTIL PETE AND I GO OVER THE NEW BUILD WITH 15 NSs... i spoke with him last week and was think going with a horn design.... could get interesting.

well i use going to go with aq hdc3 18 but i love the way the z 15 look and i love sundown products. here the problem i dont know which set up would be better. i going to buy my subs on wensday and i dont know if u should get 2 z15's d4 and run them at one ohm to a saz3000d or i should i get 2 z15's d2 and run the at one ohm to each saz 1500d or should i just get another t10001bd and run each z15 d2 at one ohm to each t10001bd?

i have a pair of sundown sd-1 v2 10"s and im wondering how big of a box they should be in?? i have them in 2 cubes at 28hz right now and they sound good but i just wanted to know for sure if the was was the right size or if i need to build a bigger or smaller one for them?? thanks fo rthe help

http://www.youtube.com/watch?v=YhCUZCG8l5w http://vids.myspace.com/index.cfm?fuseacti...ideoid=54115137

All specs measured after a short break-in period. Specs will vary slightly from unit to unit and with further break-in, as with any subwoofer, but these specs are accurate enough to model up your enclosures. 12" Model D1 Coils: Qts = 0.40 Qms = 6.83 Qes = 0.43 Fs = 43 Hz VAS = 11.7 L Le = 1.4 mH (series) Re = 1.59 ohms (series) BL = 17.6 N/A 12" Model D2 Coils: Qts = 0.44 Qms = 9.36 Qes = 0.46 Fs = 41 Hz VAS = 11.7 L Le = 3.0 mH (series) Re = 2.92 ohms (series) BL = 22.8 N/A 15" Model D1 Coils: Qts = 0.48 Qms = 9.33 Qes = 0.51 Fs = 40 Hz Vas = 36.7 L Le = 1.36 (series) Re = 1.44 ohms (series) BL = 15.27 N/A 15" Model D2 Coils: Qts = 0.44 Qms = 8.64 Qes = 0.47 Fs = 38 …

I know the amp has not been released yet.. But I have preordered the amp through a rep and is expected to come in the beginning of june. Any recomendations of electrical upgrades on my vehicle. batteries, wires, alternator, etc...I have a 2000 Honda passport lx. I will also be running a sax-100.4 also. I'm trying get everything as good as it could get so I can run the amps efficiently and get its full potential without blowing them.

Ok I am buying a little Mazda MX-3 Hatchback to have some fun with SPL local shows. I want to buy this guys NS 18 and I need enough power. Mostly for daily with some burps a weekend a month.

Well, it was a nasty rainy day, but there was still a huge turnout. We all did pretty well with the exception of a few fuse problems. http://www.carlisleacoustics.com/albums/th...ls.php?album=47 Corey Mitchell 1 Sundown 1500D and one 12" Nightshade @ 34Hz 1st place Drive-By 1 with a 120.3 (40 amps of fusing) 2nd place in Street 1 with a 144.5 (40 amps of fusing) Jeremy McCord 2 Sundown 3000Ds and two 15" Nightshades @ 43Hz 1st place in Drive-By 4 with a 129.4 (320 amps of fusing) 3rd place in MOD 3 with a 149.9 (160 amps of fusing) Josh Newton 4 Sundown 1500Ds and 8 15" MA Audio XLs @ 31Hz 1st place in MOD4 with a 155.5 (240 amps of fusing) 2nd place in Drive-By 5 w…

I have 4 Dual 2 subs and i want to hopefully run 2 3000's so each amp will see a 2ohm load. with them strapped will that make the amps run full power

As long as I don't let my voltage drop I should be able to strap them at 1 ohm right ????? what is a 3000d rated at at .5 an ohm has any one ever tested them??? plan on runnning four dd 12's 3500 or 9500 at 1 ohm is it worth it??

Hi, I have just sold my Mmats 3500.1 amplifier as it didn't have the subsonic option and I just wanted a change... I was looking into a Sundown 3000 amplifier but after speaking with our UK dealer (DirectIce) I have been advised they are being replaced with the 3500 version. He is still looking into if he can get hold of the 3000 for me, any ideas and prices for both? In

Hi, I decided to buy a Nightshade... But I don't know if this thing fits my car So I need to know what's the minimun enclosure size and tunning for a single NS 15" D2 paired with Rockford Fosgate T1500-1BD 1.5k @ 1ohm

I have a blown 100.2 from Florida. Only has UPS store address and no paperwork at all. Need some information on who sent this to me. ALWAYS put some sort of documentation inside of a return.

Im ordering through KNU and im using a cde-102. for powering im using **NEW** Kolossus Flex 0 Gauge Power Kit but for rca/remote and speaker wire i have no clue. I will be using it on a 18" fi BL. Any tips?

Just wanted to publicly thank Jacob for his support with my cause! A great guy with a big heart and with a great product! To save some typing, here is a link: http://www.soundsolutionsaudio.com/forum/i...showtopic=26719 That right there my friends shows this company is going places.....well besides DOMINATING SPL events.