Sundown Audio

Just curious about a few things. I will be doing 3 of them in a c pillar wall so i am curious about how far would i need to keep the subs surround away from the back seat? Also how much would it have mattered if i got these d2 ohm and have them wired at 1.35ohm powered by 2 AQ2200 strapped together?

So a good portion of the new raw parts arrived today -- nearly a full 40' HQ truckload of soft parts and frames. Plus, of course, additional E, SA, and Z v.3 style parts! Still have more that will be arriving on our next two containers as well to complete all of the parts we need for X, Z v.4, and NS v.3 drop-ins / re-cones... will be partial containers of parts on those as many of the out-of-stock woofers will be coming in on those trucks as well (SA and SD-2 lines). I don't think very many people realize just how many raw parts we keep in stock here but this is a nice peek into that The fully built X and Z v.4 are still moving along according to the ETA in the pre-s…

I have a saz3500 that i bought with my z v2 15's and i was wondering whats the difference in the models

The new NS-1 production run started last month and is due mid to late April coming up : NS-1 -- Website page with details. 6500 watts rated @ 1 ohm Regular cost is $1900 PRE-ORDER COST IS $1500.00 shipped in the continental USA only. AK and HI get quotes from us or your favorite dealer. During the pre-order you can order from us via Paypal to [email protected] or call 704-528-9700 Ext : 3 and order with Debbie over the phone. You can also order from any local or online dealer. International contact your local distributor or online dealer.

Will mixing 2 different sub models produce any cancellation if they are in seperate enclosures and same size? ie, Using a SA-12 and a Z v.3 12"; strange question I know, but can't find info on it.

Looking for box size for 2 18 zv3 I want 4.5 net each but what size aero ports? And how many?

I have a 2012 Silverado Crew Cab, with limited space under the seat, and don't want to raise the seat. I found a pre-made box that basically represents how much space I have to work with, and it just so happens to have measurements with it. 51" wide, 17 3/4" deep, 9 1/8" high in front, 5 1/8" high in back. http://www.audioenhancers.com/vehiclespecific/crew180.php I also saw this box, and got an idea. http://subthump.com/Chevrolet-GMC-Sub-Boxes/Silverado-Sierra-Crew-Cab/07-Up-New-Body-Style-GM-Crew-Cab-Quad-8-Front-Fire-Box.html If I took the measurements of the first box and built a box for two forward firing SA8 V2's using 3/4" MDF, is there an aeroport configuration por…

Does anyone here have these components? if so how do you like them and how much power can they handle

Anyone know a sub box build for a saturn ion 2 coupe. i would like it to be in the low 30s thanks

Sundown's website is not working for me and by searching I have found confliciting measurements.... So anyone know 100% what the cutout diameter is for an SA-12? Thanks.

Thanks for taking the time to read this and give advice! Currently I have 2 SA-12D4's in my car, each ran by a separate MTX 1501d amp. Each sub should be getting about 750 watts at 2 ohms, and is in a 1.75 ^ft ish ported box each (or atleast close). I started with the pair of subs and 1 amp before before adding on the second amp. Here is my issue. These amps can handle 1 ohm loads and is currently seeing 2; thus the subs are not getting the power they deserve. I am torn between 2 thoughts I'm hoping you can help me out with. Should I replace my 2 current sa-12d4's with the 2 ohm models and really push them, or would I be better off buying 2 more 4 ohm models and addin…

Hello. I've got a ported 5.3 cu.ft box and 1.6k amp (my box is 1.1 cf ports and 4.2 cf for the sub) which sub would be better with my setup? the Z v3 15" or the 18" ? also I've got XS power D2400 battery. I cant get a bigger box, thats the maximum box size that I can have. is my mono will be enough for that sub? (can't change it, I'm out of budget) is that box is enough for the 18" ? if not, is it good for the 15" or is it too big? * car details: I have a Fiat Grande Punto (small car. hatchback) and my box is slanted front if it matters. Amp: Celestra FA1.6k Thanks, Udi.

Our ETA is roughly the end of June on these; as always this can vary a bit based on parts supplier production times, transit times, customs times, etc. Based on our average shipping time that is our best estimate. That being said this pre-order will ONLY be open to the public until April 15th, 2013 -- OR until a given size / coil configuration sells 50% of the quantity being produced. I do not want to be out of stock instantly so we are running this much shorter than our other pre-orders. This pre-order is for the USA ONLY -- check with your distributor if you are outside of the USA; if you do NOT have a distributor in your country you can check with us. The below rates…

i got a saz 1500d 2005 chevy colorado and a fi bl 15". i was just wondering for the the power/ground wire, it says its recommended 0 gauge wires. but i have 4 gauge. will it be ok to use it or will it damage the amp and/or go into protection? has anyone used 4 awg for that amp?

got a good deal on a saz1500 v2 .. what is the difference in the v2 and v3 .. I don't want to feel outdated lol. will be using it to power a 10 inch xcon sealed

Some of you may know that I was going to get Sundown X 12s and then decided to get 2 10s because I couldn't fit 2 12s properly since they require a much bigger box and I'm kinda limited on room. I decided to have subs/port facing rear and have my battery and amps up closer to the front and build an amp rack there. I have a box design for the 10s here it is: Sundown recommends a much larger box (1.5-2.0 cubes per 10) to utilize the new surround and suspension. It will get much more excursion then. Also minimum required port area for these 2 10s is 75in2. Well I've been thinking since I have a height of 17 and a width of 34 I could fit 2 15s on the face. However, the…

wrong section

So I just purchased a Sundown SA12D4 installed it and had about an hour worth of play before it decided to go out on me that same day. I have it hooked up to an Alpine MRX M110 rated at 1100 rms at 2ohm, wired with kunconceptz kolossus flex 4 gauge kit, Kinetik hc2000 for power source (battery is located in the back), and a ported enclosure 1.75 cubic feet tuned at 35hz. I had the gain a little less than half to break sub in first when it started to smell really bad then almost immediately it blewi think and now it sounds like crap. Ive had these subs before amd over powere them without any issues. Do you think its worth the hassle going through the warranty exchange...…

To order a re-cone e-mail [email protected] -- do not e-mail my "sundownz" address if you need a quick response.To reduce back-and-forth e-mails ALWAYS include the following : 1) What you are ordering -- Model, Coil Configuration, Etc. 2) If you already have a basket or not; please check below for any special notes. 3) If you need ANY custom options please specify up front. 4) !!! YOUR ADDRESS AND NAME !!! 5) A picture of what you have goes a long way to be SURE we are talking about the same thing. IT WILL TAKE, ON AVERAGE, 10-14 days for a built item like a drop-in to be completed. ---------- EDIT 8/30/11 : WE CANNOT WARRANTY DIY RE-CONE ASSEMBLY ISSUES. Rea…

Watsup fellas, so I got a new Sundown SA12D4 after I blew my other one and I got some questions in regards to setting gains to prevent this from happening again. So my setup consist of a single sundown SA12d4 in a ported box 1.75 cubes tuned at 35hz, wired at 2ohm to an Alpine MRX-M110 (rated 1100rms @ 2ohms), and Kinetic HC2000 w/ knuconceptz 4g kit. So i set my gains with a DMM using the equation squareroot(rms×ohm impedance). Since my amp is more powerful I downgained and used the rms rating for the sub instead of the amp in the equation which gave me squareroot(600×2ohm)=34.64voltage. What I'am wondering is if id be able to raise the gain past that to perhaps squa…

I have a few quick question about the sub box that I am going to be building. First I have two SA-10 D4's wired down to 1Ohm, being powered by a SAZ-1500V3, currently have a crappy prefab enclosure. Though the subs still sound great I know they can be much louder. I have used a few online calculators as well as design software to build a basic ported box. I just want to verify that the box design I have will be sufficient. I've been playing with some numbers and I'm curious about port recommendations as far as width and length Current Box design is a simple ported box with a side slot vent, subs are sharing air space. I'm using RE audio Box calculator specs are Wid…

I'm looking for a saz2500 and was wondering how to tell the difference between the two? Are there any major differences in them? Thanks guys.

First one is complete. This should take care of alot of common and uncommon questions about our woofer dimensions. I am looking into printing them at full scale on our packing boxes as well. I'll be adding them to the X thread when the X drawings are done and will also add them to our site for pretty much every model woofer we make.

I'm running two Sundown amps, now discontinued, an SAX 50.4 for front coaxes and then lineout from that into an SAZ 1000D for the subwoofer. One of the front inputs on the 50.4 broke off, so for a temporary fix, I just ran the outputs from the stereo into the rear inputs. It was just the other day however, that I noticed I no longer had any bass coming from the sub. Now before I go tearing everything apart to see what's wrong, my first instinct was to assume that the line output of the 50.4 receives it's signal from the left and right front inputs. So if I'm using the rear inputs only, no signal to send out to the sub amp. Would this assumption be correct? I really …