Sundown Audio

So the single SA-8 v.2 has been doing great for quite a while with the PSI PR but now that production is in and all pre-orders have shipped I decided I wanted to step it up a bit to THREE of them. Derrick came up today and put together a nice box for me for the three 8s using a single 6" aero-port about 28" long or so tuning us in the low 30s. Box is constructed of a single layer of 3/4" Russian Birch plywood. * Yep... that is a LONG port. * Inside view -- just a basic box with all the giant motors hanging out. * Sealed with a bit of silicone. As we may be tweaking some more I just ran the wires through the port for the time being. * In the car. * Bit close to the…

decided to try an sa15 out powered by channels 3 and 4 bridged on my 200.4. 900-1000 watts roughly. this box is 3.8 cube after displacement with a single 6" aero 17.5" long tuned to 31ish hz lol. 17x31x17 is the dimensions. not shooting for huge numbers just wanted to throw something in my gas saver daily driver. 1991 civic hatch behind the seats. so ill still have full function of my rear seats. eventually ill buy a round over bit to round over all the edges but right now this is where its at. not sure how long ill be using the box cuz im sure someone local will decide to buy it just like every other box i seem to build haha.

I entered my Passport in a small sound-off at Hooters today. I'm running 4 Elemental Design 13kv2 in a sealed downfire box off 2 sae-1000d strapped at 2 ohms. It only hit a 143.2 with a termlab mic, but considering the flex that a Passport has, and the intense heat out there, I can't complain too much. No one did anything spectacular. I think the highest reading was a 149.3 in a higher class than me. BTW, I have never built a stereo for competition purposes (including this one) and this was my first time to ever enter into a competition, so I was pretty stoked about it.

I am wanting to use 2 of these for mid-bass and when I say mid bass i mean 80hz to about 350hz or so what type of enclosure should a try sealed or ported? Thanks, Brock

i will be running 6-eminence alpha-6c's(4ohms,100rms) and 2-boss audio tweeters tw12(4ohms,50-75rms) and im confused as to which 4-channel amp to get considering the 50.4 looks as if it only has the hpf going up tp 3,000hz on two channels only and wondering if im reading it wrong. is the 100.4 the same as well or is their a special way to use the 50.4 in my application. two channels will have two eminence's on them each and the other two channels will have one eminence and boss tweeter each. if i get the 50.4, channel 1&2 will be dedicated to eminence and boss tweeter, while im confused on how to run the two eminence setup on channel 3&4 with the hpf only going to…

Been working on an install for a guy and finally got to his front stage tonight. AA poly mids & CAL25 tweets running active off a 100.4 I spent about 5 minutes figuring out the dials, etc... and did a "best guess" for initial settings, then played some test tones to dial it in. I was SO close from the start and it only took about 30 minutes to get it all set up and sounding good. VERY nice amp for running active!!! Can't wait to strap the 1500D's to his sub tomorrow...

Hi Im very interested in getting my TC-3hp motor rebuilt. I was wondering if you could come up with a recone kit for it. I have the TC-3000 top assmbly. Would you be able to re-use the basket? Would I need to send the motor in or would you be able to send out a re-cone kit? What would the costs be? basically the former on the TC soft parts seperated from the titanium cone. I have had nothing but problems with the TC soft parts. I definitely want a fiber, paper, or plastic cone. The box I am using is 2.94 cubic feet tuned to 34 hz with 56 square inches of port and I am shooting for around 1500 watts rms power handling. Do I have any options with the recone kit?

I'm going to run two sets of Infinity coaxials, so four speakers total. The 100.4 would be a better choice than the 100.2, correct? My sub will be run on a Sundown SAZ-3000D.

Will a Sundown 200.4 work with 2 sets of re audio 6.5 xxx comp set and 1 set of 6.5 merlon coaxial speakers? i know the sundown amp is powerful so i just want to know so i dont blow any speakers

Where should i set my ssf filter to on my saz-1500d? Using it to push a AQ hdc in a 3.5 cube box tuned to 38.

whats the difference between the saz and sae line in sundown amps?would the sae1200 be pretty much equal to the audioque 1200 as far as power?Each would be pushing to ssa icon 12

Just wondering if you were planning on going to ces jacob...

i asked this question last week if a factroy 140 amp alt, 2 hc2000's redtop, 4 runs and a big3 could run 2 1500d's and jacob ok'd me. BUT will that alt be able to charge all 3 batteries? i'm asking because not alot of companies make a HO alt for the 2000+devilles yet. it sucks. thanks in advance.

Ok got a little creative mood again, and someone had asked for a blue theme sundown wallpaper so I came up with this today, hope you guys like. You can download the zip which has 3 sizes from 1920x1080 to 1280x720 here Sundown Wallpaper 2

So...when do the specs on these get released? Very interested in the 4000 variant.

Congrats to CnJ autosound one of my dealer in the philippines for winning first place in several competition. FI BTL 12 with an enclosure tuned @ 39 hz powered by 2 Sundown SAZ1500d strapped with 2 powermaster xs3100 Surprisingly did a 146.2db sealed on dash and the cd played is lollipop by lil wayne.

Hello all, My question is as follows: When utilizing the RCA output on an amp, such as the 125.2 or 50.4, how is the outputted signal affected by the crossover and gain settings of the amp it is coming from? For example, if I were to use a 50.4 to run tweeters and mid range, and then I wanted to utilize the RCA out of the 50.4 to connect a 125.2 which I would use to run mid-bass. Will the RCA out of the 50.4 only pass the higher frequency signals that it is set for to run the speakers connected to it, or will it simply pass the signal through that it is receiving from the head unit? Thanks for all of the input in advance!!!!

I am back from SBN... will take me a few days to get rolling again but we are working hard on e-mails, the SA-8 pre-orders, and any other orders that have been placed !

i have been wondering why there is no iinformation on www.sundownaudio.com about the SAE-1000D? is it old? or do you guys just not make them any more? i bought mine off db-r.com a couple months ago.. so the only chance i would have of finding another SAE-1000D is if i buy it from another person?

Hey guys I am looking for a total of 2- Sundown stickers. I don't really know where to get a hold of them and i know Jacob is a busy guy so I just thought i would post here! i guess if someone has unused sticker they don't want to use send me a p/m. thanks Kenneth

After reading the FAQ, it seems that the speaker wire outputs are parallel wired inside the amp. I'm trying to wire a SAZ-3000D for a single one Ohm load. Do I need to sum the positives and negatives outside the amp or can I just pick one set of + and - and get the full wattage out of the amp. Thanks. Carl

$400 for an SAZ-1500D until August 31st They are IN STOCK and ready to ship. My way of saying "thanks" to my customers over these past three years! This is the lowest price ever seen on the SAZ-1500D. Send me a Paypal to [email protected] with Note "SAZ-1500D SALE" OR Talk to your favorite Sundown dealer !!!

What is the best way of purchasing a SAZ-1500d?

So I just got my SAE-1200D in the mail and installed it. Im pretty sure I installed everything correctly. This is far from my first time wiring an amp. The issue I had was that I couldn't get any sound from the subs so I started trouble shooting. I had good power, ground and remote cause the little green light was coming on, I checked my wiring for the subs and everything checked out there so I figured the problem must be in the RCAs. I check the HU to make sure the subs were turned on and they were. I broke out a new set of RCAs and ran them unimpeded to the amp and still got nothing. Then i decided to move the connection from the INPUT to the OUTPUT and voila, I got m…