Sundown Audio

Alright Everyone Here Goes Another Post. My Current Setup Is One FI 15'' BTL With A SAZ 2200 D Amp. Now I Was Wondering If I Put This Setup In A BMW if If Would Hurt The Amp Or Alternator/Battery With Stock Electrical. In The Long Run My Plans Are Having 2 FI 15" BTL's With 2 SAZ 2200D Amps Running A Total Of 4400 Watts. Also Im Planning On Having A In Dash Head Unit That The Screen Comes Out When You Turn It On And Also 2 Screens On The Headrests. Could Anyone Tell Me Some Info On The Electrical System What Would I Need For All This Whether It Be Battery's,Capacitors Or Alternators. Thank You ~ Kent ~

I assume this is normal. Just curious what causes it to make a clicking noise when turning the amp on or off?

I see there here in the SSA store but say pre order on them still. How would i go about getting my hands on 2 of these subs?

Wondering what the power outputs are for these? Looked in the store but didnt see them there

i have a 3500d if i run it at 4 ohms would i still need to upgrade to more batteries and alt or could i just have the big 3 done.

since it is gonna get cold soon, do you have any sweatshirts? if so how much?

Trying to see if I can get a response from Jacob from Sundown on here about sending my amp in for repair. i believe its pretty much screwed due to low voltage. It was ran off stock alt and stock batt with 1/0 ga ran and 1/3 big three done. i'm hoping to send it in and put a optima or kinetik up front and do the big three. but i cant get a response from jacob ive emailed a few times over the last two days to no avail but I know hes busy. Thanks, Nick

First off... I have to ask: will it be as efficient as a brand new one? Secondly... what voltage should I expect the true 1K RMS @ 1-ohm?

Was wanting to know if this wire is good enough for an saz3000d amp. Also what electrical would be needed?

My 1st video, I hope you guys enjoy it! http://s285.photobucket.com/albums/ll74/an...UDIOSUNDOWN.flv

Is there anyone in the Dallas area that can build me a box for 2 Sundow SA -12's?

Can i have it for x-mas?

I know most amps have to battle heat to stay running as my last amp use to operate well into the 150 degree range on a normal basis but I just have one question. Wheres the heat at on this SAE-1200D???? Ive been bumping hard for 3-4 hours straight and not even a sweat. I can touch it at the end of the night and the heatsinks drain the heat out of my body. How is this thing suppose to be a normal amp????

port is 8" with a 3" flare. the bottom peice is going to be the back of my box.I still need to do some rounding and bondo but you see the picture's

On June 24th 2011, I ordered a pair of Sundown Z-18 v.2 D2 Subs from woofersetc.com Roughly a week and a half later the subs were received but when unboxed the basket of one of them was severely cracked in 2 places. I contacted woofersetc, and they set up a claim with fed ex. Roughly a week later fed ex came out and picked up the sub and due to some type of miscommunication it was shipped all the way back to CA. The sub wasn't supposed to go back, due to a shortage of baskets they were searching high and low for a basket and I was going to get broken sub back, transfer the magnet assembly and re-cone it myself. After several phone calls and emails to both sundown a…

Looking for box size for 2 18 zv3 I want 4.5 net each but what size aero ports? And how many?

seeing as i finally decided i want to wall off my truck, i need a few opinions and specs. i was wanting to know if a 14^3 box would be to big for 2 18s. i want the box tuned super low, and i've already done some calculations, and with a 14^3 box and the 4" ports i already have made. it would tune the box to 22-23hz. so the other thing i need to know, is what do one of these subs require for port area. with 6 4" ports, i have around 75^2 inches of port area. would this be enough? or do i need to go with bigger ports?

Install is thursday morning..and im just checking....I have 2 18" Btls fully loaded Dual 2's and 2 Saz 3500d's, amps are gonna be strapped...this is the best configuration? Thanks, Freddy

alright im putting a new system in my 2004 pontiac grand prix here are the products Pioneer AVIC - Z2 2 Concept 9.2" headrest monitors 2 Sundown 3000Ds Two FI BTL 12"s fully loaded Now here is the question i have a sound stream BX-12 sound proccessor with 13.5 volt sub outs and also a Fusion EQ/CROSSOVER/LINE DRIVER with 8 volt sub outs. Now I should i include either one in the setup or im also looking in to getting the AudioControl DQS with the digital Control PAD. RCA's are high quality Kicker shielded cabling. If you need more info just post or PM me

Our friend Nick Lemons (of Obsidian Audio and Stereo Integrity) was diagnosed with Multiple Sclerosis about six years ago and a good friend of ours, Terri, will be riding her bike in a huge event held every year to help raise awareness and funds to find a cure for MS. Terri will be riding in the Bike MS Atlanta Ride this September 14'th. From now until September 14'th for every $10 you donate you will get one entry towards the raffle to win a pair of Obsidian Audio 12" v2 subwoofers and a Prototype Obsidian Audio OA-1 1200 watt amplifier PLUS a pair of Obsidian Audio ST-1 tweeters! For instance, if you donate $50 you will be entered five times. If you donate $100 you wil…

Hey Jacob, I am looking to make an amp rack in the wheel well and I will be putting 3 amps in it, the 1200D, 100.4 and 125.2 for now.. I was wondering if I do this will I need to add a fan or anything? or do you think it would be better to make an amp rack on the top of the trunk? Perhaps even on the Box if I have room? just wondering what you think I would need if I am forced to go with the wheel well, just don't want them to run hot due to insufficient ventilation. Thx Josh BTW Those amps are quite beefy and look great!

alright, can i set my remote gain to where full remote gain is peak for me. by setting the amp gain low, and having the remote gain hi will that mess the amp up or send a clipped signel i know with the hifonics you can not use the remote gain as a volume knob for the amp, but the hifonics remote gain for the goliath is a input adjuster, so it raises and lower the input signel, i wanna make sure my sundown can dothe job or not also jacob i got no sundown swag with my amp.... can i get a sticker or somthing:D and a flyer,

Im ordering through KNU and im using a cde-102. for powering im using **NEW** Kolossus Flex 0 Gauge Power Kit but for rca/remote and speaker wire i have no clue. I will be using it on a 18" fi BL. Any tips?

Do you have a estimated shipping weight possibly before and after packaging? I'd appreciate it, Thanks

Jacob I need you to review this electrical for use with 2 saz 1500's strapped at 1 ohm. 180 alt 2 batcap 2000.